ALIBI ALI-CD700 Quick Installation Manual

ALIBI
Brand
ALIBI
Model
ALI-CD700
Category
Security cameras
Type
Quick Installation Manual

This manual is also suitable for

1
www.observint.com
ALI-CD700_CQ
7/8/14
Power
Connector
Video BNC
Connector
Camera drop cable connectors (all ALI-CD700 series cameras)
What’s in the box
• Camera assembly
• Security L- wrench
• Mounting screws and wall inserts
• This manual
• Drill template
ALI-CD700 (left) and ALI-CD700VF (right) drill templates
Tools you need
To install the camera, you will need:
• 12 Vdc power source. See Specications for voltage and wattage requirements.
• Tools and additional fasteners (may be required) for mounting the camera
• Video and power extension cable
• CCTV video setup monitor (optional)
Installation
Before installation:
• Make sure that the device is in good condition and all the assembly parts are included.
• Check the specication of the products for the installation environment.
• Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
• To avoid re or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the Specications section.
During installation:
• Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning section.
• Monitor impedance: Set the monitor impedance switch to 75 .
• Power supply: Camera drop cable: The camera drop cable includes two connectors:
— Video BNC connector: For transmission of the video signal across a coax (75 ) extension
cable.
— Power connector: When applying Vdc power, observe the power polarity. See the picture
above for connector polarity conguration.
1. Using the drill template provided with your camera, mark the location of the screws that anchor the
base plate to the mounting surface. If you are routing the drop cable through base, also mark the
position of the hole for the drop cable.
2. Drill holes for the screws that anchor the base to the ceiling. The mounting hardware provided is
appropriate for most surfaces. However, depending on the surface materials, more appropriate
fasteners may be required.
ALI-CD700 Series Infrared Turret
Cameras Quick Installation Guide
ForProducts: ALI-CD700, ALI-CD700G (gray), ALI-CD700VF, ALI-CD700VFG (gray)
The ALIBI ALI-CD700 series turret cameras include a new generation sensor with high sensitivity and
advanced circuit design technology. They feature high resolution, low image distortion and low noise
features which makes them suitable for surveillance and image processing systems.
Features
• High resolution color sensor: 700 TV Lines
• IR LED enables the day/night surveillance
• 2.8 ~ 12 mm Varifocal lens (ALI-CD700VF series only)
• IR cut lter auto switch
• True day/night
• ATW brings high color rendition
• Auto electronic shutter control adapts to dierent surveillance environments
• Auto gain control, adaptive brightness
• High SNR for high-quality image
• 12 Vdc power
• Weather protection: IP66 rated
Mounting
plate
IR array
Lens
Camera
module
Enclosure
Clip plate
ALI-CD700 camera assembly
Mounting
plate
Clip plate
Base
assembly
IR array
Lens
Focus
adjust
Zoom
adjust
Camera
module
Enclosure
ALI-CD700VF camera assembly
2 www.observint.com
3. Drill a 3/4” hole for the drop cable, if necessary. The drop cable can be routed through the mounting
surface, or through a cable channel in the mounting plate.
4. Route camera video and power extension cables between camera location and the monitoring
device (monitor, DVR, etc.).
5. Remove the mounting plate from the camera assembly
u
Loosen the clip plate captive screw with the security L-wrench provided.
u
v
Clip plate
Enclosure
v Slide the clip plate out as shown in the photo above.
Separate the mounting base from the enclosure.
6. Anchor the mounting base to the ceiling with appropriate fasteners. If the camera drop cable will be
routed through a cable channel, make sure it is in place before securing the mounting plate to the
surface.
Cable channel (2)
7. Connect the camera drop cable to video and power extension cables.
8. Reattach the camera to the mounting plate.
u
Position the camera assembly onto the mounting plate such that the lip on the black ring
attached to the enclosure slips under the tabs on the mounting plate.
Mounting plate
u Tabs
Cable channel
v Slide the clip plate out.
v
y
x
Clip Plate
Mounting plate
Enclosure
 Push the enclosure into the mounting plate until it is fully seated.
x Slide the clip plate in so that it catches the lip of the black ring on the encloser.
y Tighten the clip plate screw until it is just snug.
9. Connect the far end of the video extension cable to a monitoring device, such as a surveillance
monitor or digital video recorder (DVR).
10. Connect the far end of the power extension cable to a power supply, then apply power to the
camera through the power extension cable.
11. While observing video from the camera on a monitor, aim the camera at your surveillance target.
See the gure below for adjustment ranges.
0 ~ 360
0 ~ 75
0 ~ 90
ALI-CD700VF series aiming the camera
For ALI-CD700VF series cameras only
12. Use a screwdriver to adjust the ZOOM screw and the FOCUS screw until you produce the best image.
Specications
Model ALI-CD700, ALI-CD700G ALI-CD700VF, ALI-CD700VFG
Image Sensor: 1/3” DIS 1/3” DIS
Signal System: NTSC NTSC
Eective Pixels: 976(H) × 496(V) 976(H) × 496(V)
Min. Illumination: 0.1 lux @ (F1.2, AGC ON),
0 lux with IR
0.1 lux @ (F1.2, AGC ON), 0 lux with IR
0.14 lux @ (F1.4, AGC ON),0 lux with IR
Shutter Time: 1/30 sec to 1/15,000 sec 1/60 sec to 1/100,000 sec
Lens: 3.6 mm
Angle of view: 68.4°
2.8 ~ 12 mm @ F1.4
Angle of view: 80° ~ 27.2°
Lens Mount: M12 φ14
Adjustment Range: Pan: 0 - 360°, Tilt: 0 - 75°,
Rotation: 0 - 360°
Pan: 0 - 360°, Tilt: 0 - 90°,
Rotation: 0 - 360°
Day & Night: IR cut lter with auto switch IR cut lter with auto switch
Horizontal Resolution: 700 TVL 700 TVL
Synchronization: Internal synchronization Internal synchronization
Video Output: 1 Vp-p composite output (75  / BNC) 1 Vp-p composite output (75  / BNC)
S/N Ratio: More than 62 dB More than 62 dB
BLC: ON On
Operating Conditions: -40 °F - 140 °F (-40 °C - 60 °C)
Humidity 90% or less (non-condensing)
-40 °F - 140 °F (-40 °C - 60 °C)
Humidity 90% or less (non-condensing)
Power Supply: 12 Vdc ± 10% 12 Vdc ± 10%
Power Consumption: Max. 1.8 W (max. 4 W with IR cut lter on) Max. 4 W (max. 5 W with IR cut lter on)
Weather Proof: IP66 IP66
IR Range: 32 ~ 65 ft (10 ~ 20 m) approx. 98 ~ 131 ft (30 ~ 40 m) approx.
Dimension: 3.53" × 2.33"
(89.6 × 59.1 mm)
5.28" × 4.88" × 3.47"
(134.2 × 123.9 × 88.1 mm)
Weight: 0.88 lbs (400 g) 1.76l lbs (800 g)
© 2014 Observint Technologies. All rights reserved.
3
www.observint.com
© 2014 Observint Technologies. All rights reserved.
Cleaning
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.
CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
carefully follow the accompanying instructions.
Troubleshooting
Problem Possible Cause
Nothing appears on the screen - Check the power connection.
- Check the video signal cable connection to the monitor.
The video image is dim or not clear. - If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark. - Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75  /Hi-Z)
properly, and check the cable connections.
The camera is not working properly and the
surface of the camera is hot.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
The image on the monitor ickers - Make sure that the camera isn’t facing direct sunlight or uorescent light.
If necessary,change the camera position.
  • Page 1 1
  • Page 2 2
  • Page 3 3

ALIBI ALI-CD700 Quick Installation Manual

ALIBI
Brand
ALIBI
Model
ALI-CD700
Category
Security cameras
Type
Quick Installation Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents