Sony KV-35S45 Owner's manual

Brand: Sony

Model: KV-35S45

Category: LCD TVs

Type: Owner's manual

SON3t:

3-862-568-21

Trinitron" Color TV

Operating Instructions

KV-32S40 KV-32V40 KV-35S40

KV-32S45 KV-32V65 KV-35S45

KV-32S65 KV-35S65

KV-35V65

WARNING

TO prevent fire or shock hazard, do not expose the TV

to fain of f_oistut'e,

ATTIENTION

RPSOUEDECHOCELECTRIQUE,

NEPASOUVRIR

PRECAUClON

RIE_O OE CHC_UE ELECTRICO

NOABRIR

DO NOT REMOVE COVE_ CG_BACK)

_0 USER SERVICEABLE PA_S I_S_DE

_EFER 5ERVlCING TO OUAUFJEDSERVICE pERSOnNEL

This symbol is intended to alert the user to

the presence of unlnsulated "dangerous

voltage" within the product's enclosure that

may be of sufficient magnitude to constitute

a risk of electric shock to persons.

This syr_bQ( is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appbance.

CAUTION

TO PREVENTELECTRICSHOCK,DO NOT USETHIS

POLARIZEDAC PLUGWiTH AN EXTENSIONCORD,

RECEPTACLE.OROTHER OUTLETUNLESSTHEBLADESCAN

BEFULLYINSERTEDTO PREVENTBLADEEXPOSURE.

CAUTION

When using TV games, computers, and similar products

with your TV, keep the brightness and picture contrast

functions at tow settings, if a fixed (non-moving)

pattern is left on the screen for long periods of time at

a high brightness or picture contrast setting, the image

can be permanently imprinted onto the screen.

Continuously watching the same program can cause

the imprint of station _ogos onto the TV screen. These

types of imprints are not covered by your warranty

because they are the result of misuse.

Note on Caption Vision

This television receiver provides display of television

closed captioning in accordance with §15.119 of the

FCCrules.

Note on cleaning the TV

Clean the TV with a soft dry cloth. Never use strong

solvents such as thinner or benzine, which might

damage the finish of the cabinet,

Note to CATV system installer

This reminder is provided to caU the CATV system

installer's attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

Use of this television receiver for other than private

viewing of programs broadcast on UHF or VHF or

transmitted by cable companies for the use of the

general public may require authorization from the

broadcaster/cable company and/or program owner.

NOTIFICATION

This equipment has been tested and found to comply

with the timlts for a ClassB digital device pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residentiaJ instagation. This

equipment generates, uses, and can radiate radio

fTeq_ency energy and, if not installed and used in

accordance with the instructions, may cause harmful

inteference with radio communications. However,

there is no guarantee that Interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antennas.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that airy changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

This document is for the remote controls

RM-Y165/Y167.

MODELS: KV-32S40, 32S45, 32S65, 321/40, 32V65,

35S40, 35S45, 35565, 351/65

As an ENERGY STAR ® Partner,

Sony has determined that this

product or product models meets

the ENERGY STAR • guidelines

for energy efficiency.

ENERGY STARe ls a U.S. registered mark.

Remote Control

In the instructions that follow, we will refer

to the buttons on your remote control. Model

shown is RM-Y167, your remote control may

not look like the one illustrated.

Keepthisflap unfolded and lookto this page

for reference. SYSTEM OFF

(page

TV/VTR

(page 16}

DISPLAY

SLEEP

JUMP --

@ TV/DBS --

(page 16)

RESET

(page 22, 23, and 25)

VOL +/-

CODE SET --

(page 30-32)

SONY

MUTING

TV (POWER)

TV (FUNCTION)

PiP (page 17-19)

TV/VIDEO

-- ANT (page 5 and 16)

-- 0- 9 buttons

-- ENTER

MTS/GUIDE (page 24)

Select buttons

(page 13 and 20)

CH +/-

Getting to know the buttons on the

remote control

Names of the buttons on the remote control are

presented in different colors to represent the

available functions,

Button color

Transparent ......... Press to select the component

you want to control; e.g.

VTR (VCR)/DVD, DBS (Direct

Broadcast Satellite)/CABLE,

orTV

Green ............... Buttons relevant to power

operations, like turning the

TV, DBS (Direct Broadcast

Satellite)/CABLE, or

VTR (VCR)/DVD on or off

Label color

White ............... TV/VTR (VCR)/DVD/DBS

(Direct Broadcast Satellite)/

CABLE operation buttons

Yellow ............... PIP operation butt m_

Blue ................. DBS (Direct Broadcast

Satellite) operation buttons

Green ............... SYSTEM OFF operation button

For a detailed eaplana tiolt of most buttons, see

"l_ t, hinq the FV" on tm_e 15.

Table of Contents

Welcome! ........................................ 3

Precautions ...................................... 3

Using This Manual .......................... 3

Connecting and Installing the TV

Making Connections ....................................... 4

Cable or Anten, na Connections ...................... 5

Connecting directly to cable

or an antenna ................................... 5

Cable and antenna ................................. 5

Cable Box Cormections ................................... 6

Cable box ................................................. 6

Cable box and cable ............................... 6

VCR Connections ............................................. 7

Connecting an antenna/cable TV

system with a VCR .......................... 7

Connecting a VCR and TV with a

cable box ........................................... 7

DBS Connections ............................................. 8

Connecting a DBS receiver ................... 8

Connecting a DBS receiver

and a VCR ......................................... 8

Additional Connections .................................. 9

Connecting a DVD Player .................... 9

Connecting an audio system ................ 9

Connecting an A/V receiver .............. 10

Connecting two VCRs ......................... 10

Connecting a camcorder ..................... 11

S-link Connections ........................................ 12

Connecting S-Link to a VCR .............. 12

Connecting S-Link to a DBS ............... 12

Basic Set Up

Inserting batteries .......................................... 13

Using the remote control move &

select buttons .................................. 13

On-screen help/instructions ........................ 13

Using Your New TV

Setting up the "IV automatically .................. 14

Watching the TV ............................................ 15

Watching two programs at one

time-PIP .......................................... 17

Single Tuner PIP ................................... 17

Dual Tuner PIP ..................................... 19

Using Your Menus

Learning menu selection .............................. 20

Quick start to the menus ............................... 21

Using the VIDEO [_ menu ......................... 22

Using the AUDIO _ menu .......................... 23

Using the TIMER @ menu ......................... 25

Using the SET UP _ menu ....................... 26

Using the BASIC _3 menu ......................... 29

Operating Video Equipment

Programming the remote control ................ 30

Operating a Cable Box or DBS

Receiver

Programming the remote control ................ 32

Troubleshooting ........................... 33

Specifications ................................ 34

Index .............................................. 36

_W Welcome!

l-_CoJt!O .S

Using This Manual

Thank you for purchasing the Sony

Trinitron _"Color TV. This manual is written

for the models listed below. Before reading,

check the model number located on the front

of this manual or on the rear of your TV.

Model KV-35S45 is used for menu and

illustration purposes. Differences in

operation are indicated in the text; for

example, "KV-35S45 only".

,od,,/Z!//i/,I/

-Jl,J,J'!

KV-32S65 • • •

KV-32V65 • • • •

KV-35S45 •

_v-3sv6sL I • I " L _" ! " I

Safety

• Operate the TV only with 120 V AC.

• The plug is designed, for safety purposes,

to fit in the wall outlet only one way. If

you are unable to insert the plug fully into

the outlet, contact your dealer.

• If any liquid or solid object should fall

inside the cabinet, unplug the TV

immediately and have it checked by

qualified personnel before operating it

further.

• If you will not be using the TV for several

days, disconnect power by pulling the

plug itself. Never pull on the cord.

For details concerning safety precautions, see the

supplied leaflet "IMPORTANT SAFEGUARDS".

Installing

• To prevent internal heat build-up, do not

block the ventilation openings.

• Do not install the TV in a hot or humid

place, or in a place subject to excessive

dust or mechanical vibration.

This manual is divided into four major

sections. We recommend that you carefully

review the contents of each section in the

order presented to ensure that you fully

understand the operation of your new TV.

1 Connecting and Installing the TV

This section guides you through your

initial set up. It shows how to connect to

your antenna or cable, and connect any

accessories or components.

2 Basic Set Up

This section teaches you the basic skills

needed to operate your new TV. It shows

you how to operate special functions of

the remote control.

Using your New TV

This section shows you how to begin

using your new TV. It shows how to use

the Easy Set Up Guide feature, and how to

use your remote control.

4 Using your Menus

This section teaches you how to access

on-screen menus and adjust your TV's

settings.

Instructions in this manual are written for the

remote control. Similar controls may befound on

the TV console.

Connecting and Installing the TV

Making Connections

Refer to the table below, it will direct you to the diagram suitable to the comporlents you will be

connecting.

