T-20 rental display
Safety manual
R59770258/00
09/05/2008
Barco NV Media and Entertainment Division
11101 Trade Center Drive, Rancho Cordova, California 95670, USA
Phone: +1 916 859-2500
Fax: +1 916 859-2515
E-mail: [email protected]
Visit us at the web: www.barco.com
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.883.86
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium
1. Safety
1. SAFETY
About this chapter
Read this chapter attentively. It contains important informa tion to prevent per sonal injury w hile installing the T-20 rental display.
Furthermore, it includes several cautions to prevent damage to the T-20 rental tile. Ensure that you understand and follow all safety
guidelines, safety instructions and warnings mentioned in this c hapter before installing the T-20 rental display.
Overview
• Safety g uidelines
• Important safety instructions
• Important warnings
• Proper usage
• Important warnings co ncerning T-20 flight cases and dollies
1.1 Safety g uidelines
Personal protection
WARNING: Ensure yo u understand an d follow all the safety guidelines, safety in structions, w arnings and
cautions mentioned in this m anual.
WARNING: Be aware of suspended loads.
WARNING: Wear a h ard hat to reduce the risk of personal injury.
WARNING: Be careful while w orking w ith heavy loads.
WARNING: Mind your fing ers w hile working with heavy loads.
Installation personnel
This installation must be performed by authorized a
nd qualified technical personnel only.
Accredited s afety officers m ust ensure the safety of the site, cons truction, assembly, connection, use, disman tling, transport etc. of
such saf ety critical system s.
Caution
Installationshould be performedonly after y ou arethoroughly familiar with allof the p rop er safety checks and installationinstructions.
To do otherwise increases the risk of hazards and injury to the us er.
Assembly parts are designed for intended use only in conjunction with T-20 LE D displays.
Do not m odify and/or replicate any component. Barco uses specific materials and m anufacturing processes in order to achieve part
strength. Consult Barco for assistance with c ustom applications.
Always follow Barco installation instructions. Contact Barco if you should have any question regarding the safety of an application.
The manufacturer assumes no liability for incorrect, inadequate, irresponsible or unsafe assembly of systems.
R59770258 T-20 RENTAL DISPLAY 09/05/2008
1
1. Safety
Product care
Structural & mounting components should be kep t dry, clean, lubricated (only if recommended), coated properly, and otherwise
maintained in a manner consistent with part design. Barco products must be used in a manner consistent with their design and
inspected on a routine ba sis for security, wear,deformation, corrosion and any other circumstances that may affect the load handling
capability of the part.
Barco recommends inspections at regular inte rvals for a ll installations and increasing in frequency for more c ritical installations. If
a part is found to hav e damage, w hich m ay cause a de creas e in load capability, the part must be rem oved for service o r replaced
immediately.
Under no circumstances are Barco par ts repairable by any one other than Barco.
1.2 Important safety instructions
Instructions:
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with materials or chem icals that are inert, nonabrasive, n oncorrosive and non-marking. C onsult the manufacturer
for further advice should any doubts exist regarding any cleaning procedu
re.
• Do not block ventilation openings. Install in accordance with the manufacturers instructions.
• Do not install near any heat sources s uch as radiators, heat re gisters, s toves, or other apparatus (including amplifiers) that
produce heat.
• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided sockets/plugs are damaged
then replacement of the defective parts must be undertaken immediately.
• Protect the power/data cords from being walked on or pinched particularly at p
lugs, convenience recep tacles, an d the point
where they exit from the apparatus. Replac e damaged power/data cords immediately.
• Only use attachments/accessories specified by the manufacturer.
• Disconnect the pow er to this apparatus during lightning storms or provide suitable additional lightning protection. Unplug this
apparatus when unused for long period of time.
• Refer all servicing to qualified service technicians/personnel. Servicing is required when the apparatus has been dam aged in
any way, such as power-supply cord or plug is damaged, the appa ratus does not operate normally, or has been dropped.
