Pyle PLR18MPF User manual

Pyle
Brand
Pyle
Model
PLR18MPF
Type
User manual
www.pyleaudio.com
PLRIBMPF
I.Control
Panel
1I.0peration
1.Next button
1.
Next button
2.
Play/Pause button
3.
Volume knob
4.
Display
5.Time controls
6.
Auto scan button
7.Tunerknob
8.
Prevo
button
9.
Power switch
10.
SD
/
MMC
card slot
11
.
USB
interface
12.
Mode
switch
13.
Band
button
In
USB/SD/MMC playing state, press this button to
select
and play next track,
or
press
and hold this button to select and play
+10 latter tracks.
In
radio state, press this
buttonto select and play next channel.
2.Play/Pause button
In
USB
or
SD/MMC playing state, press this button to pause and press it again to
resume playing.
In
radio state, select desired channel with the
tuner
knob and press
this button to save the channel (up to 18 channels can be saved).
3.volume
knob
Rotate this knob to adjust the volume.
4.Display
Display radio frequency
or
playing info.
5.Time controls
To
adjust the hour, press and hold the H key, and then press the H key to
adjust
the
value when the hour value flashes; to
adjust
the minute, press and hold the M key, and
then press the M key to
adjust
the value when the minute value flashes.
After
adjus
tment,
wait
for
several seconds and the radio
or
playing status bar will resume.
6.Auto scan button
In
radio state, press and hold this button to scan and store channel automatically until
the three
FM
bands are saved completely. Press and hold this key to view the saved
1.
Channels. When the signal from desire channel is received, press this button again to
listen to the program.
7 .Tuner knob
In
radio state, rotate the knob to
left/right
to scan radio channels automatically
or
manually.
8.Prev. button
In
USB/SD/MMC playing state, press this button to
select
and play previous track,
or
press and hold it to
select
and play
-1
0 previous tracks. In radio state, press this button
to
select
and play previous channel.
9.Power switch
Press this button to turn on the device and press it again to turn off.
10.SD/MMC card
slot
Insert SD/MMC card and play the tracks automatically.
11.USB interface
Insert USD
disk
and play the tracks automatically.
12.Mode switch
Press the
MOD button to switch mode.
If
USB
disk
and SD/MMC card are connected to
the device, press the
MOD button to switch in this sequence: USB, SD/MMC, radio;
if
only USB
disk
or
SD/MMC card is connected, press the MOD button to switch between
available modes;
if
both USB
disk
and SD/MMC card are not connected, MOD button is
invalid.
13.Band button
In
radio state, press this button to
select
the band.
III.Technical parameters
FMTUNER
Tu
n i ng
ra
ng
e:
--
-----------------------------------------------------------------8
7.5 M Hz
-1
08 MHz
I ntermed iate frequency: ------------------------------------------------------------------10.
7M
Hz
S N R: --------------------------------------------------------------------------------------------= 5 0 d B
AMTUNER
Tu
ni ng range -------------------------------------------------------------------------530-171 OKHz
Usa b
lese
n sit i v ity
------------------------------------------------------------------------------
3 8 d B
Playing:
S N R:
-------------------------------------------------------------------------------------------
;:, 50d B
C han nel isol atio n (at 1 kHz): --------------------------------------------------------------- ;:, 2 3d B
Harmonic distortion (at 1 kHz):
--------------------------------------------------------------
:::;
5%
Frequency response:
-----------------------------------------------------(
100
Hz-10kHz)
± 6d B
Power amplifier:
Out put: ------------------------------------------------------------------------------- S pe a k e r 0 u tp u t
S pea ke
rim
peda n ce:
------------------------------------------------------------------------4
Q--8 Q
Maximum output power: -----------------------------------------------------5OWX4(200Watts)
Power
supply:---------------------------------------------------------------
12V DC car batteries
IV.lnstaliation diagram
1.Before installing the master unit, put it in the proper position, and connect the
speaker
wire and power cord.
2.1f
the master unit runs normally, fix it.
2.
Fixing
flake
\
Stand
-
Double-head
screw
/
/
Disassembly
key
IInstalling the master unit
~
1.lnstall the bracket on the dashboard
of
the vehicle, and bend the stand.
2.Connect the power cord and speaker wire, and fix the fixing flake on the vehicle.
3.lnsert the antenna plug, push the master unit into the stand and fasten the fixing nuts.
LUninstaliing the master unit
Remove the fixing nuts, insert the two disassembly keys into the gaps on the left and
right sides, hook the master unit with the keys and
pull out lightly. Then, pull
out
the
antenna plug and remove the power cord and speaker wire.
V.Wiring diagram
To
Automatic Blue
Antenna
_"":::=_...J
Left
Speaker
Left
Speaker
+
White
_Whitewith
black
strip
+
Green
_
Green
with
black
strip
3.
Black
To
Battery
+
To
Ignition
Switch
'--
____
To Battery-
Grey
+
Grey
with-
black
strip
Violet
+
Violet
with
-
black
strip
Right
Speaker
Right
Speaker
VI.Precautions
Only replace the fuses of same specification.
VII.Troubleshooting
Failure
Reason
Solution
Can't
start
thedevice
The
fuse
is
melt
Replace
with
same
fuse
No
memory
Ignition
wire
and
anode
power
Reconnect
the
wire.
cord
are
not
connected
properly
The
vehicle
antenna
isn't
Check
whether
the
control
wire
of
automatic
radio
antenna
is
Weak
radio
signal
stretched
out
,
connected
properly;
check
Poor
antenna
grounding
whether
antenna
and
ground
wire
are
connected
properly
Can't
read
SO
card
SO
card
is
inserted
reversely
or
damaged
Turn
over
or
replace
the
SO
card
The
connection
is
improper
Check
and
correct
the
connection
No audio or low volume
Speaker
is
connected
to
ground
Connect
the
speaker
to
the
cathode
of
power
amplifier
output
Note: The specifications are subject to changes without prior notice.
4.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Pyle PLR18MPF User manual

Pyle
Brand
Pyle
Model
PLR18MPF
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents