Page is loading ...
EMR-4000 - MOTOR RELAY
Installation, Operation and Maintenance
Software-Version: 2.5.a
IM02602009E
Revision: A
English
EMR-4000 IM02602009E
EMR-4000 Functional Overview
www.eaton.com 2
Trend recorder
Event recorder
Current and Volt.:
unbalance
%THD and THD
Fund. and RMS
min./max./avg.
phasors and
angles
Power:
Fund. and RMS
MVA, Mwatt, Mvar,
PF
Metering,
Statistics and
Demand
standard
3
1
3
EMR-4000
74
TC
*
Zone
Interlocking
Breaker Wear
Programmable
Logic
51
50R
46 50J 51P
27A
59A
47
55
A/D
27M 59M
81
U/O
51X
LOP
51V 50X
1
Fault recorder
Waveform recorder
Option
Motor
Load
URTD Assembly
14
Analog
Outputs
51R
37 49S
50P
50
BF
CTS
32
32V
81 R 78V
49
Start recorder
Statistics recorder
History function
66
IRIG-B00X
SNTP
URTD Assembly
EMR-4000 IM02602009E
Table of Contents
EMR-4000 Functional Overview.............................................................................................................................. 2
Table of Contents.................................................................................................................................................... 3
Comments on the Manual........................................................................................................................................ 9
What Is Included with the Device................................................................................................................................. 14
Storage........................................................................................................................................................................ 14
Important Information ................................................................................................................................................. 14
Symbols....................................................................................................................................................................... 15
General Conventions................................................................................................................................................... 21
Load Reference Arrow System.................................................................................................................................... 22
Device................................................................................................................................................................... 23
Device Planning........................................................................................................................................................... 23
Device Planning Parameters of the Device................................................................................................................. 24
Installation and Wiring........................................................................................................................................... 27
Three-Side-View.......................................................................................................................................................... 27
Overview of Slots - Assembly Groups......................................................................................................................... 29
Slot X1: Power Supply Card with Digital Inputs...........................................................................................................31
Slot X2: Relay Output Card - Zone Interlock................................................................................................................ 34
Slot X3: Current Transformer Measuring Inputs.......................................................................................................... 37
Slot X4: Voltage Transformer Measuring Inputs.......................................................................................................... 47
Slot X5: Relay Output Card......................................................................................................................................... 53
Typical Connection Diagrams...................................................................................................................................... 56
Slot X100: Ethernet Interface....................................................................................................................................... 60
Slot X103: Data Communication.................................................................................................................................. 62
Slot X104: IRIG-B00X and Supervision Contact.......................................................................................................... 67
Slot X120 - PC Interface.............................................................................................................................................. 69
Control Wiring Diagram......................................................................................................................................... 70
Wiring Diagrams.......................................................................................................................................................... 73
Input, Output and LED Settings............................................................................................................................. 74
Digital Input Configuration........................................................................................................................................... 74
DI-8P X........................................................................................................................................................................ 75
Wired Inputs (Aliases)................................................................................................................................................. 79
Relay Output Configuration......................................................................................................................................... 83
RO-4ZI X - Settings..................................................................................................................................................... 86
LED Configuration..................................................................................................................................................... 103
The »System OK (Operational) « LED ...................................................................................................................... 106
LED Settings.............................................................................................................................................................. 107
Analog Outputs.......................................................................................................................................................... 124
Front Panel.......................................................................................................................................................... 129
Basic Menu Control................................................................................................................................................... 135
PowerPort-E Keyboard Commands........................................................................................................................... 136
PowerPort-E........................................................................................................................................................ 137
Installation of PowerPort-E........................................................................................................................................ 138
Uninstalling PowerPort-E........................................................................................................................................... 138
Setting up the Connection PC - Device..................................................................................................................... 139
Loading of Device Data When Using PowerPort-E.................................................................................................... 150
Restoring Device Data When Using PowerPort-E..................................................................................................... 150
Backup and Documentation When Using PowerPort-E............................................................................................. 151
www.eaton.com 3
EMR-4000 IM02602009E
Printing of Device Data When Using PowerPort-E (Setting List)................................................................................151
Off-line Device Planning Via PowerPort-E................................................................................................................. 153
PowerPort-E Keyboard Commands........................................................................................................................... 154
Measuring Values................................................................................................................................................ 155
Read Out Measured Values...................................................................................................................................... 155
Current - Measured Values........................................................................................................................................ 158
Voltage - Measured Values....................................................................................................................................... 161
Power - Measured Values......................................................................................................................................... 165
Energy Counter................................................................................................................................................... 167
Global Parameters of the Energy Counter Module.................................................................................................... 167
Direct Commands of the Energy Counter Module .................................................................................................... 167
Signals of the Energy Counter Module (States of the Outputs)..................................................................................167
Statistics.............................................................................................................................................................. 169
Configuration of the Minimum and Maximum Values................................................................................................. 169
Configuration of the Average Value Calculation......................................................................................................... 170
Direct Commands...................................................................................................................................................... 172
Global Protection Parameters of the Statistics Module.............................................................................................. 172
States of the Inputs of the Statistics Module.............................................................................................................. 175
Signals of the Statistics Module................................................................................................................................. 176
Counters of the Module Statistics.............................................................................................................................. 176
System Alarms.................................................................................................................................................... 185
Demand Management............................................................................................................................................... 185
Peak Demand............................................................................................................................................................ 188
Min. and Max. Values................................................................................................................................................ 188
THD Protection.......................................................................................................................................................... 188
Device Planning Parameters of the Demand Management....................................................................................... 189
Signals of the Demand Management (States of the Outputs)....................................................................................189
Global Protection Parameter of the Demand Management........................................................................................190
States of the Inputs of the Demand Management...................................................................................................... 194
Resets................................................................................................................................................................. 195
Manual Acknowledgment........................................................................................................................................... 197
Manual Acknowledgment Via PowerPort-E............................................................................................................... 197
External Acknowledgments....................................................................................................................................... 198
External Acknowledge Via PowerPort-E.................................................................................................................... 198
External LED - Acknowledgment Signals................................................................................................................... 199
Manual Resets........................................................................................................................................................... 209
Manual Resets Via PowerPort-E............................................................................................................................... 209
Reset to Factory Defaults.......................................................................................................................................... 209
Status Display..................................................................................................................................................... 210
Status Display via PowerPort E................................................................................................................................. 210
Operating Panel (HMI)......................................................................................................................................... 211
Special Parameters of the Panel............................................................................................................................... 211
Direct Commands of the Panel.................................................................................................................................. 211
Global Protection Parameters of the Panel................................................................................................................ 211
Recorders............................................................................................................................................................ 212
Waveform Recorder.................................................................................................................................................. 212
Fault Recorder........................................................................................................................................................... 223
Event Recorder.......................................................................................................................................................... 232
Trend Recorder......................................................................................................................................................... 236
www.eaton.com 4
EMR-4000 IM02602009E
Motor Start Recorder................................................................................................................................................. 243
Statistic Recorder...................................................................................................................................................... 249
History Function......................................................................................................................................................... 250
Time Synchronization.......................................................................................................................................... 251
Accuracy of Time Synchronization............................................................................................................................ 252
SNTP......................................................................................................................................................................... 259
IRIG-B00X................................................................................................................................................................. 267
Device Parameters.............................................................................................................................................. 272
Date and Time........................................................................................................................................................... 272
Version...................................................................................................................................................................... 272
Version Via PowerPort-E........................................................................................................................................... 272
TCP/IP Settings......................................................................................................................................................... 273
Direct Commands of the System Module.................................................................................................................. 274
Global Protection Parameters of the System............................................................................................................. 276
System Module Input States...................................................................................................................................... 278
Special Values of the System Module....................................................................................................................... 280
Communication Protocols.................................................................................................................................... 281
Modbus®................................................................................................................................................................... 281
IEC 61850................................................................................................................................................................. 288
Parameters.......................................................................................................................................................... 303
Parameter Definitions................................................................................................................................................ 303
Access Authorizations (access areas)....................................................................................................................... 318
Passwords – Areas.................................................................................................................................................... 318
How to find out what access areas/levels are unlocked?...........................................................................................322
Unlocking Access Areas............................................................................................................................................ 322
Changing Passwords................................................................................................................................................. 323
Adaptive Parameters via HMI.................................................................................................................................... 324
Access Authorizations (access areas)....................................................................................................................... 327
Passwords – Areas.................................................................................................................................................... 327
How to find out what access areas/levels are unlocked?...........................................................................................331
Unlocking Access Areas............................................................................................................................................ 332
Changing Passwords................................................................................................................................................. 332
Changing Passwords via Power-Port-E..................................................................................................................... 333
Password Entry at the Panel..................................................................................................................................... 333
Password Forgotten ................................................................................................................................................. 333
Parameter Setting at the HMI.................................................................................................................................... 334
Parameter Setting via Power-Port-E.......................................................................................................................... 338
Setting Groups........................................................................................................................................................... 341
Comparing Parameter Files Via PowerPort-E............................................................................................................ 353
Converting Parameter Files Via PowerPort-E............................................................................................................ 354
Program Mode........................................................................................................................................................... 355
System Parameters............................................................................................................................................. 356
General System Parameters..................................................................................................................................... 356
System Parameters – Current Related...................................................................................................................... 357
System Parameters – Voltage Related...................................................................................................................... 358
Blocking............................................................................................................................................................... 359
Permanent Blocking.................................................................................................................................................. 359
Temporary Blocking................................................................................................................................................... 359
To Activate or Deactivate the Tripping Command of a Protection Module.................................................................361
www.eaton.com 5
EMR-4000 IM02602009E
Activate, Deactivate Respectively to Block Temporary Protection Functions............................................................362
Protection (Prot) Module...................................................................................................................................... 364
How to Block All Protective and Supervisory Functions............................................................................................. 364
Direct Commands of the Protection Module.............................................................................................................. 371
Global Protection Parameters of the Protection Module............................................................................................ 371
Protection Module Input States.................................................................................................................................. 372
Protection Module Signals (Output States)................................................................................................................ 372
Values of the Protection Module................................................................................................................................ 373
Switchgear/Breaker - Manager............................................................................................................................ 374
Breaker Configuration................................................................................................................................................ 374
Single Line Diagram.................................................................................................................................................. 376
Switching the Breaker at the Panel............................................................................................................................ 399
Breaker Wear............................................................................................................................................................ 401
Control - Example: Switching of a Breaker................................................................................................................ 417
Protective Elements............................................................................................................................................. 420
IOC Function............................................................................................................................................................. 420
Load Shedding.......................................................................................................................................................... 421
JAM........................................................................................................................................................................... 426
Locked Rotor Protection............................................................................................................................................ 432
Motor Starting and Control Module............................................................................................................................ 433
Motor Wellness.......................................................................................................................................................... 458
Thermal Model........................................................................................................................................................... 465
Ultimate Trip Current................................................................................................................................................. 476
Underload Module..................................................................................................................................................... 480
50P - DEFT Overcurrent Protection........................................................................................................................... 487
51P - Overcurrent Protection [51, 51C, 51V]............................................................................................................. 498
50R DEFT Calculated Ground Fault Protection Module............................................................................................514
51R INV Calculated Ground Fault Protection............................................................................................................ 525
50X DEFT Measured Ground Fault Protection.......................................................................................................... 535
51X INV Measured Ground Fault Protection.............................................................................................................. 546
Ground Fault Protection............................................................................................................................................. 556
ZI - Zone Interlocking................................................................................................................................................. 557
46 - Current Unbalance Protection............................................................................................................................ 575
27M - Undervoltage Protection.................................................................................................................................. 584
59M - Overvoltage Protection.................................................................................................................................... 594
27A - Auxiliary Undervoltage Protection.................................................................................................................... 603
59A - Auxiliary Overvoltage Protection...................................................................................................................... 610
47 - Voltage Unbalance Protection............................................................................................................................ 617
81O/U, 81R, 78V - Frequency Protection.................................................................................................................. 626
32 - Power Protection................................................................................................................................................ 652
32V - Reactive Power Protection............................................................................................................................... 666
55A and 55D - PF Protection*................................................................................................................................... 679
RT - Remote Trip....................................................................................................................................................... 689
ExP - External Protection........................................................................................................................................... 696
Ex87 - External Differential Protection....................................................................................................................... 703
RTD Protection Module............................................................................................................................................. 711
URTDII Module Interface........................................................................................................................................... 739
Supervision.......................................................................................................................................................... 753
BF- Breaker Failure [50BF*/62BF]............................................................................................................................. 753
www.eaton.com 6
EMR-4000 IM02602009E
CTS - Current Transformer Supervision.................................................................................................................... 779
LOP - Loss of Potential.............................................................................................................................................. 786
74TC - Trip Circuit Monitoring.................................................................................................................................... 792
Self Supervision......................................................................................................................................................... 800
Programmable Logic............................................................................................................................................ 803
General Description................................................................................................................................................... 803
Programmable Logic at the Panel.............................................................................................................................. 809
Programmable Logic Via PowerPort-E...................................................................................................................... 809
Commissioning.................................................................................................................................................... 837
Commissioning/Protection Test................................................................................................................................. 838
Decommissioning – Removing the Plug from the Relay............................................................................................839
Service and Commissioning Support................................................................................................................... 840
Maintenance Mode.................................................................................................................................................... 841
Principle – General Use............................................................................................................................................. 841
Before Use................................................................................................................................................................ 842
How to Use the Maintenance Mode........................................................................................................................... 842
Forcing the Relay Output Contacts............................................................................................................................ 844
Disarming the Relay Output Contacts........................................................................................................................ 845
Forcing RTDs*........................................................................................................................................................... 847
Forcing Analog Outputs*............................................................................................................................................ 848
Forcing Analog Inputs*.............................................................................................................................................. 849
Failure Simulator (Sequencer)*.................................................................................................................................. 850
Technical Data.................................................................................................................................................... 869
Climatic Environmental Conditions............................................................................................................................ 869
Degree of Protection EN 60529................................................................................................................................. 869
Routine Test.............................................................................................................................................................. 869
Housing..................................................................................................................................................................... 870
Current and Ground Current Measurement............................................................................................................... 871
Voltage and Residual Voltage Measurement............................................................................................................. 873
Frequency Measurement........................................................................................................................................... 873
Voltage Supply.......................................................................................................................................................... 874
Power Consumption.................................................................................................................................................. 874
Display....................................................................................................................................................................... 875
Front Interface RS232............................................................................................................................................... 875
Real Time Clock........................................................................................................................................................ 876
Digital Inputs.............................................................................................................................................................. 877
Relay Outputs............................................................................................................................................................ 878
Supervision Contact (SC).......................................................................................................................................... 878
Time Synchronization IRIG-B00X.............................................................................................................................. 879
Zone Interlocking....................................................................................................................................................... 880
RS485*...................................................................................................................................................................... 881
Fiber Optic*............................................................................................................................................................... 881
URTD-Interface*........................................................................................................................................................ 881
Analog Outputs.......................................................................................................................................................... 882
Boot Phase................................................................................................................................................................ 883
Standards............................................................................................................................................................ 884
Approvals.................................................................................................................................................................. 884
Design Standards...................................................................................................................................................... 884
High Voltage Tests (IEC 60255-1)............................................................................................................................. 884
www.eaton.com 7
EMR-4000 IM02602009E
EMC Immunity Tests................................................................................................................................................. 885
EMC Emission Tests................................................................................................................................................. 886
Environmental Tests.................................................................................................................................................. 887
Environmental Tests.................................................................................................................................................. 888
Mechanical Tests....................................................................................................................................................... 889
Specifications...................................................................................................................................................... 890
Specifications of the Real Time Clock....................................................................................................................... 890
Time Synchronization Tolerances............................................................................................................................. 890
Specifications of the Measured Value Acquisition...................................................................................................... 891
Protection Elements Accuracy................................................................................................................................... 893
Appendix............................................................................................................................................................. 899
Instantaneous Current Curves (Phase)..................................................................................................................... 909
Time Current Curves (PHASE).................................................................................................................................. 910
Instantaneous Current Curves (Ground Current Calculated).....................................................................................922
Instantaneous Current Curves (Ground Current Measured)......................................................................................924
Time Current Curves (Ground Current)..................................................................................................................... 926
Assignment List................................................................................................................................................... 938
List of ANSI Codes.............................................................................................................................................. 996
md5_1
md5_2
RMS Handoff: 0
File: generated\EMR-4000_user_manual_eaton_en.odt
This manual applies to devices (version):
Version 2.5.a
Build: 23598
www.eaton.com 8
EMR-4000 IM02602009E
Comments on the Manual
This manual gives a general explanation of the tasks of device planning, parameter setting, installation, commissioning,
operation, and maintenance of the Eaton devices.
