System Sensor FAAST XT Pro I56-6500 User manual

Brand: System Sensor

Model: FAAST XT Pro I56-6500

Category: Fire protection

Type: User manual

This manual is also suitable for

FAAST_XTPro_9440X

1 I56-6500-000

10-05

SPECIFICATIONS

Electrical Characteristics

External Supply Voltage 18 – 30 VDC

Remote Reset Time External monitor must be pulled low for a minimum of 100 msec

Power Reset 1 sec

Relay Contact Ratings 3.0A @ 30VDC, 0.5A @125VAC

Environmental Ratings

Operating Temperature 32°F (0°C) to 100°F (38°C) – Factory tested to 131F (55C)

Sampled Air Temperature -4°F (-20°C) to 140°F (60°C)

Humidity 10 to 95% non-condensing

IP Rating IP30

9440X FAAST

Fire Alarm Aspiration Sensing Technology

INSTALLATION AND MAINTENANCE INSTRUCTIONS

I56-6500-000

3825 Ohio Avenue, St. Charles, Illinois 60174

1.800.SENSOR2; Fax: 630.377.6495

www.systemsensor.com

The purpose of this document is to provide practical information for

mounting and connecting to FAAST XT PRO. For full product informa-

tion, which includes installation guidelines, instructions for safe use,

smoke sector identification procedures, and warranty and safety informa-

tion, refer to the FAAST XT PRO Comprehensive User Guide available at

systemsensor.com/iFAASTXTPROuserguide or by scanning the QR code.

ITEMS INCLUDED WITH UNIT

• FAAST XT PRO (9440X) unit

• Mounting bracket and hardware

• Installation and Maintenance Instructions

• USB interface cable

• PipeIQ® software, comprehensive manual, and other helpful documents

may be downloaded at systemsensor.com/faast

CONNECTING TO FAAST XT PRO

FAAST XT PRO requires a configuration download from PipeIQ in order to ini-

tialize. This connection can be achieved using either the USB port located on

the front of the device, or the Ethernet port located inside the wiring cabinet.

CONNECTING TO FAAST XT PRO VIA USB

NOTE: In order to connect your computer to the FAAST XT PRO using a USB

connection, a USB driver must first be installed. The driver installation oc-

curs during the installation of PipeIQ version 2.0 or later. Once the driver is

installed, connect to the device using the following steps.

1. Launch PipeIQ. (Download from systemsensor.com/faast.)

2. Create a new project and select FAAST XT PRO device, or open an existing

project.

3. Expand the tree view in the left side navigation pane to reveal the device.

4. Right click on the device and select ‘Connect Device’.

5. Select ‘Admin’ and enter the password – the default password is ‘pass

word’ – then click ‘Connect’.

6. Upon connection, a green dot will appear on the device icon in the navi

gation tree.

CONNECTING TO FAAST XT PRO VIA ETHERNET

Default Device IP Configuration

IP Address: 192.168.1.10

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

Primary DNS: 0.0.0.0

Secondary DNS: 0.0.0.0

CONFIGURE YOUR PC

Your PC will need to be sitting on the same local area network as the FAAST XT

PRO device in order to establish communication. Change your PC’s IP address

to 192.168.1.15 by:

1. Accessing your network setting in your PC’s control panel.

2. Open ‘Local Area Connection’ settings and select ‘Properties’.

3. Select ‘Internet Protocol Version 4 (TCP/IPv4) and then select ‘Properties’.

4. Select ‘Use the following IP address and enter 192.168.1.15. If the sub

net mask does not automatically populate, enter 255.255.255.0 into the

subnet mask field.

5. Click OK, and close out of the network menus.

Important Note: Before changing your PC’s IP address, be sure to take note of

whether your IP is currently dynamically set, or is a static IP address. If your PC is

assigned a static IP address, make note of the IP address and subnet mask so that

you can change back to the proper settings after the FAAST XT PRO is configured.

CONNECT USING PIPEIQ

1. Launch PipeIQ. (Download from systemsensor.com/faast.)

2. Create and save a new project, or open an existing project.

3. Expand the tree view in the left side navigation pane to reveal the device

4. Right click on the device and select ‘Connect Device’.

5. Select Host/IP and type in the device’s IP address - default is 192.168.1.10.

6. Select ‘Admin’ and enter the password – the default password is ‘pass

word’ – then press ‘Connect’.