• Use only with s ystems orperipheralsspecified by themanufacturer, or s old with theapparatus. Use cautionduring lifting/moving
or transporting to avoid dam age by possible tipping.
1.3 Important warnings
Important warnings:
Risk of electric shock:
Do n ot open. To reduce the risk of electric shock, do not rem ove cover (or back). No user-serviceable parts inside. Refer servicing
to qua lified service personnel.
Maximum and minimum am bient tem perature:
The maximum ambient temperature for the LED wall is 50 °C, the m inimum t emperature is -35 °C.
High leakage current:
The com bination of multiple tiles in an installation results in increa sed levels of leakage current. In order to avoid risk of electric
shock due to high leakage current, proper groundi
ng of the installation is required.
Flammable materials:
Keep flammable materials away from the installation (such as curtains). A lot of energy is transferred into heat. The installation
should be such that the amount of air flow required for safe operation of the equipm ent is not compromised. Proper ventilation must
be provided.
Risk of electric sho ck / Risk of fire:
To protect against risk of fire caused by overloading of power cables, MAX IMUM six (6) tiles may b e connected in parallel. Each
power source cable s upplying maximum six (6) tiles should be protected by a circuit breaker or fuses rated 16 A / 250 VAC (15 A /
250 VAC in the USA and Canada). Note that one T-20
tile requires 200-240 VA C , 50-60 Hz, 1.56 amps at 230 VA C.
Mechanical stress:
2
R59770258 T-20 RENTAL DISPLAY 09/05/2008
1. Safety
Use the T-20 rental tiles in a hanging configur ation only. Maximum allowed T-20 display height is 10 tiles high. Never trus s more
than 10 tiles high.
Disconnect d evice:
When the appliance inlets of the individual tiles are not accessible, the socket outlets supplying the rack shall be installed ne ar the
equipment and b e easily ac cessible, or a readily accessible gen eral disconnect device shall be incorporated in the fixed wiring.
This equipm ent MUS T be earthed:
In order to protect againstrisk of electric shock, the installation should be p roperly grounded. Defeating the purpose of the grounding
type plug will expose you to the risk of electric shock.
Power system :
It is recommended to use a TN-S power distribution system (a power distribution system with a separate neutral and grounding
conductor) in order to avoid large groun d current loops du e to voltage differences in the n eutral c onductor. The total electrical
installation should be protectedbyanappropriatelyrateddisconnectswitch, circuitbreakers, over voltage protector and G round Fault
Current Interrupters. The installation shall be done according to the local electrical installation codes. In Europe special attention
should be g iven to EN 60364, the standard for electrical installation of buildings. In G erma ny VDE 0100 should be adhered to. In
America, special attention should be given to the National Electrical Code, ANS I/NFPA 70.
Mains cords:
The power cords de livered with this system ha ve special properties for safety. They ar e no t user serviceable. If the power cords are
damaged, replace them only with new ones. Never try to repair a power cord.
Data cables:
The data cables provided with this system have special properties for safety. They are not user serviceable. If the data cables are
damaged, replace them only with new ones . Never try to repair a data cable. Pe r requirements of the National Electrical Code®
in the USA , the length of a data cab le must not exceed 42 m (140 feet). Avoid exposure of data cables to accidental contact with
lightning or power conductors.
1.4 Proper usage
Proper usage of T-20 tiles
• No part of the T-20 tile can come in contact with any type of abrasive.
• No part of the T-20 tile can com e in c ontact with any type of corrosive substance.
• T-20 tiles are to be u sed in environments meeting the op erating specifications.
• T-20 tiles are not to be exposed to extreme localized heat or c old exceeding the temperature s pecifica tions.
• T-20 tiles are not to be exposed to any element or situation that will cause any pa rt of the display to heat beyond what occurs
during normal operation. Such situations include but are not limited to lasers, ultrasonic vibration, o r any type of substance that
prevents proper ventilation and heat radiation o f the T-20 tiles.
