Vision Fitness R2250 Frame 9 User manual

1

BECS_9 Service manual

(E3200 Frame_9/E1500 Frame_9/R2250 Frame_9/

R1500 Frame_9/X6200 Frame_9/X1500 Frame_9/

X20 Frame_09)

2

TABLE OF CONTENTS

CHAPTER 1: SERIAL NUMBER LOCATION……………………………..….……….3

CHAPTER 2: CONSOLE INSTRUCTION

2.1 CONSOLE HARDWARE DESCRIPTIONS …………………………….………….……4

2.2 SIMPLE CONSOLE DESCRIPTIONS…………………………………………………...5

2.3 USE THE SIMPLE CONSOLE……………………………………………………………5

CHAPTER 3: ENGINEERING MODE

3.1 ENGINEERING MODE………………………………………………………….…….…..6

CHAPTER 4: ELECTRON DIAGRAMS

4.1 RB130-2KM-C(BECS_9) …..………………………………………………….….……..8

4.2 CB142B-2KM-F(E3200 FRAME_9) …….…………………………………….….……..9

4.3 CB143-2KM-F(E1500 FRAME_9) …..….…………………………………….….…….10

4.4 RB135-2KM-F(R2250 FRAME_9) …..….…………………………………….….…….11

4.5 RB133-2KM-F(R1500 FRAME_9) …..….…………………………………….….…….12

4.6 EP225-2KM-F(X6200 FRAME_9) …..….…………………………………….….…….13

4.7 EP224-2KM-F(X1500 FRAME_9) …..….…………………………………….….…….14

4.8 EP240-2KM-F(X20 FRAME_9) …..….…………………………………….….………..15

CHAPTER 5 ERROR CODE

5.1 E1: NO CONNECT ECB MOTOR..….…………………………………….….….……..15

CHAPTER 6: TROUBLESHOOTING

6.1 TROUBLESHOOTING – NO RPM…………..…………………………….….………...15

6.2 TROUBLESHOOTING – RESISTANCE INACCURATE……………………………...17

6.3 TROUBLESHOOTING - NO POWER TO THE CONSOLE….…………......….…….18

3

CHAPTER 1 SERIAL NUMBER LOCATION

1.1 Serial Number Location (E3200 Frame_9/E1500 Frame_9/R2250 Frame_9/

R1500 Frame_9/X6200 Frame_9/X1500 Frame_9/X20 Frame_09)

Serial Number Placement

4

CHAPTER 2 CONSOLE INSTRUCTION

2.1 CONSOLE HARDWARE DESCRIPTIONS

A. POWER SWITCH

Turn off power to your console if it will not be used for an extended period of time.

B. MILES/KILOMETER SWITCH

Changes your exercise feedback to the English or Metric system.

C. ENTER KEY

Use this key in setup mode to select your program, exercise time, and resistance level.

D.START/PAUSE/HOLD RESET KEY

Press the START key to begin exercising in manual mode at the set default time. When

exercising, press the START key to pause your workout. To reset press and hold the

START key for three seconds.

E. UP▲OR DOWN▼ARROWS

Use these keys to change program number, exercise time, and resistance level in setup.

During the workout use these keys to increase or decrease resistance.

5

2.2 SIMPLE CONSOLE DESCRIPTIONS

A. PROFILE DISPLAY

This window provides an 8x12 block profile of your

program profile. Each horizontal row of blocks

represents your segment time, which is total workout

time divided by twelve. Each vertical column of blocks

represents the resistance level, which is one block for

every two levels.

B. FEEDBACK DISPLAY

During your workout these windows display exercise

feedback about your workout including:

-PROGRAM: A number that represents one of seven program profiles that the console

may be set to

-LEVEL: the current resistance level of your workout

-RPM: Revolutions Per Minute (RPM)

-TIME: the time elapsed or time remaining in your workout

-DISTANCE: the total distance traveled in miles or kilometers since the start of the

workout

-HEART RATE: displays your heart rate in beats per minute when using the hand pulse

grips

-CALORIES: an estimate of calories burned since the start of the workout

-WATTS: a measurement of workload. It is determined by resistance level and stride

rate

2.3 USE THE SIMPLE CONSOLE

QUICK START

The quickest and easiest way to begin exercising is to

simply press START. You will begin exercising in manual

mode for a default time at the default resistance level. You

can change the resistance manually with the arrow keys.

CHOOSING A PROGRAM

The default program number will be flashing in the

PROGRAM window. Press the UP▲ or DOWN▼ keys to

scroll through the seven program profile options. Press the

ENTER key to select a program.

6

CHOOSING EXERCISE TIME

The default exercise time will be flashing in the TIME

window. Use the UP▲ or DOWN▼ keys to set your desired

workout time. Press ENTER to select.

CHOOSING RESISTANCE LEVEL

The default resistance level will be flashing in the LEVEL

window. Use the UP▲ or DOWN▼ keys to set your desired

workout resistance level. Press ENTER to select.

CHAPTER 3 ENGINEERING MODE

3.1 ENGINEERING MODE

1) To enter Engineering Mode, press & hold the resistance UP▲ or DOWN▼ keys at the

same time for 3-5 seconds until Engineering mode(Eng1 first) appears on the display.

2) Use the resistance UP▲ or DOWN▼ keys to select a parameter.

3) Press ENTER to enter a parameter setting.

4) Press the START key to save the change to the parameter.

5) Press and hold the START key to exit Engineering Mode and return to normal operation.

7

Mode Function Description

Eng 1 Display Test

STARTÆ LED on (Fig. A)

STARTÆ LED off (Fig. B)

START ÆSTARTÆ“▲”/ “▼” Ædisplay on window

Hold “START” 3 secÆ back to “Engineering Menu”

Eng 2 Machine Test

START Æ Heart rate, Accumulated Time/Distance to be

presented on the console.

Hold “ENTER” 2 secÆ Delete the accumulated data.

Hold “START” 3 sec back to “Engineering Menu”

Eng 3 Software Version

Software version is presented.

Hold “START” 3 sec back to “Engineering Menu”

Eng 4

Default Time

Setting ( from 0 to

99 min)

Press UP▲ to increase ,

Press DOWN ▼ to decrease,

Hold ENTER 2 sec to save new setting,

Press START back to “Engineering Menu”.

Eng 5

Default Level

Setting (From L1

to L16)

Press UP▲ to increase ,

Press DOWN ▼ to decrease,

Hold ENTER 2 sec to save new setting,

Press START back to “Engineering Menu”.

Eng 6

Product Selection

& Model

Configuration

Press the UP▲ or DOWN▼ keys to select EP or Bike.

Press the ENTER key to save the change to the parameter.

Press the UP▲ or DOWN▼ keys to select model number，

Press the ENTER key to save the change. (Fig. C)

Additional Switch Function

Switch “SW2” at the back of PCB to adjust Mile and KM.

Adjust it up Æ to be Mile

Adjust it down Æ to be KM (Fig. D)

(Fig.A) (Fig.B)

(Fig C) (Fig D)

8

CHAPTER 4 ELECTRON DIAGRAMS

4.1 RB130-2KM-C(BECS_9)

9

4.2 CB142B-2KM-F(E3200 FRAME_9)

10

4.3 CB143-2KM-F(E1500 FRAME_9)

11

4.4 RB135-2KM-F(R2250 FRAME_9)

12

4.5 RB133-2KM-F(R1500 FRAME_9)

13

4.6 EP225-2KM-F(X6200 FRAME_9)

14

4.7 EP224-2KM-F(X1500 FRAME_9)

15

4.8 EP240-2KM-F(X20 FRAME_9)

CHAPTER 5 ERROR CODE

5.1 E1: No connect ECB motor

CHAPTER 6 TROUBLESHOOTING

6.1 No RPM

Reason：

1. Bad connection between the console wire and the console

2. Speed Sensor wire is defective.

3. Speed Sensor Assembly Un-properly.

4. Loss magnet from the pulley

5. Console wire is defective

6. Console defective

16

Solution：

1. Re-connect the console wire

2. Check if the speed sensor wire works. Enter Engineering Mode (See Chapter 3), and scroll

to ENG 2 (Machine Test).Press the key “ENTER”, and then pedal the machine.

