Eaton EMR-5000 Installation, Operation and Maintenance Manual

EMR-5000 - EATON MOTOR RELAY

Installation, Operation and Maintenance

Software-Version: 2.5.b

IM02602012E

Revision: A

English

EMR-5000 IM02602012E

EMR-5000 Functional Overview

www.eaton.com 2

Trend recorder

Event recorder

Current and Volt.:

unbalance

%THD and THD

Fund. and RMS

min./max./avg.

phasors and

angles

Power:

Fund. and RMS

MVA, Mwatt, Mvar,

PF

Metering,

Statistics and

Demand

standard

3

1

3

EMR-5000

74

TC

*

Zone

Interlocking

Breaker Wear

Programmable

Logic

51

50R

46 50J 51P

27A

59A

47

55

A/D

27M 59M

81

U/O

51X

LOP

51V 50X

1

Fault recorder

Waveform recorder

Option

Motor

Load

URTD Assembly

14

Analog

Outputs and

Inputs

51R

37 49S

50P

50

BF

CTS

32

32V

81 R 78V

49

Start recorder

Statistics recorder

History function

66

IRIG-B00X

SNTP

87M

URTD Assembly

3

EMR-5000 IM02602012E

Table of Contents

EMR-5000 Functional Overview.............................................................................................................................. 2

Table of Contents.................................................................................................................................................... 3

Comments on the Manual........................................................................................................................................ 9

What Is Included with the Device................................................................................................................................. 14

Storage........................................................................................................................................................................ 14

Important Information ................................................................................................................................................. 14

Symbols....................................................................................................................................................................... 15

General Conventions................................................................................................................................................... 21

Load Reference Arrow System.................................................................................................................................... 22

Device................................................................................................................................................................... 23

Device Planning........................................................................................................................................................... 23

Installation and Wiring........................................................................................................................................... 27

Three-Side-View.......................................................................................................................................................... 27

Overview of Slots - Assembly Groups......................................................................................................................... 29

Slot X1: Power Supply Card with Digital Inputs...........................................................................................................31

Slot X2: Relay Output Card - Zone Interlock................................................................................................................ 34

Slot X3: CT W1 - Current Transformer Measuring Inputs............................................................................................ 37

Slot X4: CT W2 - Current Transformer Measuring Inputs............................................................................................ 38

Slot X5: Multi Input – Output Card............................................................................................................................... 49

Slot X6: Voltage Measuring Card................................................................................................................................. 55

Slot X100: Ethernet Interface....................................................................................................................................... 61

Slot X103: Data Communication.................................................................................................................................. 63

Slot X104: IRIG-B00X and Supervision Contact.......................................................................................................... 68

Slot X120 - PC Interface.............................................................................................................................................. 70

Control Wiring Diagram......................................................................................................................................... 71

Wiring Diagrams.......................................................................................................................................................... 74

Input, Output and LED Settings............................................................................................................................. 75

Digital Input Configuration........................................................................................................................................... 75

DI-8P X........................................................................................................................................................................ 76

DI-8 X Settings............................................................................................................................................................ 80

Wired Inputs (Aliases)................................................................................................................................................. 84

Relay Output Configuration......................................................................................................................................... 88

RO-4ZI X - Settings..................................................................................................................................................... 91

RO-4 X Settings......................................................................................................................................................... 108

Analog Outputs.......................................................................................................................................................... 125

Analog Inputs............................................................................................................................................................. 130

LED Configuration..................................................................................................................................................... 145

The »System OK (Operational) « LED ...................................................................................................................... 148

LED Settings.............................................................................................................................................................. 149

Front Panel.......................................................................................................................................................... 166

Basic Menu Control................................................................................................................................................... 172

PowerPort-E Keyboard Commands........................................................................................................................... 173

PowerPort-E........................................................................................................................................................ 174

Installation of PowerPort-E........................................................................................................................................ 175

Uninstalling PowerPort-E........................................................................................................................................... 175

Setting up the Connection PC - Device..................................................................................................................... 176

Loading of Device Data When Using PowerPort-E.................................................................................................... 187

www.eaton.com 3

EMR-5000 IM02602012E

Restoring Device Data When Using PowerPort-E..................................................................................................... 187