The manual serves as reference document for:
Engineers in the protection field;
Commissioning engineers;
Personnel dealing with the setting, testing, and maintenance of protection and control devices; and
Well trained personnel involved in electrical installations and power stations.
All functions concerning the type code will be defined. Should there be a description of any functions, parameters, or
inputs/outputs that do not apply to the device in use, please ignore that information.
All details and references are explained to the best of our knowledge and are based on our experience and
observations.
This manual describes the full featured versions of the devices, including all options.
All technical information and data included in this manual reflect their state at the time this document was issued. Eaton
Corporation reserves the right to carry out technical modifications in line with further development without changing this
manual and without previous notice. Therefore no claim can be brought based on the information and descriptions
included in this manual.
Text, graphics, and formulas do not always apply to the actual delivery scope. The drawings and graphics are not true
to scale. Eaton Corporation does not accept any liability for damage and operational failures caused by operating
errors or disregarding the directions of this manual.
No part of this manual is allowed to be reproduced or passed on to others in any form, unless Eaton Corporation has
issued advanced approval in writing.
This user manual is part of the delivery scope when purchasing the device. In case the device is passed on (sold) to a
third party, the manual has to be passed on as well.
Any repair work carried out on the device requires skilled and competent personnel with verifiable knowledge and
experienced with local safety regulations and have the necessary experience with working on electronic protection
devices and power installations.
IMPORTANT DEFINITIONS
The symbol/word combinations detailed below are designed to call the User's attention to issues that could affect User
safety and well being as well as the operating life of the device.
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
www.eaton.com 9
EMR-4000 IM02602009E
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION, used with the safety alert symbol, indicates a hazardous situation
which, if not avoided, could result in minor or moderate injury.
CAUTION, without the safety alert symbol, is used to address practices not
related to personal injury.
NOTICE is used to address information and practices not related to personal
injury.
FOLLOW INSTRUCTIONS
Read this entire manual and all other publications pertaining to the work to be
performed before installing, operating, or servicing this equipment. Practice all
plant and safety instructions and precautions. Failure to follow the instructions
can cause personal injury and/or property damage.
PROPER USE
Any unauthorized modifications to or use of this equipment outside its
specified mechanical, electrical, or other operating limits may cause
personal injury and/or property damage, including damage to the
equipment. Any such unauthorized modifications: (1) constitute "misuse"
and/or "negligence" within the meaning of the product warranty, thereby
excluding warranty coverage for any resulting damage; and (2) invalidate
product certifications or listings.
The programmable devices subject to this manual are designed for
protection and also control of power installations and operational devices
that are fed by voltage sources with a fixed frequency, i.e. fixed at 50 or 60
Hertz. They are not intended for use with Variable Frequency Drives. The
devices are further designed for installation in low voltage (LV)
compartments of medium voltage (MV) switchgear panels or in de-
centralized protection panels. The programming and settings have to meet
all requirements of the protection concept (of the equipment that is to be
protected). The User must ensure that the device will properly recognize
and manage (e.g.: switch off the circuit breaker) on the basis of User
selected programming and settings all operational conditions (failures).
Before starting any operation and after any modification of the
programming/settings, make a documented proof that the programming
and settings meet the requirements of the protection concept.
www.eaton.com 10
EMR-4000 IM02602009E
Typical applications for this product family/device line are for example:
Feeder protection;
Mains protection;
Transformer Protection and
Machine protection.
This device is not designed for any usage beyond these applications. This
applies also to the use as a partly completed machinery. The manufacturer
cannot be held liable for any resulting damage. The User alone bears the
risk if this device is used for any application for which it was not designed.
As to the appropriate use of the device: the technical data specified by
Eaton Corporation has to be met.
www.eaton.com 11
EMR-4000 IM02602009E
OUT-OF-DATE PUBLICATION
This publication may have been revised or updated since this copy was
produced. To verify that you have the latest revision, be sure to check the
Eaton Corporation website:
http://www.eaton.com
The latest versions of most publications are available at this site.
If the User's publication is not found on the web site, please contact Eaton
Customer Support to get the latest copy.
www.eaton.com 12
EMR-4000 IM02602009E
ELECTROSTATIC DISCHARGE AWARENESS
All electronic equipment is sensitive to electrostatic discharge, some
components more than others. To protect these components from
electrostatic damage, the User must take special precautions to minimize or
eliminate electrostatic discharges.
Follow these precautions when working with or near the device.
1. Before performing maintenance on the electronic device, discharge
the static electricity on your body to ground by touching and holding a
grounded metal object (pipes, cabinets, equipment, etc.).
2. Avoid the build-up of static electricity on your body by not wearing
clothing made of synthetic materials. Wear cotton or cotton-blend
materials as much as possible because these do not store static
electric charges as much as synthetics.
3. Keep plastic, vinyl, and Styrofoam materials (such as plastic or
Styrofoam cups, cup holders, cigarette packages, cellophane
wrappers, vinyl books or folders, plastic bottles, and plastic ash trays)
away from the device, the modules, and the work area as much as
possible.
4. Do not remove any printed circuit board (PCB) from the device cabinet
unless absolutely necessary. If you must remove the PCB from the
device cabinet, follow these precautions:
Do not touch any part of the PCB except the edges.
Do not touch the electrical conductors, the connectors, or the
components with conductive devices or with your hands.
When replacing a PCB, keep the new PCB in the plastic, anti-static
protective bag it comes in until you are ready to install the PCB.
Immediately after removing the old PCB from the device cabinet,
place it in the anti-static protective bag.
Eaton Corporation reserves the right to update any portion of this publication at any time. Information provided by
Eaton Corporation is believed to be correct and reliable. However, no responsibility is assumed by Eaton Corporation
unless otherwise expressly undertaken.
© Eaton Corporation, 2014. All Rights Reserved.
www.eaton.com 13
EMR-4000 IM02602009E
What Is Included with the Device
The device package includes all connection terminals, except communication connectors, but does not include the
fastening material. Please check the package for completeness upon delivery.
Device Package Contents:
1 – Protective Relay;
1 – Mount (Standard or Projection);
1 – Quick Start Guide; and
2 – CDs
Disk 1 - Contains the User's Manual, Modbus Register Maps, IEC 61850 Communication
Documentation, Wiring Diagrams, and Device Model (Template) for Off-line Parameter Setting;
Disk 2 - Contains PowerPort-E and Quality Manager software applications.
Disk1 contains the device templates. The device templates MUST BE installed
to allow PowerPort-E to configure a device off-line.
Please make sure the product label, wiring diagram, type code, and materials and description pertain to this device. If
you have any doubts, please contact Eaton Corporation's Customer Service Department.
Storage
The devices must not be stored outdoors. If stored, it must be stored in an area with temperature and humidity control
(see the Technical Data section contained in this manual).
Important Information
In line with the customer’s requirement, the devices are combined in a modular
way (in compliance with the order code). The terminal assignment of the
device can be found on the top of the device (wiring diagram). In addition, it
can be found within the Appendix of this manual (see Wiring Diagrams).
www.eaton.com 14
EMR-4000 IM02602009E
Symbols
www.eaton.com 15
Inactive
Active
IG.Dir n poss-
>Nondir Trip
1
2
Setting Value:
<Name>.
I
Device Planning:
<Name>
Signal:
IG
Measured Values:
<Name>.*int Alm L1
Internal message
Functional description: If the setting
value "IG.Block at VG=0" is set to
"inactive", the output 1 is active and
output 2 is inactive. If the setting value
"IG.Block at VE=0" is set to "active",
the output 2 is active and the output 1
is inactive.
Prot.I dir fwd
AR.t-D
0t-D
φ
"
φ
"=Elements with complex functions
"gray-box".
Inactive
Active
Bkr.Latched
Option/features to be realised in the future.
Parameter of a Module-Input with a
SelectionList/DropDown. An (1..n)
signal/output from the list or a pre-
defined value can be selected.
1..n, Assignment List
<Na me>
1..n, VeEnable
No assignment,1..n
No assignment 1
<Na me>
1..n, Assignment List
Parameter of a Module-Input (with
special values): An (1..n) output from the
list will be assigned to the input
"<name>.identifier". If the parameter is
set to "ItemNull", an "inactive"-signal will
be given out.
Limit value monitoring with three
analog input values. Compares 3
analog values with the set limit; output
values are three different binary
values as a result of the comparision.
If the analog signal exceeds the limit I/
In, the corresponding output signal
becomes "1".
I/ In
IA
IB
IC
<20%Vn
V
Limit value monitoring (Compared to
a fixed value). Compares a value with
the fixed set limit; output value is
binary as a result of the comparision.
If the signal exceeds the limit, the
corresponding output signal becomes
"1".
Adaptive Param eter
Selection List
<Name>
Direct Command
EMR-4000 IM02602009E
www.eaton.com 16
And
Or
Negated Input
Negated Output
Band-pass (filter)
IH1
Band-pass (filter)
IH2
Quotient of Analog Values
t1
Delay Timer
1
Bkr.t-TripCmd
t
Analog Values
AND
S Q
R1 Q
a
b
c
d
RS flip-flop
a b c d
0 0 Unchanged
0 1 0 1
1 0 1 0
1 1 0 1
Time stage: A "1" at the
input starts the element. If
the time <name>.t is
expired, the output becomes
"1" too. The time stage will
be reset by "0" at the input.
Thus the output will be set to
"0" at the same time.
Time stage minimum pulse
width: The pulse width
<name>.t will be started if a
"1" is feed to the input. By
starting <name>.t, the
output becomes "1". If the
time is expired, the output
becomes "0" independent
from the input signal.
IH1
IH2
Exclusive-XR
Analog Value
Comparator
+
R
+ Increment
R Reset
Edge triggered counter
IH2
IH1
OR
XOR
Inverting
t2
t1: Switch On Delay
t2: Switch Off Delay
Delay Timer
t1
t2
t1
t2
Counter
EMR-4000 IM02602009E
www.eaton.com 17
2
2
Input Signal
Output Signal
2
Name.Active
3
Name.Blo TripCmd
4
Name.Active
5
IH2.Blo Phase A
6
IH2.Blo Phase B
7
IH2.Blo Phase C
8
IH2.Blo IG
9
Name. Fault in Projected Direction
10
Name. Fault in Projected Direction
10a
Prot - 50R - Direction Detection
10b
Prot - 50X - Direction Detection
14
15
Name.Trip
1
Prot.Available
Please Refer to Diagram: Blockings
Please Refer to Diagram: Blockings**
Please Refer to Diagram:
Prot
Please Refer to Diagram: Trip Blockings
Please Refer to Diagram: IH2
Please Refer to Diagram: IH2
Please Refer to Diagram: IH2
Please Refer to Diagram: IH2
Please Refer to Diagram: Direction Decision
Phase overcurrent
Please Refer to Diagram: Direction Decision Ground
Fault
Please Refer to Diagram: Direction Decision
Ground Fault
Please Refer to Diagram: Direction Decision
Ground Fault
Name.Pickup
Each pickup of a module (except from
supervision modules but including BF) will
lead to a general pickup (collective pickup).
Each trip of an active, trip authorized
protection module will lead to a general trip.
17b
Name.Trip Phase B
18
Name.Trip Phase C
19
Name.TripCmd
16
Each trip of an active, trip authorized protection module
will lead to a general trip.
Each trip of an active, trip authorized protection module
will lead to a general trip.
Each trip of an active, trip authorized protection module
will lead to a general trip.
Each trip of an active, trip authorized protection module
will lead to a general trip.
16a
Each trip of an active, trip authorized protection module
will lead to a general trip.
16b
Name.Trip Phase A
Each trip of an active, trip authorized protection module
will lead to a general trip.
17
Name.Trip Phase B
Each trip of an active, trip authorized protection module
will lead to a general trip.
17a
Name.Trip Phase B
Each trip of an active, trip authorized protection module
will lead to a general trip.
19a
Name.TripCmd
Each trip of an active, trip authorized protection module
will lead to a general trip.
19b
Name.TripCmd
Each trip of an active, trip authorized protection module
will lead to a general trip.
19c
Name.TripCmd
Each trip of an active, trip authorized protection module
will lead to a general trip.
19d
Name.TripCmd
Each trip of an active, trip authorized protection module
will lead to a general trip.
18a
Name.Trip Phase C
Each trip of an active, trip authorized protection module
will lead to a general trip.
18b
Name.Trip Phase C
Each trip of an active, trip authorized protection module
will lead to a general trip.
11
VTS.Pickup
Please Refer to Diagram: VTS
12a
VTS.Pickup
12b
12c
VTS.VTS.LOP Blo
Please Refer to Diagram: VTS
VTS.VTS.LOP Blo
Please Refer to Diagram: VTS
Please Refer to Diagram: VTS
15a
Name.TripCmd
1
EMR-4000 IM02602009E
www.eaton.com 18
34
Bkr.Pos CLOSE
35
Bkr.Pos OPEN
33
Bkr.State
Please Refer to Diagram: Bkr.Bkr Manager
Please Refer to Diagram: Bkr.Bkr Manager
Please Refer to Diagram: Bkr.Bkr Manager
36
Bkr.Pos Indeterm
37
Bkr.Pos Disturb
Please Refer to Diagram: Bkr.Bkr Manager
Please Refer to Diagram: Bkr.Bkr Manager
20
Name.Trip Phase A
21
Name.Trip Phase B
Each trip of an active, trip authorized protection module
will lead to a general trip.
Each trip of an active, trip authorized protection module
will lead to a general trip.
22
Name.Trip Phase C
23
Name.Trip
Each trip of an active, trip authorized protection module
will lead to a general trip.
Each trip of an active, trip authorized protection module
will lead to a general trip.
25
Name.Pickup IB
26b
Name.Pickup IC
27
Name.Pickup
28
Name.Pickup Phase A
29
Name.Pickup Phase B
24
Name.Pickup IA
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
30
Name.Pickup Phase C
31
Name.Pickup
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
32
Prot.Blo TripCmd
24a
Name.Pickup IA
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
24b
Name.Pickup IA
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
25a
Name.Pickup IB
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
25b
Name.Pickup IB
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
26
Name.Pickup IC
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
26a
Name.Pickup IC
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
27a
Name.Pickup
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
27b
Name.Pickup
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
27c
Name.Pickup
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
27d
Name.Pickup
Each phase selective pickup of a module (I, IG, V, VX
depending on the device type) will lead to a phase
selective general pickup (collective pickup).
38a
Please Refer to Diagram: LOP.LOP Blo
LOP.LOP Blo
38b
Please Refer to Diagram: LOP.Ex FF VT
LOP.Ex FF VT
38c
Please Refer to Diagram: LOP.Ex FF GVT
LOP.Ex FF GVT
EMR-4000 IM02602009E
www.eaton.com 19
41
Bkr.Prot CLOSE
42
Bkr.CLOSE Cmd
Bkr.Prot CLOSE
Bkr.CLOSE Cmd
39
Please Refer to Diagram: Q->&V<.Decoupling Distributed
Generator
Q->&V<.Decoupling Distributed Generator
40
Please Refer to Diagram: CTS.Pickup
CTS.Pickup
44
45
Please Refer to Diagram: Analog Values
Please Refer to Diagram: Analog Values
43
Please Refer to Diagram: Analog Values
AnIn[1].Value
AnIn[2].Value
AnIn[n].Value
EMR-4000 IM02602009E
www.eaton.com 20
Access Level
Read Only-Lv0
Prot-Lv1
Prot-Lv2
Supervisor-Lv3
Control-Lv1
Control-Lv2
Parameters can only be read within this level.
This level enables to execute Resets and Acknowledgements
This level enables to modify protection settings
This level provides full access (not limited) to all settings
This level enables to control switchtgears
This level enables to modify the settings of switchgears
(Please refer to chapter [Parameter\Access Level])
/
