SICK Ready for explosive atmospheres Product information

Brand: SICK

Model: Ready for explosive atmospheres

Type: Product information

PRODUCT INFORMATION

READY FOR EXPLOSIVE ATMOSPHERES

EX II 2GD AND EX II 3GD

Safety light curtains, multiple light beam safety devices

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

Overview

SAFE PRODUCTIVITY –

EVEN IN EXPLOSION-HAZARDOUS AREAS

In industries with explosion-hazardous areas, a single spark can be disastrous.

The protective devices used in these environments must therefore be particularly

rugged and reliable in order to meet the strict explosion protection requirements.

When ammable gases, vapors and dusts are

combined with oxygen in a particular mix ratio,

they become explosive.

To ensure there are no ignition sources present

when protecting hazardous areas, only explosion

proof protective devices must be used.

IGNITION SOURCES

Sparks, ames,

hot surfaces,

electronic devices, etc.

OXYGEN

FLAMMABLE

SUBSTANCES

Dusts, gases, steam, etc.

READY FOR EXPLOSIVE ATMOSPHERES | SICK8024285/2019-07-23

Subject to change without notice

Overview

Certication according to international safety standards

Classication of explosion hazard

Probability of a ammable

substance occurring under

normal operating conditions

Responsible

1999/92/EC

Ex zone: Area in which

explosive atmospheres

could occur

Operating entity

2014/34/EU

Device category (ATEX)

and device protection level

EPL (IEC Ex)

Exists all of the time, for long

periods or often

Exists occasionally

Unlikely to exist or

occurs only infrequently

or temporarily

Zone 0 (gases)

Zone 20 (dusts)

Zone 1 (gases)

Zone 21 (dusts)

Zone 2 (gases)

Zone 22 (dusts)

1 G/D (gases/dusts)

Highest level of protection

with a very high degree of

safety

2 G/D (gases/dusts)

Increased level of protection

with a high degree of safety

3 G/D (gases/dusts)

Normal level of protection

with the required degree of

safety

Sensor manufacturer

For the structure of the

Ex variants from SICK,

see page 4

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

Classication

SAFETY, EVEN IN EXTREME CONDITIONS

As a global leader in the supply of opto-electronic protective devices, SICK has been eectively protecting

humans and work environments for more than 65 years. Due to its versatile application possibilities, the

deTec safety light curtain in particular is making a considerable contribution to ensuring safe productivity

in nearly all industries and areas of application.

Ex II 3GD

For gases (G) and dust (D)

Device category (ATEX) 3

Equipment group II

Explosion-proof

Ex II 2GD

For gases (G) and dust (D)

Device category (ATEX) 2

Equipment group II

Explosion-proof

Limiting explosions

3GD

Featuring a rugged and reliable housing design, the 3GD

variants are specially designed and approved for use under

the strict safety requirements found in hazardous locations.

All devices can be cascaded, enable space-saving machine

design and oer very high exibility as there are no blind

zones. A standardized connection and accessory concept

saves time and money during commissioning.

2GD

The SICK devices in their explosion-proof enclosures are

approved in accordance with ATEX, IECEx and NEC. Pre-wired

and fully mounted in the housing, the complete system is also

UL-certied and represents a truly outstanding product that is

unique on the market up to now.

The deTec safety light curtains are ideal for the protection

of hazardous areas, entrances, and hazardous points.

Shorter downtimes and therefore higher productivity

can be achieved thanks to the extensive and innovative

diagnostic options. The standardized connectivity and the

compatible accessories for the entire deTec product family

considerably reduce conguration eort and enable quick

commissioning. The required functions can be activated

without software using the appropriate system plug with

M12 connection.

Depending on the application, dierent Ex zones can be

operated with the explosion-proof variants from the deTec

product family.

READY FOR EXPLOSIVE ATMOSPHERES | SICK8024285/2019-07-23

Subject to change without notice

Customer benets

THESE ADVANTAGES IGNITE

Save time and money

• Easy mounting, installation and commissioning

in systems thanks to the alignment aids, plus

standardized connectivity and accessories

• Save installation time and certication costs

thanks to the unique, UL-certied and pre-

congured complete solution, equipped with

cable and pre-assembled in explosion-proof

enclosure (2GD variants)

Future-proof investment

• Various automation options enable the pro-

vision of information via IO-Link and subse-

quent use of data for downstream processes

• Technology leader due to smart and innova-

tive on-site diagnostic options via NFC and

“SICK Safety Assistant” mobile app

For the deTec4 Ex II 3GD, see page 10

Aim for high productivity

• Less downtime and increased machine

availability due to exceptional ruggedness and

reliability of all product components as well as

extensive and innovative diagnostic options

• High availability due to xed blanking:

Detection of skids, suppression of obstruc-

tions such as cables

For the C4000 Fusion Ex, see page 80

• Ecient access protection due to high scan-

ning ranges with low component requirements

For the deTem4 Core Ex, see page 86

Guaranteeing safety

• Maximum reliability and a very high level of

safety for your employees thanks to certi-

cation according to international safety

standards and compliance with the ATEX

guidelines for use in explosion-hazardous

areas

• Maximum safety for access protection of

automated material transport due to reliable

human-material dierentiation without the

need for an additional muting sensor

For the C4000 Fusion Ex, see page 80

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

Application areas

THE ULTIMATE LEVEL OF EXPLOSION PROTECTION

Whether highly explosive steam is created when painting car bodies or due to our dust in the air

of bottling systems, there is a risk of explosion in many industrial production areas. The rugged and

reliable housing design of the Ex versions of the safety light curtains and multiple light beam safety

devices from SICK prevent sparks from reaching explosive atmospheres. The risk of a potential ignition

source is therefore averted.

POWER

E.g. in coal, gas, or fuel plants

AUTOMOTIVE AND PARTS SUPPLIERS

E.g. In paint shops

READY FOR EXPLOSIVE ATMOSPHERES | SICK8024285/2019-07-23

Subject to change without notice

Application areas

FOOD AND BEVERAGE

E.g. in our lling facilities and distilleries

WOOD

E.g. in wood processing machines

WASTE AND RECYCLING

E.g. in combustion and sewage treatment plants

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

Selection guide

Product Device

type

Safety-

para-

meters

Resolution Number of

beams, beam

separation

Ambient

operating

tempera-

ture

Enclosure

rating

Functions Diagnostics Scanning

range up

to (m)

Page

Safety light curtain

Multiple light beam safety device

Type (IEC 61496)

Performance level (ISO 13849)

14 mm

20 mm

30 mm

40 mm

2 beams, 500 mm beam separation

3 beams, 400 mm beam separation

4 beams, 300 mm beam separation

0 °C ... +55 °C

–20 °C ... +55 °C

IP 65

IP 66

IP 67

Protective operation

Restart interlock

External device monitoring (EDM)

Beam coding

Automated calibration of the protective eld width

Congurable scanning range

Dynamic protective eld width during operation

Bypass

Operating mode switchover

PSDI mode

Reduced resolution

Fixed blanking

Floating blanking

Dynamic blanking for object pattern recognition

Self-teach dynamic Blanking for goods detection

Self-teach dynamic Blanking for pallet detection

Cascading

Smart presence detection

Dierentiation between man and material (muting)

Safe SICK device communication via EFI/SDL

Application diagnostic output (ADO)

IO-Link

Near Field Communication (NFC)