Backup and Documentation When Using PowerPort-E.............................................................................................188

Printing of Device Data When Using PowerPort-E (Setting List)................................................................................188

Off-line Device Planning Via PowerPort-E................................................................................................................. 190

PowerPort-E Keyboard Commands........................................................................................................................... 191

Measuring Values................................................................................................................................................ 192

Read Out Measured Values...................................................................................................................................... 192

Differential Current - Measured Values...................................................................................................................... 195

Current - Measured Values........................................................................................................................................ 197

Voltage - Measured Values....................................................................................................................................... 200

Power - Measured Values......................................................................................................................................... 204

Energy Counter................................................................................................................................................... 206

Global Parameters of the Energy Counter Module.................................................................................................... 206

Direct Commands of the Energy Counter Module .................................................................................................... 206

Signals of the Energy Counter Module (States of the Outputs)..................................................................................206

Statistics.............................................................................................................................................................. 208

Configuration of the Minimum and Maximum Values................................................................................................. 208

Configuration of the Average Value Calculation......................................................................................................... 209

Direct Commands...................................................................................................................................................... 211

Global Protection Parameters of the Statistics Module..............................................................................................211

States of the Inputs of the Statistics Module.............................................................................................................. 214

Signals of the Statistics Module................................................................................................................................. 215

Counters of the Module Statistics.............................................................................................................................. 215

System Alarms.................................................................................................................................................... 225

Demand Management............................................................................................................................................... 225

Peak Demand............................................................................................................................................................ 228

Min. and Max. Values................................................................................................................................................ 228

THD Protection.......................................................................................................................................................... 228

Device Planning Parameters of the Demand Management.......................................................................................229

Signals of the Demand Management (States of the Outputs)....................................................................................229

Global Protection Parameter of the Demand Management........................................................................................ 230

States of the Inputs of the Demand Management...................................................................................................... 234

Resets................................................................................................................................................................. 235

Manual Acknowledgment........................................................................................................................................... 237

Manual Acknowledgment Via PowerPort-E............................................................................................................... 237

External Acknowledgments....................................................................................................................................... 238

External Acknowledge Via PowerPort-E.................................................................................................................... 238

External LED - Acknowledgment Signals................................................................................................................... 239

Manual Resets........................................................................................................................................................... 249

Manual Resets Via PowerPort-E............................................................................................................................... 249

Reset to Factory Defaults.......................................................................................................................................... 249

Status Display..................................................................................................................................................... 250

Status Display via PowerPort E................................................................................................................................. 250

Operating Panel (HMI)......................................................................................................................................... 251

Special Parameters of the Panel............................................................................................................................... 251

Direct Commands of the Panel.................................................................................................................................. 251

Global Protection Parameters of the Panel................................................................................................................ 251

Recorders............................................................................................................................................................ 252

Waveform Recorder.................................................................................................................................................. 252

www.eaton.com 4

EMR-5000 IM02602012E

Fault Recorder........................................................................................................................................................... 263

Event Recorder.......................................................................................................................................................... 272

Trend Recorder......................................................................................................................................................... 276

Motor Start Recorder................................................................................................................................................. 283

Statistic Recorder...................................................................................................................................................... 289

History Function......................................................................................................................................................... 290

Time Synchronization.......................................................................................................................................... 291

Accuracy of Time Synchronization............................................................................................................................ 292

SNTP......................................................................................................................................................................... 299

IRIG-B00X................................................................................................................................................................. 307

Device Parameters.............................................................................................................................................. 312

Date and Time........................................................................................................................................................... 312

Version...................................................................................................................................................................... 312

Version Via PowerPort-E........................................................................................................................................... 312

TCP/IP Settings......................................................................................................................................................... 313

Direct Commands of the System Module.................................................................................................................. 314

Global Protection Parameters of the System............................................................................................................. 316

System Module Input States...................................................................................................................................... 318

System Module Signals............................................................................................................................................. 319

Special Values of the System Module....................................................................................................................... 320

Communication Protocols.................................................................................................................................... 321

Modbus®................................................................................................................................................................... 321

IEC 61850................................................................................................................................................................. 328

Parameters.......................................................................................................................................................... 343

Parameter Definitions................................................................................................................................................ 343

Access Authorizations (access areas)....................................................................................................................... 358

Passwords – Areas.................................................................................................................................................... 358

How to find out what access areas/levels are unlocked?...........................................................................................362

Unlocking Access Areas............................................................................................................................................ 362

Changing Passwords................................................................................................................................................. 363

Adaptive Parameters via HMI.................................................................................................................................... 364

Access Authorizations (access areas)....................................................................................................................... 367

Passwords – Areas.................................................................................................................................................... 367

How to find out what access areas/levels are unlocked?...........................................................................................371

Unlocking Access Areas............................................................................................................................................ 372

Changing Passwords................................................................................................................................................. 372

Changing Passwords via Power-Port-E..................................................................................................................... 373

Password Entry at the Panel..................................................................................................................................... 373

Password Forgotten ................................................................................................................................................. 373

Parameter Setting at the HMI.................................................................................................................................... 374

Parameter Setting via Power-Port-E.......................................................................................................................... 378

Setting Groups........................................................................................................................................................... 381

Comparing Parameter Files Via PowerPort-E............................................................................................................ 394

Converting Parameter Files Via PowerPort-E............................................................................................................ 395

Program Mode........................................................................................................................................................... 396

System Parameters............................................................................................................................................. 397

General System Parameters..................................................................................................................................... 397

System Parameters – Current Related...................................................................................................................... 398

System Parameters – Voltage Related...................................................................................................................... 399

www.eaton.com 5

EMR-5000 IM02602012E

System Parameters of the Ground Differential..........................................................................................................400

Blocking............................................................................................................................................................... 401

Permanent Blocking.................................................................................................................................................. 401

Temporary Blocking................................................................................................................................................... 401

To Activate or Deactivate the Tripping Command of a Protection Module.................................................................403

Activate, Deactivate Respectively to Block Temporary Protection Functions............................................................404

Protection (Prot) Module...................................................................................................................................... 406

How to Block All Protective and Supervisory Functions............................................................................................. 406

Direct Commands of the Protection Module.............................................................................................................. 413

Global Protection Parameters of the Protection Module............................................................................................413

Protection Module Input States.................................................................................................................................. 414

Protection Module Signals (Output States)................................................................................................................ 414

Values of the Protection Module................................................................................................................................ 415

Switchgear/Breaker – Manager............................................................................................................................ 416

Single Line Diagram.................................................................................................................................................. 417

Switchgear Configuration........................................................................................................................................... 419

Switchgear Wear....................................................................................................................................................... 454

Control - Example: Switching of a Breaker................................................................................................................ 462

Protective Elements............................................................................................................................................. 466

IOC Function............................................................................................................................................................. 466

Load Shedding.......................................................................................................................................................... 467

JAM........................................................................................................................................................................... 472

Locked Rotor Protection............................................................................................................................................ 479

Motor Starting and Control Module............................................................................................................................ 480

Motor Wellness.......................................................................................................................................................... 505

Thermal Model........................................................................................................................................................... 512

Ultimate Trip Current................................................................................................................................................. 523

Underload Module..................................................................................................................................................... 527

87M - Motor Differential Protection............................................................................................................................ 535

50P - DEFT Overcurrent Protection........................................................................................................................... 541

51P - Overcurrent Protection [51, 51C, 51V]............................................................................................................. 552

50R DEFT Calculated Ground Fault Protection Module............................................................................................568

51R INV Calculated Ground Fault Protection............................................................................................................ 579

50X DEFT Measured Ground Fault Protection.......................................................................................................... 589

51X INV Measured Ground Fault Protection.............................................................................................................. 600

50/51X - Ground Fault on X4..................................................................................................................................... 610

Ground Fault Protection............................................................................................................................................. 611

ZI - Zone Interlocking................................................................................................................................................. 612

46 - Current Unbalance Protection............................................................................................................................ 630

27M - Undervoltage Protection.................................................................................................................................. 639

59M - Overvoltage Protection.................................................................................................................................... 649

27A - Auxiliary Undervoltage Protection.................................................................................................................... 658

59A - Auxiliary Overvoltage Protection...................................................................................................................... 665

47 - Voltage Unbalance Protection............................................................................................................................ 672

81O/U, 81R, 78V - Frequency Protection.................................................................................................................. 681

32 - Power Protection................................................................................................................................................ 707

32V - Reactive Power Protection............................................................................................................................... 720

55A and 55D - PF Protection*................................................................................................................................... 733

RT - Remote Trip....................................................................................................................................................... 743

www.eaton.com 6

EMR-5000 IM02602012E

ExP - External Protection........................................................................................................................................... 750

RTD Protection Module............................................................................................................................................. 757

URTDII Module Interface........................................................................................................................................... 785

Supervision.......................................................................................................................................................... 798

BF- Breaker Failure [50BF*/62BF]............................................................................................................................. 798

CTS - Current Transformer Supervision.................................................................................................................... 825

LOP - Loss of Potential.............................................................................................................................................. 832

74TC - Trip Circuit Monitoring.................................................................................................................................... 838

Self Supervision......................................................................................................................................................... 846

Programmable Logic............................................................................................................................................ 849

General Description................................................................................................................................................... 849

Programmable Logic at the Panel.............................................................................................................................. 855

Programmable Logic Via PowerPort-E...................................................................................................................... 855

Commissioning.................................................................................................................................................... 885

Commissioning/Protection Test................................................................................................................................. 886

Decommissioning – Removing the Plug from the Relay............................................................................................887

Service and Commissioning Support................................................................................................................... 888

Maintenance Mode.................................................................................................................................................... 889

Principle – General Use............................................................................................................................................. 889

Before Use................................................................................................................................................................ 890

How to Use the Maintenance Mode........................................................................................................................... 890

Forcing the Relay Output Contacts............................................................................................................................ 892

Disarming the Relay Output Contacts........................................................................................................................ 893

Forcing RTDs*........................................................................................................................................................... 895

Forcing Analog Outputs*............................................................................................................................................ 896

Forcing Analog Inputs*.............................................................................................................................................. 897

Failure Simulator (Sequencer)*.................................................................................................................................. 898

Technical Data.................................................................................................................................................... 923

Climatic Environmental Conditions............................................................................................................................ 923

Degree of Protection EN 60529................................................................................................................................. 923

Routine Test.............................................................................................................................................................. 923

Housing..................................................................................................................................................................... 924

Current and Ground Current Measurement............................................................................................................... 925

Voltage and Residual Voltage Measurement............................................................................................................. 927

Frequency Measurement........................................................................................................................................... 927

Voltage Supply.......................................................................................................................................................... 928

Power Consumption.................................................................................................................................................. 928

Display....................................................................................................................................................................... 929

Front Interface RS232............................................................................................................................................... 929

Real Time Clock........................................................................................................................................................ 930

Digital Inputs.............................................................................................................................................................. 931

Relay Outputs............................................................................................................................................................ 932

Supervision Contact (SC).......................................................................................................................................... 932

Time Synchronization IRIG-B00X.............................................................................................................................. 933

Zone Interlocking....................................................................................................................................................... 934

RS485*...................................................................................................................................................................... 935

Fiber Optic*............................................................................................................................................................... 935

URTD-Interface*........................................................................................................................................................ 935

Analog Outputs.......................................................................................................................................................... 936

www.eaton.com 7

EMR-5000 IM02602012E

Boot Phase................................................................................................................................................................ 937

Standards............................................................................................................................................................ 938

Approvals.................................................................................................................................................................. 938

Design Standards...................................................................................................................................................... 938

High Voltage Tests (IEC 60255-1)............................................................................................................................. 938

EMC Immunity Tests................................................................................................................................................. 939

EMC Emission Tests................................................................................................................................................. 940

Environmental Tests.................................................................................................................................................. 941

Environmental Tests.................................................................................................................................................. 942

Mechanical Tests....................................................................................................................................................... 943

Specifications...................................................................................................................................................... 944

Specifications of the Real Time Clock....................................................................................................................... 944

Time Synchronization Tolerances............................................................................................................................. 944

Specifications of the Measured Value Acquisition...................................................................................................... 945

Protection Elements Accuracy................................................................................................................................... 947

Appendix............................................................................................................................................................. 954

Instantaneous Current Curves (Phase)..................................................................................................................... 964

Time Current Curves (PHASE).................................................................................................................................. 965

Instantaneous Current Curves (Ground Current Calculated).....................................................................................977

Instantaneous Current Curves (Ground Current Measured)......................................................................................979

Time Current Curves (Ground Current)..................................................................................................................... 981

Assignment List................................................................................................................................................... 993

List of ANSI Codes............................................................................................................................................ 1058

md5_1

md5_2

RMS Handoff: 0

File: generated\EMR-5000_user_manual_eaton_en.odt

This manual applies to devices (version):

Version 2.5.a

Build: 23593

www.eaton.com 8

EMR-5000 IM02602012E

Comments on the Manual

This manual gives a general explanation of the tasks of device planning, parameter setting, installation, commissioning,

operation, and maintenance of the Eaton devices.

The manual serves as reference document for:

Engineers in the protection field;

Commissioning engineers;

Personnel dealing with the setting, testing, and maintenance of protection and control devices; and

Well trained personnel involved in electrical installations and power stations.

All functions concerning the type code will be defined. Should there be a description of any functions, parameters, or

inputs/outputs that do not apply to the device in use, please ignore that information.

All details and references are explained to the best of our knowledge and are based on our experience and

observations.

This manual describes the full featured versions of the devices, including all options.

All technical information and data included in this manual reflect their state at the time this document was issued. Eaton

Corporation reserves the right to carry out technical modifications in line with further development without changing this

manual and without previous notice. Therefore no claim can be brought based on the information and descriptions

included in this manual.

Text, graphics, and formulas do not always apply to the actual delivery scope. The drawings and graphics are not true

to scale. Eaton Corporation does not accept any liability for damage and operational failures caused by operating

errors or disregarding the directions of this manual.

No part of this manual is allowed to be reproduced or passed on to others in any form, unless Eaton Corporation has

issued advanced approval in writing.

This user manual is part of the delivery scope when purchasing the device. In case the device is passed on (sold) to a

third party, the manual has to be passed on as well.

Any repair work carried out on the device requires skilled and competent personnel with verifiable knowledge and

experienced with local safety regulations and have the necessary experience with working on electronic protection

devices and power installations.

IMPORTANT DEFINITIONS

The symbol/word combinations detailed below are designed to call the User's attention to issues that could affect User

safety and well being as well as the operating life of the device.

DANGER indicates a hazardous situation which, if not avoided, will result in

death or serious injury.

www.eaton.com 9

EMR-5000 IM02602012E

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION, used with the safety alert symbol, indicates a hazardous situation

which, if not avoided, could result in minor or moderate injury.

CAUTION, without the safety alert symbol, is used to address practices not

related to personal injury.

NOTICE is used to address information and practices not related to personal

injury.

FOLLOW INSTRUCTIONS

Read this entire manual and all other publications pertaining to the work to be

performed before installing, operating, or servicing this equipment. Practice all

plant and safety instructions and precautions. Failure to follow the instructions

can cause personal injury and/or property damage.

PROPER USE

Any unauthorized modifications to or use of this equipment outside its

specified mechanical, electrical, or other operating limits may cause

personal injury and/or property damage, including damage to the

equipment. Any such unauthorized modifications: (1) constitute "misuse"

and/or "negligence" within the meaning of the product warranty, thereby

excluding warranty coverage for any resulting damage; and (2) invalidate

product certifications or listings.

The programmable devices subject to this manual are designed for

protection and also control of power installations and operational devices

that are fed by voltage sources with a fixed frequency, i.e. fixed at 50 or 60

Hertz. They are not intended for use with Variable Frequency Drives. The

devices are further designed for installation in low voltage (LV)

compartments of medium voltage (MV) switchgear panels or in de-

centralized protection panels. The programming and settings have to meet

all requirements of the protection concept (of the equipment that is to be

protected). The User must ensure that the device will properly recognize

and manage (e.g.: switch off the circuit breaker) on the basis of User

selected programming and settings all operational conditions (failures).

Before starting any operation and after any modification of the

programming/settings, make a documented proof that the programming

and settings meet the requirements of the protection concept.

www.eaton.com 10

EMR-5000 IM02602012E

Typical applications for this product family/device line are for example:

Feeder protection;

Mains protection;

Transformer Protection and

Machine protection.

