Caroma CL10020.B: The Ultimate Square Wall Mixer Trim Kit for Your Bathroom
Elevate your bathroom experience with the Caroma CL10020.B, a premium square wall mixer trim kit designed for both style and functionality. This high-quality kit boasts a sleek, modern design that effortlessly complements any contemporary bathroom décor. With its durable construction and easy installation process, the Caroma CL10020.B is the perfect choice for homeowners seeking a reliable and stylish bathroom solution.
Features:
- Stunning square design adds a touch of modern elegance to your bathroom
- Easy to install, ensuring a quick and hassle-free setup
Caroma CL10020.B: The Ultimate Square Wall Mixer Trim Kit for Your Bathroom
Elevate your bathroom experience with the Caroma CL10020.B, a premium square wall mixer trim kit designed for both style and functionality. This high-quality kit boasts a sleek, modern design that effortlessly complements any contemporary bathroom décor. With its durable construction and easy installation process, the Caroma CL10020.B is the perfect choice for homeowners seeking a reliable and stylish bathroom solution.
Features:
- Stunning square design adds a touch of modern elegance to your bathroom
- Easy to install, ensuring a quick and hassle-free setup
Suitable for item codes: CL10020.B
clark.com.au
BARCODE
In
c
l
uded
A
cc
es
s
o
r
ies
FOR EASY INSTALLATION PACK INCLUDES: DETAILED INSTALLATION INSTRUCTIONS,
CUT-OUT TEMPLATE, SEALING TAPE & MOUNTING CLIPS
clark.com.au
Vital
> Manufactured from
quality 304 grade
stainless steel for
enhanced hygiene.
> Left or right bowl
options available.
> 1 tap hole.
> A stylish solution for
your kitchen with a
main bowl deep
enough for a variety of
uses, a handy second
bowl and a functional,
modern drainer.
> Lifetime Warranty.
Stainless Steel
Basket Wastes
> Push down to seal,
pull up to drain &
remove to empty.
Vital Left Hand Bowl
One Tap Hole
1125.1L
Right Hand Bowl
One Tap Hole
1125.1R BARCODE
Vital
CUT OUT TEMPLATE AND SINK INSTALLATION INSTRUCTIONS
This pack contains the following components to
assist in the installation of your product:
Fixing Clips
Sealing Tape
2 x 90mm Basket wastes
INSTALLATION INSTRUCTIONS
1. Finish cutting out this template with a knife
or scissors.
2. Position the template on the bench top and
draw a pencil line against the edge of the template.
Then check the size against the overall cutout
dimensions before cutting the bench top.
3. Following the inside edge of the pencil line
carefully cut out the hole in the bench top.
An exact cut is required to obtain best fit.
4. For a normal thickness benchtop the enclosed
fixing clips should be suitable. Lightly hammer the
fixing clips onto the clip brackets at equal points
along the product rim. See Figure A. If the thickness
of the bench top exceeds the range of the fixing
clips then extension clips can be purchased and
mounted onto the clip brackets. See Figure B.
5. Position the product in the cut out hole so that
it is properly aligned. Check that the sealing tape
will seal evenly around the edge of the hole.
6. Remove the product and install the waste
assemblies and the tap (if required). It is
suggested that silicone sealer be used
between the waste grate and hole.
7. Remove the protective backing from the
sealing tape, apply a continuous bead of
silicone sealer between the sealing tape
and the edge of the product. Quickly place
the product in position.
8. Close the fixing clip hinges as shown in
Figure C.
9. Tighten the fixing clips evenly, using a low
torque setting on any electric screw driver
used. Overtightening may strip the thread.
10. Plumb up the tap and waste fittings.
NOTE: For thin benchtops special clips (A0167) are available.
