BenQ W1600UST User manual

Projector

User Manual

Table of contents2

Ta b l e o f c o nte n t s

Important safety

instructions ........................... 3

Introduction.......................... 7

Projector features.....................................7

Shipping contents ......................................8

Projector exterior view...........................9

Controls and functions ..........................10

Positioning your

projector..............................15

Using the quick install ............................15

Obtaining a preferred projected image

size..............................................................17

Dimensions...............................................18

Connection .........................19

Connecting video source devices........20

Connecting smart devices.....................21

Operation............................22

Starting up the projector ......................22

Adjusting the projected image .............23

Using the menus......................................24

Securing the projector...........................25

Switching input signal .............................27

Magnifying and searching for details ...28

Selecting the aspect ratio ......................29

Optimizing the image .............................31

Remote paging operations ....................34

Freezing the image ..................................34

Hiding the image......................................35

Locking control keys ..............................35

Operating in a high altitude

environment.............................................35

Adjusting the sound................................36

Using the test pattern............................ 36

Shutting down the projector ............... 37

Direct power off.....................................37

Menu operation ...................................... 38

Maintenance........................ 47

Care of the projector............................ 47

Lamp information ................................... 48

Troubleshooting ................ 54

Specifications ...................... 55

Projector specifications......................... 55

Timing chart.............................................56

Warranty and Copyright

information ......................... 60

Important safety instructions 3

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information

technology equipment. However, to ensure safe use of this product, it is important that

you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1. Please read this manual before

you operate your projector. Save

it for future reference.

2. Do not look straight at the

projector lens during operation.

The intense light beam may damage

your eyes.

3. Refer servicing to qualified

service personnel.

4. Always open the lens shutter (if

any) or remove the lens cap (if

any) when the projector lamp is

on.

5. In some countries, the line voltage is

NOT stable. This projector is

designed to operate safely within a

mains voltage between 100 to 240

volts AC, but could fail if power cuts

or surges of ±10 volts occur. In

areas where the mains voltage

may fluctuate or cut out, it is

recommended that you connect

your projector through a power

stabilizer, surge protector or

uninterruptible power supply

(UPS).

6. Do not block the projection lens with

any objects when the projector is

under operation as this could cause

the objects to become heated and

deformed or even cause a fire. To

temporarily turn off the lamp, press

ECO BLANK on the projector or

remote control.

Important safety instructions4

Safety Instructions (Continued)

7. The lamp becomes extremely hot

during operation. Allow the projector

to cool for approximately 45 minutes

prior to removing the lamp assembly

for replacement.

8. Do not operate lamps beyond the

rated lamp life. Excessive operation of

lamps beyond the rated life could

cause them to break on rare

occasions.

9. Never replace the lamp assembly or

any electronic components unless the

projector is unplugged.

10. Do not place this product on an

unstable cart, stand, or table. The

product may fall, sustaining serious

damage.

11. Do not attempt to disassemble this

projector. There are dangerous high

voltages inside which may cause death

if you should come into contact with

live parts. The only user serviceable

part is the lamp which has its own

removable cover.

Under no circumstances should you

ever undo or remove any other

covers. Refer servicing only to

suitably qualified professional service

personnel.

12. When the projector is under

operation, you may sense some

heated air and odor from its

ventilation grill. It is a normal

phenomenon and not a product

defect.

Important safety instructions 5

Safety Instructions (Continued)

13. Do not place this projector in any of

the following environments.

- Space that is poorly ventilated or

confined. Allow at least 50 cm

clearance from walls and free flow of air

around the projector.

- Locations where temperatures may

become excessively high, such as the

inside of a car with all windows rolled

up.

- Locations where excessive humidity,

dust, or cigarette smoke may

contaminate optical components,

shorten the projector's life span and

darken the image.

- Locations near fire alarms

- Locations with an ambient temperature

above 40°C / 104°F

- Locations where the altitudes are higher

than 3000 m (10000 feet).

14. Do not block the ventilation holes.

- Do not place this projector on a

blanket, bedding or any other soft

surface.

- Do not cover this projector with a cloth

or any other item.

- Do not place inflammables near the

projector.

If the ventilation holes are seriously

obstructed, overheating inside the

projector may result in a fire.

15. Always place the projector on a level,

horizontal surface during operation.

- Do not use if tilted at an angle of more

than 10 degrees left to right, nor at

angle of more than 15 degrees front to

back. Using the projector when it is not

fully horizontal may cause a malfunction

of, or damage to, the lamp.

16. Do not stand the projector on end

vertically. Doing so may cause the

projector to fall over, causing injury or

resulting in damage to the projector.

3000 m

(10000 feet)

0 m

(0 feet)

Important safety instructions6

Safety Instructions (Continued)

17. Do not step on the projector or place

any objects upon it. Besides probable

physical damage to the projector, doing

so may result in accidents and possible

injury.

18. Do not place liquids near or on the

projector. Liquids spilled into the

projector may cause it to fail. If the

projector does become wet,

disconnect it from the power supply's

power outlet and call BenQ to have

the projector serviced.

19. This product is capable of displaying

inverted images for ceiling mount

installation.

Use only BenQ's Ceiling Mount Kit for

mounting the projector and ensure it is

securely installed.

20. This apparatus must be earthed.

Ceiling mounting the projector

We want you to have a pleasant

experience using your BenQ projector,

so we need to bring this safety matter

to your attention to prevent possible

damage to person and property.

If you intend to mount your projector

on the ceiling, we strongly recommend

that you use a proper fitting BenQ

projector ceiling mount kit and that

you ensure it is securely and safely

installed.

If you use a non-BenQ brand projector

ceiling mount kit, there is a safety risk

that the projector may fall from the

ceiling due to an improper attachment

through the use of the wrong gauge or

length screws.

You can purchase a BenQ projector

ceiling mount kit from the place you

purchased your BenQ projector. BenQ

recommends that you also purchase a

separate Kensington lock compatible

security cable and attach it securely to

both the Kensington lock slot on the

projector and the base of the ceiling

mount bracket. This will perform the

secondary role of restraining the

projector should its attachment to the

mounting bracket become loose.

Hg - Lamp contains mercury. Manage in

accordance with local disposal laws. See

www.lamprecycle.org.

Introduction 7

Introduction

Projector features

The projector offers the following features

• SmartEco™ starts your dynamic power saving

The SmartEco™ technology offers a new way of operating the projector lamp system

and saves lamp power depending on the content brightness level.

• HDMI/MHL compatible

You can project the content from your smart devices via HDMI/MHL connection.

• Less than 0.5W in standby condition

Less than 0.5W power consumption under standby mode.

• One-key auto-adjustment

Pressing AUTO on the keypad or remote control to show the best picture quality

immediately.

• Built-in 10 W x 2 speaker(s)

Built-in speaker(s) providing mixed mono audio when an audio input is connected

• Quick Cooling, Auto Power Off, Signal Power On, Direct Power On

Quick Cooling function speeds up the cooling process when turning off the

projector. Auto Power Off function allows the projector to turn off automatically if

no input signal is detected after a set period of time. Signal Power On function turns

on your projector automatically once detecting the signal input and Direct Power

On turns your projector when the power is fed.

• 3D Function supported

Various 3D formats make the 3D function more flexible. By presenting the depth of

the images, you can wear BenQ 3D glassed to enjoy the 3D movies, videos and

sporting events in a more realistic way.

• The apparent brightness of the projected image will vary depending on the ambient lighting conditions,

selected input signal contrast/brightness settings, and is directly proportional to projection distance.

• The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This

is normal and expected behavior.

Introduction8

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items

are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those illustrated.

*Only supplied in some specific regions. Please consult your dealer for detailed information.