This device is not designed for any usage beyond these applications. This

applies also to the use as a partly completed machinery. The manufacturer

cannot be held liable for any resulting damage. The User alone bears the

risk if this device is used for any application for which it was not designed.

As to the appropriate use of the device: the technical data specified by

Eaton Corporation has to be met.

www.eaton.com 11

EMR-5000 IM02602012E

OUT-OF-DATE PUBLICATION

This publication may have been revised or updated since this copy was

produced. To verify that you have the latest revision, be sure to check the

Eaton Corporation website:

http://www.eaton.com

The latest versions of most publications are available at this site.

If the User's publication is not found on the web site, please contact Eaton

Customer Support to get the latest copy.

www.eaton.com 12

EMR-5000 IM02602012E

ELECTROSTATIC DISCHARGE AWARENESS

All electronic equipment is sensitive to electrostatic discharge, some

components more than others. To protect these components from

electrostatic damage, the User must take special precautions to minimize or

eliminate electrostatic discharges.

Follow these precautions when working with or near the device.

1. Before performing maintenance on the electronic device, discharge

the static electricity on your body to ground by touching and holding a

grounded metal object (pipes, cabinets, equipment, etc.).

2. Avoid the build-up of static electricity on your body by not wearing

clothing made of synthetic materials. Wear cotton or cotton-blend

materials as much as possible because these do not store static

electric charges as much as synthetics.

3. Keep plastic, vinyl, and Styrofoam materials (such as plastic or

Styrofoam cups, cup holders, cigarette packages, cellophane

wrappers, vinyl books or folders, plastic bottles, and plastic ash trays)

away from the device, the modules, and the work area as much as

possible.

4. Do not remove any printed circuit board (PCB) from the device cabinet

unless absolutely necessary. If you must remove the PCB from the

device cabinet, follow these precautions:

Do not touch any part of the PCB except the edges.

Do not touch the electrical conductors, the connectors, or the

components with conductive devices or with your hands.

When replacing a PCB, keep the new PCB in the plastic, anti-static

protective bag it comes in until you are ready to install the PCB.

Immediately after removing the old PCB from the device cabinet,

place it in the anti-static protective bag.

Eaton Corporation reserves the right to update any portion of this publication at any time. Information provided by

Eaton Corporation is believed to be correct and reliable. However, no responsibility is assumed by Eaton Corporation

unless otherwise expressly undertaken.

www.eaton.com 13

EMR-5000 IM02602012E

What Is Included with the Device

The device package includes all connection terminals, except communication connectors, but does not include the

fastening material. Please check the package for completeness upon delivery.

Device Package Contents:

1 – Protective Relay;

1 – Mount (Standard or Projection);

1 – Quick Start Guide; and

2 – CDs

Disk 1 - Contains the User's Manual, Modbus Register Maps, IEC 61850 Communication

Documentation, Wiring Diagrams, and Device Model (Template) for Off-line Parameter Setting;

Disk 2 - Contains PowerPort-E and Quality Manager software applications.

Disk1 contains the device templates. The device templates MUST BE installed

to allow PowerPort-E to configure a device off-line.

Please make sure the product label, wiring diagram, type code, and materials and description pertain to this device. If

you have any doubts, please contact Eaton Corporation's Customer Service Department.

Storage

The devices must not be stored outdoors. If stored, it must be stored in an area with temperature and humidity control

(see the Technical Data section contained in this manual).

Important Information

In line with the customer’s requirement, the devices are combined in a modular

way (in compliance with the order code). The terminal assignment of the

device can be found on the top of the device (wiring diagram). In addition, it

can be found within the Appendix of this manual (see Wiring Diagrams).

www.eaton.com 14

EMR-5000 IM02602012E

Symbols

www.eaton.com 15

Inactive

Active

IG.Dir n poss-

>Nondir Trip

1

2

Setting Value:

<Name>.

I

Device Planning:

<Name>

Signal:

IG

Measured Values:

<Name>.*int Alm L1

Internal message

Functional description: If the setting

value "IG.Block at VG=0" is set to

"inactive", the output 1 is active and

output 2 is inactive. If the setting value

"IG.Block at VE=0" is set to "active",

the output 2 is active and the output 1

is inactive.