! If you will b_ cor_w_tjng ..... £_ _, ,

Cable or antenna only 5

Cable and antenna (KV-32S65, 32V65, 35S65, 35V65 only) 5

Cable box 6

Cable box and cable to view scrambled channels (KV-32S65, 32V65, 35S65,

35V65 only) 6

VCR and cable or antenna 7

VCR and cable box 7

Direct Broadcast Satellite Receiver (DBS) 8

VCR and Direct Broadcast Satellite Receiver (DBS) 8

Digital Versatile Disc player (DVD) 9

Audio system 9

A / V receiver 10

T*'_oVCR's for tape editing {KV-32V40, 32V65, 35V65 only) 10

Camcorder to view tapes 11

S-Link connections (KV-32S65, 32V65, 35S65, 35V65 only) 12

Cable or Antenna Connections

Connecting directly to cable or an

antenna

The connection you choose will depend on the

cable found in your home. Newer homes will

be equipped with standard coaxial cable

(see A); older homes will probably have

300-ohm twin lead cable (see B); still other

homes may contain both (see C).

• VHF only

• VHF/UHF

• Cable

7S-ohm (Rear of TV)

coaxialcable VHF/UHF

300-ohm twin (Rear of TV)

• VHF only lead cable VHF/UHF

• UHF only

• VHF/UF_F

Antenna connector

7S-ohm coaxial cable

• VHF _ ""_

_J_ (Rear of TV)

ond

EAC-66 U/V mixer

Inot supplied)

• UHF _J

300-ohm twin lead cable

Cable and antenna

• KV-32S65,32V65,35S65,35V65 only

If your cable provider does not feature local

channels, you may find this set up convenient

for viewing both local and cable channels.

Select cable or antenna mode by pressing

ANT on the remote control. You will be able

to alternate between the two input sources.

(Rearof TV)

CATVcable AUX

(No connection "TO TO CONVERTER_._

CONVERTER" in this case)

Note

• In order to receive channels with an

antenr_a, you will need to turn your CABLE

to OFF (see page 26) and perform the

AUTO PROGRAM function.

Antenna cable

VHF/UHF

Connecting and Installing the TV (continued)

Cable Box Connections

Some pay cable TV systems use scrambled or

encoded signals that require a cable box to

view all channels.

Cable box

1 Connect the coaxial connector from your

cable to the IN on your cable box.

2 Using a coaxial cable, connect OUT on

your cable box to VHF/UHF on your TV.

If you will be controlling all channel selection

through your cable box, you should consider using

the CHANNEL FIX feature discussed on page 26.

(Rear of TV)

Cable VHF/UHF

IN _-_OUT

Cable box

Cable box and cable

• KV-32S65, 32V65, 35S65, 35V65 only

For this set up, you can switch between

scrambled channels (through your cable box),

and normal (CATV) channels by pressing

ANT on your remote control.

Notes

• Your Sony remote control can be

programmed to operate your cable box.

(see page 32)

• When using PIP, you cannot view the

AUX input in the window picture.

lip "4"

PressingANT switches between these inputs,

If you are connecting a cable box through the AUX input and would [

like to switch between the A UX and normal (CATV) input you should

consider using the CHANNEL FIX feature discussed on page 26.

Cab{e I_.x (Rear of TV)

_ AUX

channels..._ ]_C_=z]_:_ TO-CONvERTER

75-ohm coaxial ,_(signal)

cable (not supplied) VHF/UHF

CATVcable

(unscrambted channets)

VCR Connections

Connecting an antenna/cable TV

system with a VCR

1 Attach the coaxial connector from your cable

or antenna to IN on your VCR.

2 Using A/V connectors, connect AUDIO and

VIDEO OUT on your VCR to AUDIO and

VIDEO IN on your TV.*

3 Using a coaxial connector, connect OUT on

your VCR to VHF/UHF on your TV.

" If you are connecting a monaural VCR, connect only the

single white audio output to the left input on your TV,

Connecting a VCR and TV with a

cable box

You will need a splitter (not supplied) for the

following con_ection.

1 Connect the single (input) jack of the splitter

to your incoming cable connection. Connect

the other two (output) jacks (using coaxial

cable) to IN on your cable box and VHF/UHF

on your TV.

2 Using a coaxial connector, connect OUT on

your cable box to IN on your VCR.

3 Using A/V connectors, connect AUDIO and

VIDEO OUT on your VCR to AUDIO and

VIDEO IN on your TV.