Optional accessories

Projector Power cord Remote control with

batteries

Quick start guide User manual CD Warranty card*

Digital Projector

Quick Start Guide

1. Spare lamp kit

2. 3D glasses

Introduction 9

Projector exterior view

1. Lamp cover

2. Vent (heated air exhaust)

3. Speaker

4. Front IR remote sensor

5. Projection lens and Mirror

6. Adjuster foot

7. Speaker

8. External control panel

(See "Controls and functions" on

page 10 for details.)

9. Focus ring

10. Vent (cool air intake)

11. AC power jack

12. HDMI-input port

13. HDMI/MHL-input port

14. Audio (L/R) input jacks

15. Video input jack

16. Audio input jacks

17. RGB (PC)/Component Video (YPbPr/

YCbCr) signal input jacks

18. Audio output jack

19. RS232 control port

20. USB Mini-B port (Used for service.)

21. Kensington anti-theft lock slot

a

b

4

5

9

10

6

7

8

2

1

3

Front/upper side

21

11

6 6

13 15 20

1912 14

17

1816

Rear/lower side

Introduction10

Controls and functions

Projector

1. LAMP indicator light

Indicates the status of the lamp. Lights up

or flashes when the lamp has developed a

problem.

2. TEMPerature warning light

Lights up red if the projector's

temperature becomes too high.

3. POWER indicator light

Lights up or flashes when the projector is

under operation.

4. Focus ring

Adjusts the focus of the projected image.

5. Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images

resulting from an angled projection.

6. SOURCE

Displays the source selection bar.

7. Left/

Decreases the projector volume.

8. AUTO

Automatically determines the best picture

timings for the displayed image.

9. POWER

Toggles the projector between standby

mode and on.

10. ECO BLANK

Used to hide the screen picture.

11. MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display

(OSD) menu item.

12. Right/

Increases the projector volume.

When the On-Screen Display (OSD)

menu is activated, the #5, #7 and #12

keys are used as directional arrows to

select the desired menu items and to

make adjustments.

13. MENU/EXIT

Turns on the On-Screen Display (OSD)

menu. Goes back to previous OSD menu,

exits and saves menu settings.

a

b

1 2 3

4

5

6

7

8

9

10

11

12

13

5

Introduction 11

Remote control

1. ON/ OFF

Toggles the projector between standby

mode and on.

2. Source selection buttons

(COMPUTER 1, COMPUTER 2,

VIDEO, HDMI

)

Selects an input source for display.

Source selection button (HDMI

)

Selects the HDMI or HDMI/MHL input

signal for display.

3. Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images

resulting from an angled projection.

4. MENU/EXIT

Turns on the On-Screen Display (OSD)

menu. Goes back to previous OSD menu,

exits and saves menu settings.

5. Left/

Decreases the projector volume.

6. MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display

(OSD) menu item.

7. ECO BLANK

Used to hide the screen picture.

8. LASER

Emits visible laser pointer light for

presentation purposes.

9. MHL control buttons

(Previous, Play/Pause,

Next, Rewind, Stop,

Fast-forward)

Goes to the previous file/Plays/Pauses/

Goes to the next file/Rewinds/Stops/Fast-

forwards during media playback.

Only available when controlling your smart

device in MHL mode.

10. ZOOM+/ZOOM-

Magnifies or reduces the projected picture

size.

11. PAGE+/PAGE-

Operate your display software program

(on a connected PC) which responds to

page up/down commands (like Microsoft

PowerPoint).

2

3

4

8

9

11

12

13

14

10

6

5

7

1

17

21

22

23

24

18

15

16

19

3

20

Introduction12

12. FREEZE

Freezes the projected image.

13. NETWORK SETTING

(No function.)

14. QUICK INSTALL

Quickly selects several functions to adjust

the projected image and displays the test

pattern.

15. NETWORK

(No function.)

16. S-VIDEO

(No function.)

17. AUTO

Automatically determines the best picture

timings for the displayed image.

18. Right/

Increases the projector volume.

When the On-Screen Display (OSD) menu

is activated, the #3, #5, and #18 keys are

used as directional arrows to select the

desired menu items and to make

adjustments.

19. SOURCE

Displays the source selection bar.

20. VOL+/VOL-

Adjusts the projector volume.

21. MUTE

Toggles projector audio between on and

off.

22. ASPECT

Selects the display aspect ratio.

23. SMART ECO

Displays the Lamp Mode

menu for

selecting a suitable lamp operating mode.

24. Numeric buttons

(No function.)

Operating the LASER pointer

The Laser Pointer is a

presentation aid for

professionals. It emits red

colored light when you press it.

The laser beam is visible. It is

necessary to press and hold

LASER for continuous output.

Do not look into the laser light

window or shine the laser light beam on yourself or

others. See the warning messages on the back of the

remote control prior to using it.

The laser pointer is not a toy. Parents should be

mindful of the dangers of laser energy and keep

this remote control out of the reach of children.

Introduction 13

Controlling your smart device with the remote control

When the projector projects the content from your MHL compatible smart device, you

can use the remote control to control your smart device.

To enter the MHL mode, press and hold AUTO for 3 seconds. The following buttons are

available for controlling your smart device: Arrow keys ( / Up, / Down,

Left, Right), MENU/EXIT, MODE/ENTER, #0-#9, MHL control buttons.

To leave the MHL mode, press and hold AUTO for 3 seconds.

When the projector is under MHL mode, the keypad on the projector should be with the same definition of

the keys on the remote control.

Remote control effective range

The remote control must be held at an angle within 30 degrees perpendicular to the

projector's IR remote control sensor(s) to function correctly. The distance between the

remote control and the sensor(s) should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor(s) on

the projector that might obstruct the infra-red beam.

• Operating the projector from the front

A

p

r

o

x

.

+

3

0

º

Introduction14

Replacing the remote control batteries

1. To open the battery cover, turn the remote control over to view its back, push on

the finger grip on the cover and slide it up in the direction of the arrow as illustrated.

The cover will slide off.

2. Remove any existing batteries (if necessary) and install two AAA batteries observing

the battery polarities as indicated in the base of the battery compartment. Positive

(+) goes to positive and negative (-) goes to negative.

3. Refit the cover by aligning it with the base and sliding it back down into position. Stop

when it clicks into place.

• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the

kitchen, bathroom, sauna, sunroom or in a closed car.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

• Dispose of the used batteries according to the manufacturer's instructions and local environment

regulations for your region.

• Never throw the batteries into a fire. There may be danger of an explosion.

• If the batteries are dead or if you will not be using the remote control for an extended period of time,

remove the batteries to avoid damage to the remote control from possible battery leakage.

Positioning your projector 15

Positioning your projector

Using the quick install

The projector provides a hot key to set Test Pattern, Projector

Installation, and Keystone quickly.

Press QUICK INSTALL on the remote control and press /

to select from the below items:

• Projector Installation. See "Positioning your projector" on

page 15 for details.

• Test Pattern. See "Using the test pattern" on page 36 for details.

• Keystone. See "Correcting keystone" on page 23 for details.

1. Choosing a location

Your projector is designed to be installed in one of the following possible installation

locations:

2. Using the test pattern

Quick Install

Test Pattern

Projector Installation

Keystone

Exit

Front Table

Rear Table

Positioning your projector16

3. Correcting the image

• Keystone correction

Set up your screen via the QUICK INSTALL hotkey on the remote control. You can

also go to the SYSTEM SETUP: Basic > Projector Installation menu after turning on

the projector. See "Using the menus" on page 24 on how to use the OSD menu.

Your room layout or personal preference will dictate which installation location you select.