7. Upon connection, a green dot will appear on the device icon in the navi

gation tree.

INSTALLATION

This equipment must be installed in accordance with all local and national

codes and regulations.

PIPE INSTALLATION

The pipe layout is designed using the PipeIQ software package. Refer to the

Comprehensive Instruction Manual to design the pipe network. All pipe must

be installed in accordance with local and national codes and regulations. The

pipe network should be complete before proceeding with the physical and

electrical system installation.

2 I56-6500-000

10-05

PHYSICAL UNIT INSTALLATION

WARNING

Make sure that there are no pipes or electrical wires within the wall before

drilling any mounting holes

SECURING THE MOUNTING BRACKET

The typical mounting location for the FAAST XT PRO unit is on the wall. The

unit is mounted to the wall using the enclosed mounting bracket. Figure 1

shows the wall mounting bracket. For easier access to the FAAST XT PRO

unit, it is preferred to position the mounting bracket in an easily accessible

location.

1. Place the mounting bracket on the wall in the desired location and use it

as a template to locate the necessary mounting holes.

2. Mark the hole locations and remove the bracket. It is recommended to

secure the bracket using the 3 outer mounting holes.

3. Using a drill and the proper size bit for your mounting hardware, drill

the necessary holes.

4. Use appropriate fasteners to accommodate the mounting surface and

FAAST XT PRO device weight.

5. Secure the bracket to the wall.

MOUNTING THE DETECTOR TO THE BRACKET

Once the mounting bracket is attached, the unit is ready to be mounted on to

the bracket. Perform the following procedure to mount the unit.

1. Before installing the unit onto the bracket, remove the appropriate con

duit caps from the top or bottom left side of the unit to match the orien-

tation of the wiring.

2. Line up the unit with the three mounting clips and the mounting studs

on the left side.

3. Push the unit down onto the mounting clips and secure it with the sup

plied washer and nut on the mounting studs protruding through the

mounting slots shown in Figure 2.

CONNECTING THE AIR SAMPLING PIPE

ATTENTION

Detailed pipe network information and best practices can be found in the Pipe

Installation Guide, available for download at systemsensor.com/faast

The input and output ports are designed to accept nominal one inch pipe

(25mm). The input and output ports are tapered to provide fast, easy, pushfit

connection of the sampling pipe to the unit. Perform the following procedure

to connect the air sampling pipe to the unit.

1. Square off and de-burr the end of the sampling pipe. Ensure that the pipe

is free from any particles that might interfere with the pipe connection.

2. Remove the input plug from the input port being used (either the top or

bottom of the unit).

3. Insert the air sampling pipe into the port, ensuring a snug fit. DO NOT

glue these pipes.

EXHAUST PIPE

The device should always be exhausted in to the space that it is monitoring.

There are some circumstances where it may be necessary to connect a pipe to

the exhaust port to divert the exhaust away from the location of the unit. Add-

ing as little as 2ft of exhaust pipe also acts as a muffler for the fan – ensuring

quieter operation. The output ports are tapered the same as the input ports, to

provide fast, easy, push-fit connection of an exhaust pipe to the unit. Perform

the following procedure to connect the exhaust pipe to the unit.

1. Square off and de-burr the end of the exhaust pipe. Ensure that the pipe

is free from any particles that might interfere with the pipe connection.

2. Remove the plug from the exhaust port being used (either the top or

bottom of the unit).

3. Insert the air exhaust pipe into the port, ensuring a snug fit. DO NOT

glue these pipes.

FIGURE 1: WALL MOUNTING BRACKET

11.15in (28.3cm)

11.17in (28.4cm)

3.23in (8.2cm)

.300 ± .010 (.76cm ± .3cm)

ASP115-01

FIGURE 2: MOUNTING SLOTS FOR MOUNTING STUDS

ASP116-00

3 I56-6500-000

10-05

WIRING

WARNING

Before working on the FAAST XT PRO system, notify all required authorities

that the system will be temporarily out of service. Make sure all power is

removed from the system before opening the unit. All wiring must be in ac-

cordance with local codes.

POWER CABLES

Use the power ratings of the unit to determine the required wire sizes for each

connection. Use the power ratings of the connected products to determine the

wire size.

CONDUIT USAGE

If electrical conduit is used for system wiring, terminate the conduits at the

cable entry ports on the top or bottom of the unit, using the appropriate con-

duit connectors.

1. Run all wiring, both power and alarm, through the conduit and into the

left side of the unit enclosure, as seen in Figure 3.

2. Attach the appropriate wires to the supplied Euro connector. Follow

appropriate local codes and electrical standards for all cabling.

3. Plug the appropriate connector into the mating connector on the unit.

CABLING REQUIREMENTS

The FAAST XT PRO system provides a series of Euro style pluggable terminals,

located behind the left side door of the unit. Refer to Table 1 for the proper

electrical connections to the unit. Refer to Figure 4 for a typical connection for

monitoring the FAAST XT PRO system at a Fire Alarm Control Panel (FACP).

FIGURE 3. POWER AND ALARM CONNECTION BLOCK FIGURE 4. FACP WIRING DIAGRAM

TABLE 1. TERMINAL DESIGNATIONS

TERMINAL

BLOCK

External Power – Powers Aspirating Smoke Detector

Not used.

RS 485 Rx

Rx and Tx can be wired in a half duplex configuration

RS 485 Tx

Rx and Tx can be wired in a half duplex configuration

Alert Relay – Maintains state on loss of power

Action1 Relay – Maintains state on loss of power

Action2 Relay – Maintains state on loss of power

Fire1 Relay – Maintains state on loss of power

Fire2 Relay – Maintains state on loss of power

T10

Minor Fault Relay – Maintains state on loss of power

T11

Urgent Relay – Always reverts to reset on loss of power

T12

Isolate Relay – Maintains state on loss of power

T13

External Monitor

N.C.

N.O.

Fire2 Relay

Contacts

(T9)

Fire Panel (FACP) typical connection

FAAST XT

Fire Alarm Aspiration Sensing Technology®

for monitoring of device

Alarm

Short = Fire

Open = Fault

EOL

N.C.

N.O.

Fire1 Relay

Contacts

(T8)

Alarm

Short = Fire

Open = Fault

N.C.

N.O.

Action2

Relay

Contacts

(T7)

Alarm

Short = Fire

Open = Fault

N.C.

N.O.

Action1

Relay

Contacts

(T6)

Alarm

Short = Fire

Open = Fault

N.C.

N.O.

Alert Relay

Contacts

(T5)

Alarm

Short = Fire

Open = Fault

N.C.

N.O.

Isolate Relay

Contacts

(T12)

Supervisory

Short = Isolate

Open = Fault

N.C.

N.O.

Urgent Relay

Contacts

(T11)

Short = Urgent Fault

Open = Fault

N.C.

N.O.

Minor Relay

Contacts

(T10)

Short = Minor Fault

Open = Fault

FACP

Supervisory

EOL

External

Monitor

(T13)

N.C.

N.O.

(Reset)

Panel

Remote

Reset

47kΩ

ASP114-01

ASP18-24

4 I56-6500-000

System Sensor®, PipeIQ®, and FAAST Fire Alarm Aspiration Sensing Technology® are registered trademarks of Honeywell International, Inc.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installa

tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

FCC STATEMENT

System Sensor warrants its enclosed smoke detector to be free from defects in materials

and workmanship under normal use and service for a period of three years from date

of manufacture. System Sensor makes no other express warranty for this smoke detec

tor. No agent, representative, dealer, or employee of the Company has the authority to

increase or alter the obligations or limitations of this Warranty. The Company’s obligation

of this Warranty shall be limited to the repair or replacement of any part of the smoke

detector which is found to be defective in materials or workmanship under normal use

and service during the three year period commencing with the date of manufacture.

After phoning System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return

Authorization number, send defective units postage prepaid to: Honeywell, 12220 Rojas

WARRANTY

Drive, Suite 700, El Paso, TX 79936, USA. Please include a note describing the malfunc-

tion and suspected cause of failure. The Company shall not be obligated to repair or

replace units which are found to be defective because of damage, unreasonable use,

modifications, or alterations occurring after the date of manufacture. In no case shall the

Company be liable for any consequential or incidental damages for breach of this or any

other warranty, expressed or implied whatsoever, even if the loss or damage is caused by

the Company’s negligence or fault Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion may not apply

to you. This Warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

This aspiration detector does not produce any hazardous laser radiation and is certified

as a Class 1 laser product under the U.S. Department of Health and Human Services

(DHHS) Radiation Performance Standard according to the Radiation Control for Health

and Safety Act of 1968. Any radiation emitted inside the smoke detector is completely

within the protective housings and external covers.