- If the left 8 blocks are flashed (Fig. E), the speed sensor works well.

- If the left 8 blocks are not flashed, the speed sensor wire is defective or it is not

well-assembled. Replace the sensor speed wire if it is defective.

(Fig. E)

3. Check the gap between speed sensor and the magnet on the pulley. It is normal within 5mm

(Fig. F). Adjust it if the gap is too big.

(Fig. F)

4. Re-install a new magnet(Fig. G) if it is missed from the pulley.

(Fig. G)

17

5. Use a multi-meter to check if the console wire is conductive. If not, the console wire is

defective, and replace it.

6. Replace the console set if all above can not resolve the issue. .

6.2 Resistance Inaccurate

Reason：

1. The console cable or the console or ECB motor is defective.

2. The steel cable location is not correct or ECB motor is not assembled properly.

3. The magnetic control equipment is defective.

Solution：

1. Check if the ECB motor works. Enter Engineering Mode (See Chapter 3), and scroll to ENG

2 (Machine Test).Press the key “ENTER” first, and then press the resistance UP▲ or

DOWN▼ keys . The left window display the rounds of ECB motor moving.

- If the figure is up or down, the ECB motor works well.

- If it is always “0”, the ECB motor or the wiring is defective. Replace the ECB motor if it is

defective.

(Fig. H)

2. A. Inside Magnetic Brake Control system: Check the gap between the orange block and the

bottom. The distance shall be within 1-2 mm. If the gap is bigger than 1-2 mm, adjust the

steel cable to the correct gap range. (Fig. I) 、(Fig. J)

(Fig. I)

Inside Magnetic Brake

Control system:

RPM

18

(Fig. J)

B: Outside Magnetic Brake Control System: Adjust the resistance to the max. The distance

between the magnets and the pulley shall be 1.8-2mm. If the distance is not in this range,

adjust it to the proper position by moving the two screws at the frame. (Fig. K)

(Fig. K)

3. If the console wire & the console & the ECB motor all work well, the magnetic brake control

equipment is defective. Replace it.

6.3 No Power to the Console

Symptom: The adaptor and power switch is in the on position, but the console will not turn on.

Reason:

1. The Adaptor is defective.

2. The console wire is defective.

3. The console is defective.

Solution:

Adjust the steel cable

Distance away from magnets :

1.8~2.0mm

Adjusted screws at the

frame

19

1. Check if the LED at the adaptor is lit. If it is not, try a different outlet. (Fig. L)

- If the LED is still not lit with a known good outlet, the adaptor is defective and replace it.

(Fig. L)

Check if the power switch works. Use a multi-meter to check the negative and positive of

power switch. If the multi meter displays output DC 12V, then the power switch is good. If it

is not, the power switch is defective and replace it. (Fig. M)

(Fig. M)

2.Remove the console cable from the PCB, and use a multi-meter to measure the output DC

voltage of the console cable( pin GND and PIN VCC). If it is not output DC 12V, the console

cable is defective and replace it. (Fig. N)、(Fig. O)

(Fig. N)

20

(Fig. O)

3.If the console cable is good and the console is still not lit, the PCB is defective and replace

the console.

Vision Fitness R2250 Frame 9 User manual

This manual is also suitable for

Vision Fitness R2250 Frame 9 User manual

Related papers

Other documents