• Power connected to the T-20 tiles must meet the specifications outlined in the installation manual.
• Neverplace an T -20 tile upon asurfacewiththe LED’sfacingdownwards. This to pr event damage tothe LED’sand the shaders.
• T-20 tiles which are not installed and which are not securely stored in an T -20 flight case, m ay only be placed ver tically upon
flat surfaces free of clutter.
• No force can be applied to the LED’s. Any LED’s dam aged due to mechanical stress are not c overed by the warranty.
• Safety and functional features of the display cannot be defeated.
• It is not allowed to climb or hang any additional equipment on the back of an T-20 wall. Nothing is to be allowed to hang from
the cables of a n T-20 tile.
• Any failures must be imm ediately and appropriately dealt with (equipment returned to B arco?). Failing eq uipment cannot be
left t o r un in a wall.
• No additional tools (hammers, pry-bars, etc.) are to be used to force handles or locks into place . All moving parts should be
managed by hand. Only a 8 mm Allen wrench may be used.
• Only Barco cables s pecified to be used with the T-20 display are to be used to connect components in an T-20 wall. Further,
care must be taken to connect signal only accordi
ng to the installation manual.
• T-20 tiles are not to be used in the vicinity of any equipment that is not CE and UL/ETL certified.
• T-20 tiles are not to be transported for any distance in containers other than Barco T-20 flight cases or Barco T-20 dollies or
T-20 single unit pac kaging. Further, even the use of Barco flight cases, dollies or packaging material does not g uarantee the
T-20 tiles aga inst dam age due to excessive force of impacts.
• T-20 tiles are not to be connected to any non-Barco equipment.
• When hanging T -20 tiles, only B arco T-20 trusses ca
n be used and they m ust be installed and connected a ccording to the
manual. Improper hanging of T-20 tiles can result in excessive forces on the structural c omponents of theT-20 tiles.
• T-20 tiles are only to b e installed ve rtically. Any tilting of a display w ill cause undue stress on the structural components of the
T-20 tiles.
• T-20 tiles can be trussed u p to 10 tiles high. Never truss more than 10 tiles high.
• T-20 tiles can be cleaned only in accordance to the procedures de fined in the installation manual.
R59770258 T-20 RENTAL DISPLAY 09/05/2008
3
1. Safety
• The T-20 tile is equipped with two high density air filters. These filters must be replaced on a regular basis, depending on the
environment conditions of the tile. It is r ecom mended to replace the filters every 6 months.
1.5 Important warnings concerning T- 20 flight cases and dollies
Important warnings concerning T-20 flight cases and dollies
• Always us e a forklift to transport the T-20 dolly. The castor w heels of th e T-20 dolly may only be used to reposition the T-20
dolly locally on the events floor (E.g . to line up the T-20 dollies).
• Before using T-20 flight cases or dollies, check the wheels and their fixation screws for wear or defects.
• Before transporting T -20 flight cases or T-20 do llies, ch eck that the all lock handles are in good work ing or der an d locked
secure ly.
• Before transporting T-2 0 dollies, check t hat the T-20 t iles are securely locked into the base of the T-20 dollies and upon each
other.
• Never transport T-20 dollies unless they are completely empty o r fully loaded.
• Never transport T-20 dollies without all side panels an d top cover installed.
• Never stack T-20 dollies.
• Never transport more then twelve T-20 tiles upon one dolly.
• Use an appropriate forklift to raise T-20 flight cases or T-20 dollies and take the neces sary precautions to avoid personal injury.
• Surface on which T-20 flight case or T-20 dolly is standing must be level to ensure that the total load is evenly spread out among
the four wheels. The surface must also b e able to support the load safely.