Take into consideration the size and position of your screen, the location of a suitable

power outlet, as well as the location and distance between the projector and the rest of

your equipment.

Positioning your projector 17

Obtaining a preferred projected image size

Projection dimensions

• Installation distance D is measured from the projector rear side to the wall surface.

• Projection distance a is measured from the projector rear side to the projection surface.

• Vertical offset V is measured from the top edge of the front of the projector to the bottom edge of

screen.

The screen aspect ratio is 16:9 and the projected picture is in a 16:9 aspect ratio

Screen size

Ver t ic a l

offset

Installation distance (D)

Diagonal (M) Height (h) Width (W) V

X

a

=0 mm

(D=a)

a. Assume the thickness of projection screen(X) is 0 mm.

X

b

=30 mm

(D=a+30 mm)

b. Assume the thickness of projection screen(X) is 30 mm.

Inch mm (mm) (mm) (mm) (mm) (mm)

87 2210 1083 1926 177 83 113

90 2286 1121 1992 185 98 128

95 2413 1183 2103 196 122 152

100 2540 1245 2214 208 147 177

105 2667 1308 2324 220 171 201

110 2794 1370 2435 232 196 226

115 2921 1432 2546 244 221 251

120 3048 1494 2657 256 245 275

125 3175 1557 2767 267 270 300

130 3302 1619 2878 279 295 325

a

D

V

M

W

h

X

Thickness of the screen

Positioning your projector18

All measurements are approximate and may vary from the actual sizes.

BenQ recommends that if you intend to permanently install the projector, you should physically test the

projection size and distance using the actual projector in situ before you permanently install it, so as to make

allowance for this projector's optical characteristics. This will help you determine the exact mounting position

so that it best suits your installation location.

Dimensions

385.5

429.2

152.6

Unit: mm

126.6

152.6

429.2

Connection 19

Connection

When connecting a signal source to the projector, be sure to:

1. Turn all equipment off before making any connections.

2. Use the correct signal cables for each source.

3. Ensure the cables are firmly inserted.

• In the connections shown below, some cables may not be included with the projector (see "Shipping

contents" on page 8). They are commercially available from electronics stores.

• The connection illustrations below are for reference only. The rear connecting jacks available on the

projector vary with each projector model.

5 3 1

2

5

7

6

4

7

Notebook or desktop computer

Speakers

A/V device

Smartphone

or tablet PC

or

Connection20

Many notebooks do not turn on their external video ports when connected to a projector. Usually a key

combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD

or a function key with a monitor symbol on the notebook. Press FN and the labeled function key

simultaneously. Refer to your notebook's documentation to find your notebook's key combination.

Connecting video source devices

You need only connect the projector to a video source device using just one of the

connecting methods, however each provides a different level of video quality. The method

you choose will most likely depend upon the availability of matching terminals on both the

projector and the video source device as described below:

Connecting audio

The projector has built-in mono speaker(s) which are designed to provide basic audio

functionality accompanying data presentations for business purposes only. They are not

designed for, nor intended for stereo audio reproduction use as might be expected in

home theater or home cinema applications. Any stereo audio input (if provided), is mixed

into a common mono audio output through the projector speaker(s).

The built-in speaker(s) will be muted when the AUDIO OUT jack is connected.

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See

"Connecting audio" on page 20 for details.

• If the selected video image is not displayed after the projector is turned on and the correct video source

has been selected, check that the video source device is turned on and operating correctly. Also check

that the signal cables have been connected correctly.

1. VGA cable

2. USB cable

3. Component Video to VGA (D-Sub)

adapter cable

4. Video cable

5. Audio cable

6. Audio L/R cable

7. HDMI cable

Te r m i n a l n a m e Terminal appearance Picture quality

HDMI

HDMI/MHL

Best

Component Video Better

Video Normal

Page is loading ...

BenQ W1600UST User manual

BenQ W1600UST User manual

Related papers

Other documents