The laser beam cannot escape from the detector during any phase of operation.

The Center of Devices and Radiological Health (CDRH) of the U. S. Food and Drug

Administration implemented regulations for laser products on August 2, 1976. These

regulations apply to laser products manufactured after August 1, 1976. Compliance is

mandatory for products marketed in the United States.

LASER SAFETY INFORMATION

The use of all FAAST products (configuration, design, use and maintenance) must be performed in accordance with the technical documentation, General Terms and Conditions and

local regulations and/or directives for design, installation and maintenance of fire alarm systems. Product Manuals, User Guides, White Papers, CAD Drawings, Datasheets, Engineering

specifications are available from www.systemsensor.com/faast. The performance of this system is dependent upon the pipe network. Any extensions or modifications to the designed

installation may cause improper operation. The operational effects of such changes shall be verified. A design tool is available from System Sensor webpage.

Class 1, Div 2 - RJ45 Connector is for maintenance use only and shall not be used while in a Hazardous Location unless power has been removed or the area is known to be non-

hazardous. These units are tested and regulatory approved to allow the pipe networks to be installed in corrosive or hostile environments. The aspiration unit itself should operate in

a controlled environment as per the specifications listed in the manual. The detector unit is not suitable to be installed in hostile environments.

Exposure of the detector to silicone vapor must be avoided as it may permanently inhibit the pipe identification sensor from detecting fire gases. Sources of silicone vapor include

furniture polish, spray lubricants, and flexible uncured gaskets and sealants.

Avoid installing the detector in areas that have elevated levels of organic chemical vapors such as alcohol, as this will affect the baseline of the channel identification sensors. Other

gases known to have an effect on MOS sensors that FAAST XT PRO uses for identifying the smoke in individual inlets, are oxidizing agents such as chlorine, ozone, nitrogen oxides.

While these gases will not permanently damage the sensors and will not have an impact on the overall smoke detection, they may impair the ability to identify the inlet affected by

smoke.

GENERAL WARNINGS

SYSTEM POWERING

The following procedure describes how to initially power up the FAAST XT PRO

system.

1. Unplug the unit’s power connector to the unit before turning on the

power.

2. Turn on the power.

3. Check the voltage at the connector. Make sure it is within the required

voltage range.

4. If wiring is not connected to the external monitor terminal, install a

47kΩ resistor (provided with the unit) into the terminal block and fit it

into the T6 terminal.

5. If the voltage is within the proper range, reconnect the power connector

to the unit.

6. Verify the system fan starts up and air begins to flow out of the exhaust

port. The user interface will provide the device status.

7. Connect a computer, with PipeIQ installed, to the unit using either the

USB connection on the front of the device, or the Ethernet port located in

the left side wiring door. (See ‘Connecting to FAAST XT PRO’ for detailed

connection instructions.)

8. Use the PipeIQ software to set up the unit configuration required for the

particular application.

9. The PC may now be disconnected unless a permanent networked con

nection is desired.

10. The device will establish an airflow baseline during the first five minutes

of operation after powering on, following the successful download of a

configuration to the device from PipeIQ, or after initiating Baseline Reset

from Functions menu on the unit’s display. During the initial baseline

period the LCD will display Baseline message.

The calculated baseline is stored in the device’s non-volatile memory and

is used to monitor changes in the system’s airflow that may be caused

my dust build up, broken piping, clogged holes, etc. Therefore, it is im

portant to verify that the system is setup and installed per the PipeIQ

design file and meets the requirement of the local codes and authorities.

The Baseline message is also displayed after power on reset, following

the initial baseline period. During the five minutes after power up the

device is monitoring the system to determine the current airflow baseline

of the system. Once the current airflow baseline is established, it is com

pared to the initial baseline stored in non-volatile memory to determine

the overall health of the system.

System Sensor FAAST XT Pro I56-6500 User manual

Brand: System Sensor

Model: FAAST XT Pro I56-6500

Category: Fire protection

Type: User manual

This manual is also suitable for

FAAST_XTPro_9440X

Download PDF

report

System Sensor FAAST XT Pro I56-6500 User manual

This manual is also suitable for

System Sensor FAAST XT Pro I56-6500 User manual

Related papers

Other documents