ATEX II 3G/3D

deTec4 Ex II 3GD 4 e 30 - 10

deTec4 Core Ex II 3GD 4 e 15 - 22

deTec2 Core Ex II 3GD 2 c 15 - On request

C4000 Advanced ATEX II 3G/3D 4 e 21 - 28

C4000 Fusion ATEX II 3G/3D 4 e 21 - 36

C4000 Entry/Exit ATEX II 3G/3D 4 e 21 - 46

deTem4 Core Ex II 3GD 4 e 90 - 54

deTem2 Core Ex II 3GD 2 c 90 - 60

ATEX II 2G/2D,

NFPA 70/NEC 500, classes I, II, III, div. 1

deTec4 Ex

4 e 25.2 - 66

deTec4 Core Ex 4 e 10 - 70

C4000 Advanced Ex 4 e 16 - 74

C4000 Fusion Ex 4 e 17.6 - 80

deTem4 Core Ex 4 e 14.2 - 86

Combined with a UE402 switching amplier

Auswahlhilfe

READY FOR EXPLOSIVE ATMOSPHERES | SICK8024285/2019-07-23

Subject to change without notice

Selection guide

Product Device

type

Safety-

para-

meters

Resolution Number of

beams, beam

separation

Ambient

operating

tempera-

ture

Enclosure

rating

Functions Diagnostics Scanning

range up

to (m)

Page

Safety light curtain

Multiple light beam safety device

Type (IEC 61496)

Performance level (ISO 13849)

14 mm

20 mm

30 mm

40 mm

2 beams, 500 mm beam separation

3 beams, 400 mm beam separation

4 beams, 300 mm beam separation

0 °C ... +55 °C

–20 °C ... +55 °C

IP 65

IP 66

IP 67

Protective operation

Restart interlock

External device monitoring (EDM)

Beam coding

Automated calibration of the protective eld width

Congurable scanning range

Dynamic protective eld width during operation

Bypass

Operating mode switchover

PSDI mode

Reduced resolution

Fixed blanking

Floating blanking

Dynamic blanking for object pattern recognition

Self-teach dynamic Blanking for goods detection

Self-teach dynamic Blanking for pallet detection

Cascading

Smart presence detection

Dierentiation between man and material (muting)

Safe SICK device communication via EFI/SDL

Application diagnostic output (ADO)

IO-Link

Near Field Communication (NFC)

ATEX II 3G/3D

deTec4 Ex II 3GD 4 e 30 - 10

deTec4 Core Ex II 3GD 4 e 15 - 22

deTec2 Core Ex II 3GD 2 c 15 - On request

C4000 Advanced ATEX II 3G/3D 4 e 21 - 28

C4000 Fusion ATEX II 3G/3D 4 e 21 - 36

C4000 Entry/Exit ATEX II 3G/3D 4 e 21 - 46

deTem4 Core Ex II 3GD 4 e 90 - 54

deTem2 Core Ex II 3GD 2 c 90 - 60

ATEX II 2G/2D,

NFPA 70/NEC 500, classes I, II, III, div. 1

deTec4 Ex 4 e

25.2 - 66

deTec4 Core Ex 4 e 10 - 70

C4000 Advanced Ex 4 e 16 - 74

C4000 Fusion Ex 4 e 17.6 - 80

deTem4 Core Ex 4 e 14.2 - 86

Combined with a UE402 switching amplier

Auswahlhilfe

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

deTec4 Ex II 3GD SAFETY LIGHT CURTAINS

Product description

Featuring a rugged and reliable housing

design, the deTec4 Ex II 3GD safety

light curtain is specially designed and

approved for use under the strict safety

requirements found in hazardous loca-

tions. The added safety and productivity

it oers in explosive atmospheres make

it a popular choice time and again.

At a glance

• Ex II 3GD classication thanks to

modied deTec4 housing

• NFC diagnostics and mobile app

• Diagnostics and automation via

IOLink

• 2-signal muting

• Reduced resolution: 1 or 2 beams

• Dynamic protective eld width

• Conguration of all functions without

software

Your benets

• Maximum safety and automation in

explosive atmospheres thanks to

compliance with stringent regulations

and strict safety requirements

• Less downtime thanks to comprehen-

sive, innovative diagnostic options

• Dierentiation between personnel

and materials (muting) to maximize

productivity

• Flexibility and safety for dynamic

applications

• Easy commissioning and congura-

tion without the need for software,

plus a standardized housing design

and accessories concept to save time

and money

Ready for explosive atmospheres

SAFETY LIGHT CURTAINS

deTec

deTec4 Ex II 3GD

Subject to change without notice

READY FOR EXPLOSIVE ATMOSPHERES

Additional information

Detailed technical data . . . . . . . . . . 11

Ordering information . . . . . . . . . . . . 13

Dimensional drawing . . . . . . . . . . . . .16

Recommended accessories . . . . . . .17

- www.sick.com/deTec

For more information, simply enter the link or scan the QR code and get direct access to

technical data, CAD design models, operating instructions, software, application examples, and

much more.

READY FOR EXPLOSIVE ATMOSPHERES | SICK8024285/2019-07-23

Subject to change without notice

SAFETY LIGHT CURTAINS deTec4 Ex II 3GD

Detailed technical data

Features

Resolution 14 mm Resolution 30 mm

Application

Explosive areas

Ex-approvals

ATEX for gas: II 3G Ex ec op is IIC T4 Gc

ATEX for dust: II 3D Ex tc IIIC T135°C Dc

Protective eld height

300 mm ... 2,100 mm (depending on type)

Scanning range

20 m 30 m

No blind zones

Yes

Synchronization

Optical synchronisation

Integrated laser alignment aid

Safety-related parameters

Type

Type 4 (IEC 61496-1)

Safety integrity level

SIL3 (IEC 61508)

SILCL3 (IEC 62061)

Category

Category 4 (ISO 13849-1)

Performance level

PL e (ISO 13849-1)

PFH

(mean probability of a dangerous

failure per hour)

Single device 15.3 x 10

-9

Cascade with one guest 30.5 x 10

-9

Cascade with two guest devices 45.6 x 10

-9

(mission time)

20 years (ISO 13849-1)

Safe state in the event of a fault

At least one OSSD is in the OFF state.

Functions

Protective operation

Automatic calibration of the protective

eld width

Beam coding

Restart interlock

External device monitoring (EDM)

Cascading

Smart presence detection

Reduced resolution

Dynamic protective eld width during

operation

Sender with reduced scanning range

Dierentiation between man and material

(muting)

Interfaces

Connection type

System plug

System connection

Depending on system plug (male connector M12, 5-pin or 8-pin)

Extension connection

Depending on system plug (without extension connection or with female connector M12, 5-pin)

Conguration method

DIP switch on system plug

Display elements

LEDs

For additional information on Flexi Soft g www.sick.com/Flexi_Soft

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

deTec4 Ex II 3GD SAFETY LIGHT CURTAINS

Display of the synchronization status of

the upper and lower beams

Application diagnostic output (ADO)

IO-Link

Near Field Communication (NFC)

Fieldbus, industrial network

Integration via Flexi Soft safety controller CANopen, DeviceNet™, EtherCAT

, EtherNet/IP™, Modbus TCP, PROFIBUS DP, PROFINET

For additional information on Flexi Soft g www.sick.com/Flexi_Soft

Electrical data

Protection class

III (IEC 61140)

Supply voltage V

24 V DC (19.2 V ... 28.8 V)

Ripple

≤ 10 %

Output signal switching devices (OSSDs)

Type of output 2 PNP semiconductors, short-circuit protected, cross-circuit monitored

ON state, switching voltage HIGH 24 V DC (V

– 2.25 V DC ... V

)

OFF state, switching voltage LOW ≤ 2 V DC

Current-carrying capacity per OSSD ≤ 500 mA

Application diagnostic output (ADO)

Type of output PNP semiconductor, short-circuit protected

Output voltage HIGH (active) ≥ V

– 3 V

Output voltage LOW (deactivated) High resistance

Output current HIGH (active) ≤ 100 mA

Applies to the voltage range between –30 V and +30 V.