CUTOUT TEMPLATE DIMENSIONS
956 x 456mm
Corner Radius: 6mm
SINK
CLIP BRACKET
FIXING CLIP
FIGURE A
SINK
FIXING CLIP
CLIP BRACKET
EXTENSION CLIP
FIGURE B
BENCH TOP
FIGURE C
BENCH TOP
FIGURE D
Caroma Industries Limited
ABN 35 000 189 499
1 Melito Court,
Prestons, NSW 2170
National Customer Call Centre
09 279 2700
caroma.co.nz
New Zealand
Caroma Industries Limited
ABN 35 000 189 499
1 Melito Court, Prestons NSW 2170
National Customer Call Centre
13 14 16
caroma.com.au
Round Square Wall Mixer Trim
Kit (Square) - Chrome
CL10020./Rev. 0
PLUMBERS INSTALLATION
INSTRUCTIONS Hot and cold water inlet pressures should be equal.
Maximum hot water temperature : 80 C.
IMPORTANT
Pressure & Temperature Requirements.
New Regulation :-500 kPa maximum static pressure
at any outlet within a building. (Ref. AS/NZS 3500.1)
Static inlet pressure range : 150 -1000 kPa
Installation Requirements.
The installing plumber is responsible for waterproofing
all penetrations for Taps in Shower areas at installation
by a proprietary flange system or a sealant.(Ref AS3740)
PLUMBERS INSTALLATION INSTRUCTIONS
ROUND SQUARE - BATH/SHOWER MIXER
*
*
Installation (Fig. 1 & 2)
Body kit: Fit mixer body (9) onto a suitable mounting plate
or noggin in the wall and secure using screws through the
holes in its base. When facing the mixer, the connections
should be as follows :
Hot water inlet connection 'H' to the left.
Cold water inlet connection 'C' to the right.
Mixed water outlet connection, vertically upwards.
Check all connections for leaks and the tap for correct
operation.
Important :
Mixer body (9) must be installed square to wall/tile face, to
ensure cover plate (5) sits flush.
To avoid damaging the decorative finish, do not remove the
plastic protective sleeve until installation has been completed.
1)
Brazed connections should NOT be made directly onto
the mixer, as exccesive heat will cause permanent
damage.
All pipework must be thoroughly flushed prior to
installation.
*
*
Important Information
2) Trim kit: Apply a suitable clear sealant to the back face of the
cover plate (5), leaving an unsealed section at the bottom for
drainage. Carefully fit the cover plate (5) onto the mixer body (9).
Push the cover plate (5) firmly against the wall/tile face.
Wipe clean any excess sealant from the cover plate surfaces
and the wall/tile face (See Fig. 1).
Fit handle (1) taking care that it is pushed fully onto cartridge
stem, then tighten grub screw (2) using the 2.5mm allen key (3).
Fit plug (4), taking care not to damage the decorative finish.
Turn on Hot and Cold water supplies and check operation.
3)
4)
For warranty details refer to www.clark.com.au
*
Trim kit (1-5) & body kit (6-9) are sold separately.
*
Final install must be checked at rough-in stage (step 1).
*
Replacing Cartridge (Fig. 2)
1) Turn off hot and cold water supplies.
2)
3) Ensure inside face of mixer body (9) is clean. First
check that seal is in position in base of new cartridge
then fit new cartridge (8) into mixer body, taking care
that two lugs on base of cartridge fit into mating holes
in mixer body (9).
4) Screw on nut (7). Important : Nut (7) should be
tightened to a torque of 10Nm. Replace cap (6)
and tighten firmly by hand.
5)
Turn on water supplies and check operation.
6)
Carefully remove plug (4) before using a 2.5mm allen key (3)
to loosen grub screw (2) and remove handle (1).
Remove cap (6) taking care not to damage the decorative
finish. Unscrew nut (7), then lift out the old cartridge.
Fit handle (1) taking care that it is pushed fully onto cartridge
stem, then tighten grub screw (2) using the 2.5mm allen key (3).
Replace plug (4), taking care not to damage the decorative finish.
Hot and cold water inlet pressures should be equal.
Maximum hot water temperature : 80 C.
IMPORTANT
Pressure & Temperature Requirements.
New Regulation :-500 kPa maximum static pressure
at any outlet within a building. (Ref. AS/NZS 3500.1)
Static inlet pressure range : 150 -1000 kPa
Installation Requirements.
The installing plumber is responsible for waterproofing
all penetrations for Taps in Shower areas at installation
by a proprietary flange system or a sealant.(Ref AS3740)
PLUMBERS INSTALLATION INSTRUCTIONS
ROUND SQUARE - BATH/SHOWER MIXER
*
*
Installation (Fig. 1 & 2)
Body kit: Fit mixer body (9) onto a suitable mounting plate
or noggin in the wall and secure using screws through the
holes in its base. When facing the mixer, the connections
should be as follows :
Hot water inlet connection 'H' to the left.
Cold water inlet connection 'C' to the right.
Mixed water outlet connection, vertically upwards.
Check all connections for leaks and the tap for correct
operation.
Important :
Mixer body (9) must be installed square to wall/tile face, to
ensure cover plate (5) sits flush.
To avoid damaging the decorative finish, do not remove the
plastic protective sleeve until installation has been completed.
1)
Brazed connections should NOT be made directly onto
the mixer, as exccesive heat will cause permanent
damage.
All pipework must be thoroughly flushed prior to
installation.
*
*
Important Information
2) Trim kit: Apply a suitable clear sealant to the back face of the
cover plate (5), leaving an unsealed section at the bottom for
drainage. Carefully fit the cover plate (5) onto the mixer body (9).
Push the cover plate (5) firmly against the wall/tile face.
Wipe clean any excess sealant from the cover plate surfaces
and the wall/tile face (See Fig. 1).
Fit handle (1) taking care that it is pushed fully onto cartridge
stem, then tighten grub screw (2) using the 2.5mm allen key (3).
Fit plug (4), taking care not to damage the decorative finish.
Turn on Hot and Cold water supplies and check operation.
3)
4)
For warranty details refer to www.clark.com.au
*
Trim kit (1-5) & body kit (6-9) are sold separately.
*
Final install must be checked at rough-in stage (step 1).
*
Replacing Cartridge (Fig. 2)
1) Turn off hot and cold water supplies.
2)
3) Ensure inside face of mixer body (9) is clean. First
check that seal is in position in base of new cartridge
then fit new cartridge (8) into mixer body, taking care
that two lugs on base of cartridge fit into mating holes
in mixer body (9).
4) Screw on nut (7). Important : Nut (7) should be
tightened to a torque of 10Nm. Replace cap (6)
and tighten firmly by hand.
5)
Turn on water supplies and check operation.
6)
Carefully remove plug (4) before using a 2.5mm allen key (3)
to loosen grub screw (2) and remove handle (1).
Remove cap (6) taking care not to damage the decorative
finish. Unscrew nut (7), then lift out the old cartridge.
Fit handle (1) taking care that it is pushed fully onto cartridge
stem, then tighten grub screw (2) using the 2.5mm allen key (3).
Replace plug (4), taking care not to damage the decorative finish.
Hot and cold water inlet pressures should be equal.
Maximum hot water temperature : 80 C.
IMPORTANT
Pressure & Temperature Requirements.
New Regulation :-500 kPa maximum static pressure
at any outlet within a building. (Ref. AS/NZS 3500.1)
Static inlet pressure range : 150 -1000 kPa
Installation Requirements.
The installing plumber is responsible for waterproofing
all penetrations for Taps in Shower areas at installation
by a proprietary flange system or a sealant.(Ref AS3740)
PLUMBERS INSTALLATION INSTRUCTIONS
ROUND SQUARE - BATH/SHOWER MIXER
*
*
Installation (Fig. 1 & 2)
Body kit: Fit mixer body (9) onto a suitable mounting plate
or noggin in the wall and secure using screws through the
holes in its base. When facing the mixer, the connections
should be as follows :
Hot water inlet connection 'H' to the left.
Cold water inlet connection 'C' to the right.
Mixed water outlet connection, vertically upwards.
Check all connections for leaks and the tap for correct
operation.
Important :
Mixer body (9) must be installed square to wall/tile face, to
ensure cover plate (5) sits flush.
To avoid damaging the decorative finish, do not remove the
plastic protective sleeve until installation has been completed.