Prot.I dir fwd

AR.t-D

0t-D

φ

"

φ

"=Elements with complex functions

"gray-box".

Inactive

Active

Bkr.Latched

Option/features to be realised in the future.

Parameter of a Module-Input with a

SelectionList/DropDown. An (1..n)

signal/output from the list or a pre-

defined value can be selected.

1..n, Assignment List

<Na me>

1..n, VeEnable

No assignment,1..n

No assignment 1

<Na me>

1..n, Assignment List

Parameter of a Module-Input (with

special values): An (1..n) output from the

list will be assigned to the input

"<name>.identifier". If the parameter is

set to "ItemNull", an "inactive"-signal will

be given out.

Limit value monitoring with three

analog input values. Compares 3

analog values with the set limit; output

values are three different binary

values as a result of the comparision.

If the analog signal exceeds the limit I/

In, the corresponding output signal

becomes "1".

I/ In

IA

IB

IC

<20%Vn

V

Limit value monitoring (Compared to

a fixed value). Compares a value with

the fixed set limit; output value is

binary as a result of the comparision.

If the signal exceeds the limit, the

corresponding output signal becomes

"1".

Adaptive Param eter

Selection List

<Name>

Direct Command

EMR-5000 IM02602012E

www.eaton.com 16

And

Or

Negated Input

Negated Output

Band-pass (filter)

IH1

Band-pass (filter)

IH2

Quotient of Analog Values

t1

Delay Timer

1

Bkr.t-TripCmd

t

Analog Values

AND

S Q

R1 Q

a

b

c

d

RS flip-flop

a b c d

0 0 Unchanged

0 1 0 1

1 0 1 0

1 1 0 1

Time stage: A "1" at the

input starts the element. If

the time <name>.t is

expired, the output becomes

"1" too. The time stage will

be reset by "0" at the input.

Thus the output will be set to

"0" at the same time.

Time stage minimum pulse

width: The pulse width

<name>.t will be started if a

"1" is feed to the input. By

starting <name>.t, the

output becomes "1". If the

time is expired, the output

becomes "0" independent

from the input signal.

IH1

IH2

Exclusive-XR

Analog Value

Comparator

+

R

+ Increment

R Reset

Edge triggered counter

IH2

IH1

OR

XOR

Inverting

t2

t1: Switch On Delay

t2: Switch Off Delay

Delay Timer

t1

t2

t1

t2

Counter

EMR-5000 IM02602012E

www.eaton.com 17

2

Input Signal

Output Signal

2

Name.Active

3

Name.Blo TripCmd

4

Name.Active

5

IH2.Blo Phase A

6

IH2.Blo Phase B

7

IH2.Blo Phase C

8

IH2.Blo IG

9

Name. Fault in Projected Direction

10

Name. Fault in Projected Direction

10a

Prot - 50R - Direction Detection

10b

Prot - 50X - Direction Detection

14

15

Name.Trip

1

Prot.Available

Please Refer to Diagram: Blockings

Please Refer to Diagram: Blockings**

Please Refer to Diagram:

Prot

Please Refer to Diagram: Trip Blockings

Please Refer to Diagram: IH2

Please Refer to Diagram: Direction Decision

Phase overcurrent

Please Refer to Diagram: Direction Decision Ground

Fault

Please Refer to Diagram: Direction Decision

Ground Fault

Please Refer to Diagram: Direction Decision

Ground Fault

Name.Pickup

Each pickup of a module (except from

supervision modules but including BF) will

lead to a general pickup (collective pickup).

Each trip of an active, trip authorized

protection module will lead to a general trip.

17b

Name.Trip Phase B

18

Name.Trip Phase C

19

Name.TripCmd

16

Each trip of an active, trip authorized protection module

will lead to a general trip.

Each trip of an active, trip authorized protection module

will lead to a general trip.

Each trip of an active, trip authorized protection module

will lead to a general trip.

Each trip of an active, trip authorized protection module

will lead to a general trip.

16a

Each trip of an active, trip authorized protection module

will lead to a general trip.

16b

Name.Trip Phase A

Each trip of an active, trip authorized protection module

will lead to a general trip.

17

Name.Trip Phase B

Each trip of an active, trip authorized protection module

will lead to a general trip.

17a

Name.Trip Phase B

Each trip of an active, trip authorized protection module

will lead to a general trip.

19a

Name.TripCmd

Each trip of an active, trip authorized protection module

will lead to a general trip.

19b

Name.TripCmd

Each trip of an active, trip authorized protection module

will lead to a general trip.

19c

Name.TripCmd

Each trip of an active, trip authorized protection module

will lead to a general trip.

19d

Name.TripCmd

Each trip of an active, trip authorized protection module

will lead to a general trip.

18a

Name.Trip Phase C

Each trip of an active, trip authorized protection module

will lead to a general trip.

18b

Name.Trip Phase C

Each trip of an active, trip authorized protection module

will lead to a general trip.

11

VTS.Pickup

Please Refer to Diagram: VTS

12a

VTS.Pickup

12b

12c

VTS.VTS.LOP Blo

Please Refer to Diagram: VTS

VTS.VTS.LOP Blo

Please Refer to Diagram: VTS

15a

Name.TripCmd

1

EMR-5000 IM02602012E

www.eaton.com 18

34

Bkr.Pos CLOSE

35

Bkr.Pos OPEN

33

Bkr.State

Please Refer to Diagram: Bkr.Bkr Manager

36

Bkr.Pos Indeterm

37

Bkr.Pos Disturb

Please Refer to Diagram: Bkr.Bkr Manager

20

Name.Trip Phase A

21

Name.Trip Phase B

Each trip of an active, trip authorized protection module

will lead to a general trip.

Each trip of an active, trip authorized protection module

will lead to a general trip.

22

Name.Trip Phase C

23

Name.Trip

Each trip of an active, trip authorized protection module

will lead to a general trip.

Each trip of an active, trip authorized protection module

will lead to a general trip.

25

Name.Pickup IB

26b

Name.Pickup IC

27

Name.Pickup

28

Name.Pickup Phase A

29

Name.Pickup Phase B

24

Name.Pickup IA

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

30

Name.Pickup Phase C

31

Name.Pickup

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

32

Prot.Blo TripCmd

24a

Name.Pickup IA

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

24b

Name.Pickup IA

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

25a

Name.Pickup IB

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

25b

Name.Pickup IB

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

26

Name.Pickup IC

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

26a

Name.Pickup IC

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

27a

Name.Pickup

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

27b

Name.Pickup

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

27c

Name.Pickup

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

27d

Name.Pickup

Each phase selective pickup of a module (I, IG, V, VX

depending on the device type) will lead to a phase

selective general pickup (collective pickup).

38a

Please Refer to Diagram: LOP.LOP Blo

LOP.LOP Blo

38b

Please Refer to Diagram: LOP.Ex FF VT

LOP.Ex FF VT

38c

Please Refer to Diagram: LOP.Ex FF GVT

LOP.Ex FF GVT

EMR-5000 IM02602012E

www.eaton.com 19

41

Bkr.Prot CLOSE

42

Bkr.CLOSE Cmd

Bkr.Prot CLOSE

Bkr.CLOSE Cmd

39

Please Refer to Diagram: Q->&V<.Decoupling Distributed

Generator

Q->&V<.Decoupling Distributed Generator

40

Please Refer to Diagram: CTS.Pickup

CTS.Pickup

44

45

Please Refer to Diagram: Analog Values

43

Please Refer to Diagram: Analog Values

AnIn[1].Value

AnIn[2].Value

AnIn[n].Value

EMR-5000 IM02602012E

www.eaton.com 20

Access Level

Read Only-Lv0

Prot-Lv1

Prot-Lv2

Supervisor-Lv3

Control-Lv1

Control-Lv2

Parameters can only be read within this level.

This level enables to execute Resets and Acknowledgements

This level enables to modify protection settings

This level provides full access (not limited) to all settings

This level enables to control switchtgears

This level enables to modify the settings of switchgears

(Please refer to chapter [Parameter\Access Level])

Page is loading ...

Eaton EMR-5000 Installation, Operation and Maintenance Manual

Related papers

Other documents