Mechanical data

Dimensions

See dimensional drawing

Housing material

Aluminum extruded prole

Ambient data

Enclosure rating

IP65 (IEC 60529)

Ambient operating temperature

0 °C ... +55 °C

Storage temperature

–30 °C ... +70 °C

Air humidity

15 % ... 95 %, Non-condensing

Vibration resistance

5 g, 10 Hz ... 55 Hz (IEC 60068-2-6)

Shock resistance

10 g, 16 ms (IEC 60068-2-27)

Other information

Wave length

850 nm

Type of light

Near-infrared (NIR), invisible

Integrated laser alignment aid

Laser class 1

Wave length 650 nm

Type of light Visible red light

READY FOR EXPLOSIVE ATMOSPHERES | SICK8024285/2019-07-23

Subject to change without notice

SAFETY LIGHT CURTAINS deTec4 Ex II 3GD

Ordering information

deTec4 Ex II 3GD

A deTec4 Ex II 3GD safety light curtain consists of:

• Sender

• Receiver

• System plug sender (always SP1)

• System plug receiver (SP1 or SP2) - The receiver system plug denes the available functions of the deTec4 HG.

Selection aid deTec4 Ex II 3GD system plugs

System plugs for stand-alone:

• Sender: SP1

• Receiver: SP1 or SP2 (denes the available functions)

Options:

• System connection 5-pin or 8-pin (e.g. for RES, EDM, ADO, Muting)

• Receiver without or with extension connection (e.g. for RES, EDM, ADO, IO-Link, muting)

System plugs for host/guest cascade:

• Host sender: SP1 with extension connection

• Host receiver: SP1 or SP2 (denes the available functions) with extension connection

• Guest sender: SP1 with system connection M12, 5-pin

• Guest receiver: SP1 with system connection M12, 5-pin

Options:

• Host system connection 5-pin or 8-pin (e.g. for RES, EDM, ADO)

• Guest receiver without or with extension connection (e.g. for RES, EDM, ADO, IO-Link)

System plugs for host/guest/guest cascade:

• Host sender: SP1 with extension connection

• Host receiver: SP1 or SP2 (denes the available functions) with extension connection

• Guest1 sender: SP1 with system connection M12, 5-pin with extension connection

• Guest1 receiver: SP1 with system connection M12, 5-pin with extension connection

• Guest2 sender: SP1 with system connection M12, 5-pin

• Guest2 receiver: SP1 with system connection M12, 5-pin

Options:

• Host system connection 5-pin or 8-pin (e.g. for RES, EDM, ADO)

• Guest2 receiver without or with extension connection (e.g. for RES, EDM, ADO, IO-Link)

deTec4 Ex II 3GD: system plugs

Functions Usage System

connection

Extension connection Type Part no.

SP1

Sender

and receiver

Male connector

M12, 5-pin

– 1000 2076832

Female connector M12, 5-pin

(RES, EDM, ADO, IO-Link, cascading)

1100 2076833

Male connector

M12, 8-pin

(RES, EDM, ADO)

– 1200 2076834

Female connector M12, 5-pin

(RES, EDM, ADO, IO-Link, cascading)

1300 2076835

SP2 Receiver

Male connector

M12, 5-pin

– 2000 2093097

Female connector M12, 5-pin

(RES, EDM, ADO, IO-Link, cascading,

smart presence detection, muting)

2100 2093098

Male connector

M12, 8-pin

(RES, EDM, ADO,

muting)

– 2200 2093099

Female connector M12, 5-pin

(RES, EDM, ADO, IO-Link, cascading,

smart presence detection, muting)

2300 2093100

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

deTec4 Ex II 3GD SAFETY LIGHT CURTAINS

deTec4 Ex II 3GD: Sender with regular scanning range, receiver without LED indicator lamp

• Scope of delivery of sender and receiver without system plug. The system plugs must be ordered separately.

• For products with “On request” please contact your SICK representative.

Resolution Scanning range Protective eld

height

Sender Receiver

Type Part no. Type Part no.

14 mm 20 m

300 mm C4P-SX03011A00 1222438 C4P-EX03011C00 1222449

450 mm C4P-SX04511A00 On request C4P-EX04511C00 On request

600 mm C4P-SX06011A00 1222439 C4P-EX06011C00 1222450

750 mm C4P-SX07511A00 On request C4P-EX07511C00 On request

900 mm C4P-SX09011A00 On request C4P-EX09011C00 On request

1,050 mm C4P-SX10511A00 On request C4P-EX10511C00 On request

1,200 mm C4P-SX12011A00 On request C4P-EX12011C00 On request

1,350 mm C4P-SX13511A00 On request C4P-EX13511C00 On request

1,500 mm C4P-SX15011A00 On request C4P-EX15011C00 On request

1,650 mm C4P-SX16511A00 On request C4P-EX16511C00 On request

1,800 mm C4P-SX18011A00 1222440 C4P-EX18011C00 1222451

1,950 mm C4P-SX19511A00 On request C4P-EX19511C00 On request

2,100 mm C4P-SX21011A00 On request C4P-EX21011C00 On request

30 mm 30 m

300 mm C4P-SX03031A00 1222436 C4P-EX03031C00 1222447

450 mm C4P-SX04531A00 On request C4P-EX04531C00 On request

600 mm C4P-SX06031A00 On request C4P-EX06031C00 On request

750 mm C4P-SX07531A00 On request C4P-EX07531C00 On request

900 mm C4P-SX09031A00 On request C4P-EX09031C00 On request

1,050 mm C4P-SX10531A00 On request C4P-EX10531C00 On request

1,200 mm C4P-SX12031A00 On request C4P-EX12031C00 On request

1,350 mm C4P-SX13531A00 On request C4P-EX13531C00 On request

1,500 mm C4P-SX15031A00 1222437 C4P-EX15031C00 1222448

1,650 mm C4P-SX16531A00 On request C4P-EX16531C00 On request

1,800 mm C4P-SX18031A00 On request C4P-EX18031C00 On request

1,950 mm C4P-SX19531A00 On request C4P-EX19531C00 On request

2,100 mm C4P-SX21031A00 On request C4P-EX21031C00 On request

READY FOR EXPLOSIVE ATMOSPHERES | SICK8024285/2019-07-23

Subject to change without notice

SAFETY LIGHT CURTAINS deTec4 Ex II 3GD

deTec4 Ex II 3GD: Sender with reduced scanning range, receiver without LED indicator lamp

• Scope of delivery of sender and receiver without system plug. The system plugs must be ordered separately.

• For products with “On request” please contact your SICK representative.

• Sender with reduced scanning range: m

Resolution Scanning range Protective eld

height

Sender Receiver

Type Part no. Type Part no.

14 mm 2.5 m

300 mm C4P-SX03011C00 On request C4P-EX03011C00 1222449

450 mm C4P-SX04511C00 On request C4P-EX04511C00 On request

600 mm C4P-SX06011C00 On request C4P-EX06011C00 1222450

750 mm C4P-SX07511C00 On request C4P-EX07511C00 On request

900 mm C4P-SX09011C00 On request C4P-EX09011C00 On request

1,050 mm C4P-SX10511C00 On request C4P-EX10511C00 On request

1,200 mm C4P-SX12011C00 On request C4P-EX12011C00 On request

1,350 mm C4P-SX13511C00 On request C4P-EX13511C00 On request

1,500 mm C4P-SX15011C00 On request C4P-EX15011C00 On request

1,650 mm C4P-SX16511C00 On request C4P-EX16511C00 On request

1,800 mm C4P-SX18011C00 On request C4P-EX18011C00 1222451

1,950 mm C4P-SX19511C00 On request C4P-EX19511C00 On request

2,100 mm C4P-SX21011C00 On request C4P-EX21011C00 On request

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

deTec4 Ex II 3GD SAFETY LIGHT CURTAINS

Dimensional drawing (Dimensions in mm)

38,7

56,8

29,5

110,1

45,6

12,8

13,8

21,8

56,8

20,8

Protective eld height L1

300 313

450 463

600 613

750 763

900 913

1.050 1.063

1.200 1.213

1.350 1362

1.500 1.512

1.650 1.662

1.800 1.812

1.950 1.962

2.100 2.112

READY FOR EXPLOSIVE ATMOSPHERES | SICK8024285/2019-07-23

Subject to change without notice

SAFETY LIGHT CURTAINS deTec4 Ex II 3GD

Recommended accessories

Mounting systems

Terminal and alignment brackets

Alignment brackets

Figure Description Packing unit Type Part no.

FlexFix bracket for 1 device (e.g. sender or receiver), can be

aligned ± 15°, including M5 screw, plastic

2 pieces BEF-1SHABPKU2 2098709

FlexFix bracket for 2 devices (e.g. sender and receiver), can be

aligned ± 15°, including M5 screw, plastic

4 pieces BEF-1SHABPKU4 2066614

FlexFix mounting kit for 1 device, e.g. sender or receiver

(FlexFix bracket, alignment tool and assembly materials for

installation in PU3H device columns), plastic

2 pieces BEF-1SHABBKU2 2073543

FlexFix replacement bracket (mounting kit for replacement of

swivel mount brackets 2019649 and 2019659 or side bracket

2019506 with the FlexFix bracket when using the wells provid-

ed), Aluminum (anodised), plastic

4 pieces BEF-1SHABS004 2100345

FlexFix replacement bracket (mounting kit for replacement of

swivel mount brackets 2030510 or side bracket 2019506 with

the FlexFix bracket when using the wells provided), Aluminum

(anodised), plastic

4 pieces BEF-1SHABU004 2099282

QuickFix bracket for 1 device (e.g. sender or receiver), plastic 2 pieces BEF-3SHABPKU2 2066048

QuickFix bracket for 2 devices (e.g. sender and receiver),

plastic

4 pieces BEF-3SHABPKU4 2098710

Device protection (mechanical)

Front screen protection

Figure Description Suitable for Packing unit Type Part no.

Self-adhesive protective

lm for the front screen

(protects sensors from

damage by ying sparks

and welding beads)

Sucient for two sensors

with a protective eld

height of 2.100 mm

1 piece

Self-adhesive protective

lm

2069268

Other mounting accessories

Mounting tools

Figure Description Packing unit Type Part no.

Alignment tool for aligning sensors in areas with limited acces-

sibility, e.g. device columns

1 piece Alignment tool 4084133

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

deTec4 Ex II 3GD SAFETY LIGHT CURTAINS

Connection systems

Plug connectors and cables

Connecting cables

• Model: PUR, halogen-free, unshielded

Figure Connection type Conductor

cross-section

Length of cable Type Part no.

Female connector,

M12, 5-pin, angled

Flying leads 0.34 mm²

2 m YG2A15-020UB5XLEAX 2095772

5 m YG2A15-050UB5XLEAX 2095773

10 m YG2A15-100UB5XLEAX 2095774

Female connector,

M12, 5-pin, straight

Flying leads 0.34 mm²

2 m YF2A15-020UB5XLEAX 2095617

5 m YF2A15-050UB5XLEAX 2095618

10 m YF2A15-100UB5XLEAX 2095619

15 m YF2A15-150UB5XLEAX 2095620

20 m YF2A15-200UB5XLEAX 2095614

30 m YF2A15-300UB5XLEAX 2095621

Female connector,

M12, 8-pin, angled

Flying leads 0.25 mm²

2 m YG2A18-020UA5XLEAX 2095779

5 m YG2A18-050UA5XLEAX 2095780

10 m YG2A18-100UA5XLEAX 2095781

Female connector,

M12, 8-pin, straight

Flying leads 0.25 mm²

2.5 m YF2A18-025UA5XLEAX 2099229

5 m YF2A18-050UA5XLEAX 2095653

7.5 m YF2A18-075UA5XLEAX 2099230

10 m YF2A18-100UA5XLEAX 2095654

15 m YF2A18-150UA5XLEAX 2095679

20 m YF2A18-200UA5XLEAX 2095680

30 m YF2A18-300UA5XLEAX 2095681

Connection cables

• Model: PUR, halogen-free, unshielded

Figure Connection type Conductor

cross-section

Length of cable Type Part no.