1)
Brazed connections should NOT be made directly onto
the mixer, as exccesive heat will cause permanent
damage.
All pipework must be thoroughly flushed prior to
installation.
*
*
Important Information
2) Trim kit: Apply a suitable clear sealant to the back face of the
cover plate (5), leaving an unsealed section at the bottom for
drainage. Carefully fit the cover plate (5) onto the mixer body (9).
Push the cover plate (5) firmly against the wall/tile face.
Wipe clean any excess sealant from the cover plate surfaces
and the wall/tile face (See Fig. 1).
Fit handle (1) taking care that it is pushed fully onto cartridge
stem, then tighten grub screw (2) using the 2.5mm allen key (3).
Fit plug (4), taking care not to damage the decorative finish.
Turn on Hot and Cold water supplies and check operation.
3)
4)
For warranty details refer to www.clark.com.au
*
Trim kit (1-5) & body kit (6-9) are sold separately.
*
Final install must be checked at rough-in stage (step 1).
*
Replacing Cartridge (Fig. 2)
1) Turn off hot and cold water supplies.
2)
3) Ensure inside face of mixer body (9) is clean. First
check that seal is in position in base of new cartridge
then fit new cartridge (8) into mixer body, taking care
that two lugs on base of cartridge fit into mating holes
in mixer body (9).
4) Screw on nut (7). Important : Nut (7) should be
tightened to a torque of 10Nm. Replace cap (6)
and tighten firmly by hand.
5)
Turn on water supplies and check operation.
6)
Carefully remove plug (4) before using a 2.5mm allen key (3)
to loosen grub screw (2) and remove handle (1).
Remove cap (6) taking care not to damage the decorative
finish. Unscrew nut (7), then lift out the old cartridge.
Fit handle (1) taking care that it is pushed fully onto cartridge
stem, then tighten grub screw (2) using the 2.5mm allen key (3).
Replace plug (4), taking care not to damage the decorative finish.
Hot and cold water inlet pressures should be equal.
Maximum hot water temperature : 80 C.
IMPORTANT
Pressure & Temperature Requirements.
New Regulation :-500 kPa maximum static pressure
at any outlet within a building. (Ref. AS/NZS 3500.1)
Static inlet pressure range : 150 -1000 kPa
Installation Requirements.
The installing plumber is responsible for waterproofing
all penetrations for Taps in Shower areas at installation
by a proprietary flange system or a sealant.(Ref AS3740)
Fig. 2
Apply Sealant
(See Installation Note 2)
9
5678
Seal
Lugs
1
2
3
4
50
outlet to bath
or shower
G1/2" BSP
INT.
G1/2" BSP
INT.
Fig. 1
50-60mm
wall/tile face
MAXIMUM
5
9
Wipe clean excess sealant
Fig. 2
Apply Sealant
(See Installation Note 2)
9
5678
Seal
Lugs
1
2
3
4
50
outlet to bath
or shower
G1/2" BSP
INT.
G1/2" BSP
INT.
Fig. 1
50-60mm
wall/tile face
MAXIMUM
5
9
Wipe clean excess sealant
-
1
Caroma CL10020.B: The Ultimate Square Wall Mixer Trim Kit for Your Bathroom
Elevate your bathroom experience with the Caroma CL10020.B, a premium square wall mixer trim kit designed for both style and functionality. This high-quality kit boasts a sleek, modern design that effortlessly complements any contemporary bathroom décor. With its durable construction and easy installation process, the Caroma CL10020.B is the perfect choice for homeowners seeking a reliable and stylish bathroom solution.
Features:
- Stunning square design adds a touch of modern elegance to your bathroom
- Easy to install, ensuring a quick and hassle-free setup
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
ALDER TAPWARE Vito Bertoni Series User manual
-
enware FWS031 Installation, Operating, & Maintenance Instructions
-
HP COMBI 2180206H User manual
-
enware LEVA Installation Instructions Manual
-
Mira Virtue Installation & User Manual
-
-
Mira Crescent Installation & User Guide
-
-
Mira Miniduo Installation & User Guide
-
Triton HUMBER Installation And Operating Instructions Manual