• The T-20 rental flight case for the T-20 single and dualtruss beams can be stacked maximum two (2) high. N ever higher. When
stacked, mak e sure the wheels of the upper flight case are precisely positioned in the stacking dishes of the flight case below.
• Always rigidly strap the T-20 flight cases and T-20 dollies in a truck or other transport medium.
• Do not use the breaks of the T-20 flight cases and T-20 dollies in a truc k or other transport medium.
4
R59770258 T-20 RENTAL DISPLAY 09/05/2008
Page is loading ...
Barco NV Media and Entertainment Division
11101 Trade Center Drive, Rancho Cordova, California 95670, USA
Fon: +1 916 859-2500
Fax: +1 916 859-2515
E-mail: folsomsales@barco.com
Web: www.barco.com
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Fon: +32 56.36.89.70
Fax: +32 56.36.883.86
E-mail: [email protected]
Web: www.barco.com
Printed in Belgium
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Barco NV Media and Entertainment Division
11101 Trade Center Drive, Rancho Cordova, California 95670, USA
Teléfono: +1 916 859-2500
Fax: +1 916 859-2515
E-mail: folsomsales@barco.com
Visite nuestra web: www.barco.com
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Teléfono: +32 56.36.89.70
Fax: +32 56.36.883.86
E-mail: [email protected]
Visite nuestra web: www.barco.com
Impreso en Belgium
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Barco NV Media and Entertainment Division
11101 Trade Center Drive, Rancho Cordova, California 95670, USA
Tél.: +1 916 859-2500
Fax: +1 916 859-2515
E-mail: folsomsales@barco.com
Rendez nous visite sur le web: www.barco.com
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Tél.: +32 56.36.89.70
Fax: +32 56.36.883.86
E-mail: [email protected]
Rendez nous visite sur le web: www.barco.com
Imprimé en Belgium
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Barco NV Media and Entertainment Division
11101 Trade Center Drive, Rancho Cordova, California 95670, USA
Phone: +1 916 859-2500
Fax: +1 916 859-2515
E-mail: folsomsales@barco.com
Visitate il web: www.barco.com
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.883.86
E-mail: [email protected]
Visitate il web: www.barco.com
Stampato in Belgium
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Barco NV Media and Entertainment Division
11101 Trade Center Drive, Rancho Cordova, California 95670, USA
Tel: +1 916 859-2500
Fax: +1 916 859-2515
電子メール: [email protected]
Barco Webサイト: www.barco.com
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Tel: +32 56.36.89.70
Fax: +32 56.36.883.86
電子メール: s[email protected]
Barco Webサイト: www.barco.com
Printed in Belgium
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Barco NV Media and Entertainment Division
11101 Trade Center Drive, Rancho Cordova, California 95670, USA
Tel.: +1 916 859-2500
Fax: +1 916 859-2515
E-mail: folsomsales@barco.com
Bezoek ons op het web: www.barco.com
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Tel.: +32 56.36.89.70
Fax: +32 56.36.883.86
E-mail: [email protected]
Bezoek ons op het web: www.barco.com
Gedrukt in Belgium
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Barco NV Media and Entertainment Division
11101 Trade Center Drive, Rancho Cordova, California 95670, USA
Telefone: +1 916 859-2500
Fax: +1 916 859-2515
E-mail: folsomsales@barco.com
Visite-nos na internet: www.barco.com
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Telefone: +32 56.36.89.70
Fax: +32 56.36.883.86
E-mail: [email protected]
Visite-nos na internet: www.barco.com
Impresso em Belgium
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Barco NV Media and Entertainment Division
11101 Trade Center Drive, Rancho Cordova, California 95670, USA
电话: +1 916 859-2500
传真: +1 916 859-2515
电子邮件: folsomsales@barco.com
通过 Web 访问我们: www.barco.com
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
电话: +32 56.36.89.70
传真: +32 56.36.883.86
电子邮件: [email protected]
通过 Web 访问我们: www.barco.com
印刷于 Belgium
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