Female connector,

M12, 4-pin, straight

Male connector,

M12, 4-pin, straight

0.34 mm² 0.2 m YF2A14-C20UB3M2A14 2096013

Female connector,

M12, 5-pin, straight

Male connector,

M12, 5-pin, straight

0.34 mm²

0.6 m YF2A15-C60UB5M2A15 2096006

1 m YF2A15-010UB5M2A15 2096007

2 m YF2A15-020UB5M2A15 2096009

5 m YF2A15-050UB5M2A15 2096010

10 m YF2A15-100UB5M2A15 2096011

15 m YF2A15-150UB5M2A15 2096171

Female connector,

M12, 8-pin, straight

Male connector,

M12, 8-pin, straight

0.25 mm²

0.6 m YF2A18-C60UA5M2A18 2096031

1 m YF2A18-010UA5M2A18 2096032

2 m YF2A18-020UA5M2A18 2096033

5 m YF2A18-050UA5M2A18 2096034

10 m YF2A18-100UA5M2A18 2096035

READY FOR EXPLOSIVE ATMOSPHERES | SICK8024285/2019-07-23

Subject to change without notice

SAFETY LIGHT CURTAINS deTec4 Ex II 3GD

Adapters and distributors

T-junctions

Figure Description Type Part no.

T-piece for simultaneous connection to sender and receiver, splits the cable from the

control cabinet to the sender and receiver, 5-pin

DSC-1205T000025KM0 6030664

T-distributor for simultaneous connection to sender and receiver, splits the cable

from the control cabinet between the sender and receiver, 8-pin

DSC-1208T000025KM0 6058647

Other adapters and distributors

Figure Description Type Part no.

IO-Link connector IO-Link connector 2092757

Muting connector Muting connector 2092758

Modules and gateways

Fieldbus modules

Figure Description Type Part no.

Illustration may

dier

EtherCAT IO-Link Master, IO-Link V1.1, Port Class A, power supply via 7/8’’ cable 24 V

/ 8 A, eldbus connection via M12 cable

IOLG2EC-03208R01 (IO-

Link Master)

6053254

Illustration may

dier

EtherNet/IP IO-Link Master, IO-Link V1.1, Port Class A, power supply via 7/8’’ cable

24 V / 8 A, eldbus connection via M12-cable

IOLG2EI-03208R01 (IO-

Link Master)

6053255

READY FOR EXPLOSIVE ATMOSPHERES | SICK 8024285/2019-07-23

Subject to change without notice

deTec4 Ex II 3GD SAFETY LIGHT CURTAINS

Figure Description Type Part no.

PROFINET IO-Link Master, IO-Link V1.1, Port Class A, power supply via 7/8’’ cable

24 V / 8 A, eldbus connection via M12 cable

IOLG2PN-03208R01 (IO-

Link Master)

6053253

Reectors and optics

Alignment aids

Figure Description Type Part no.

Laser alignment aid for various sensors, laser class 2 (IEC 60825). Do not look into

the beam!

AR60 1015741

Adapter AR60 for deTec4, deTec2 and MLG-2

AR60 adapter, deTec,

deTem, MLG-2

4070854

Further accessories

Test and monitoring tools

Figure Description Type Part no.

14 mm diameter Test rod 14 mm 2022599

24 mm diameter Test rod 24 mm 2045592

30 mm diameter Test rod 30 mm 2022602

34 mm diameter Test rod 34 mm 2045593

Programming and conguration tools

Figure Description Type Part no.

The 5-pin M12 button makes it possible to switch on and o the laser alignment aid

integrated into the deTec4 Prime sender.

Pushbutton for laser

alignment aid, M12, 5-pin

2082166

The 8-pin M12 button makes it possible to switch on and o the laser alignment aid

integrated into the deTec4 Prime sender.

Pushbutton for laser

alignment aid, M12, 8-pin

2082167

The pushbutton in combination with T-connector M12, 5-pin makes it possible to

switch on and o the laser alignment aid integrated into the deTec4 Prime sender

and works as a T-distributor for simultaneous connection to sender and receiver,

splits the cable from the control cabinet between the sender and receiver.

T-connector with pushbut-

ton for laser alignment

aid, M12, 5-pin

2077933

Page is loading ...

SICK Ready for explosive atmospheres Product information

SICK Ready for explosive atmospheres Product information

SICK Ready for explosive atmospheres Product information

Related papers

Other documents