Disconnect all power sources before making any connections.

VCRmust be connected and

turned on to operate PIP

(KV-32S4_, 3S$45 only).

Coaxial cable

VCR

(Rear of TV)

VMC-810S/820S (not supplied)

[red)

(white)

lyellow)

For optimum picture quality, use S WDEO instead of I

the yellow A/V cable. $ Wdeo does not provide sound,

your audio connectors must still be connected.

Coaxialcable

VCR

T 6°I

Cable

Splitter Cable box

(not supplied)

(Rear of TV)

'_ 1

w_u._ '

AUDIO-R(red)

AUDIO-L (white)

VIDEO (yellow)

VMC-810S/820S (not supplied)

Ill

Connecting and Installing the TV (continued)

Disconnect all power sources before making any connections.

DBS Connections

Connecting a DBS (Direct

Broadcast Satellite) receiver

1 Connect the cable from ),our satellite

antenna to your DBS receiver.

2 Attach the coaxial connector from your

cable or antenna to VHF]UHF on your TV.

3 Using A/V connectors, connect AUDIO

and VIDEO OUT on vour DBS receiver to

AUDIO and VIDEO IN on your TV.

Connecting a DBS (Direct Broadcast

Satellite) receiver and a VCR

1 Connect the cable from your satellite

antenna to your DBS receiver.

2 Attach the coaxial connector from your

cable or antenna to VHF/UHF IN on your

VCR.

3 Using a coaxial connector, connect

VHF/UHF OUT on your VCR to

VHF/UHF on your TV.

4 Using A/V connectors, connect AUDIO

and VIDEO OUT on your DBS receiver to

AUDIO and VIDEO IN on your VCR.

5 Using A/V connectors, connect AUDIO

and VIDEO OUT on your VCR to AUDIO

and VIDEO IN on your TV

Cable/Antenna

For optimum picture quality, use S VIDEO |

instead of the yellow A/V cable. S Video does 2 I

not provide sound, your audio connectors |

must still be connected, i I

OBS receiver

1 b,*_.... v.,,_ I

antenna [ .... _-_ I

cable w • •

(Rear of TV)

_ AUDIO2L (white)

-'- VIDEO (yellow)

VMC-810S/820S (not supplied)

DBS receiver

Pressing TV/VIDEO on the remote

control will allow you to view from

the DBS or VCR.

Cable/Antenna

(Rear of TV)

IHF AUO_Oj T

AUDIO-R (red)

_ _ AUDIO-I. (whitel

_ VIDEO (yellow)

VMC-810S/820S (not supp}ied)

Additional Connections

The following connections are for accessories

that will enhance your viewing options.

Connecting a DVD Player

1 Using A/V connectors, connect LINE OUT

on your DVD to VIDEO IN on your TV.

Disconnect all power sources before making any connections.

For optimum picture quality, use S VIDEO

instead of the yellow AIV cable. S Video

does not provide sound, your audio

connectors must still be connected.

(Rear of DVD player)

UNE _

(Rear of TV)

...... 22o ,

I e_4@@,_ _ /I

_ AUDIO-R (red)

AUDIO-L (white)

VIDEO (yellow)

VMC-810S/820S (not supplied)

Connecting an audio system

For enhanced sound, connect your audio

system to your TV.

1 Using AUDIO connectors, connect AUDIO

OUT on your TV to one of the unused line

inputs (e.g. TV, AUX, TAPE 2) on your

stereo.

2 Set your stereo to the chosen line input.

Refer to page 24 of this manual for

additional audio setup instructions.

(Rear of TV)

I o_t_@_®V_"/[ Auo,o-,(white}

L _! AUDIO.R(red)

RK-74A

/not supplied)

Connecting and Installing the TV (continued)

Connecting an AN receiver

• KV-32V65, 35V65 only

1 Using A/V cables, cormect TV OUT on your

"IV to TV IN on your A/V receiver.

2 Using a single video connector, connect

Monitor OUT on your A/V receiver to

VIDEO 1 IN on your TV.

Tip "_"

You may want to use CHANNELFIXto set your TV's

input to the A/V receiver.Seepage 26.

Connecting two VCRs

• KV-32V40, 32V65, 35V65 only

MONITOR OUT gives you the ability to use a

second VCR to record a program being played

by the primary VCR or to perform tape

editing and dubbing.

] Connect the VCR intended for playback

using the setup instructions on page 7 of

this manual.

2 Using A/V connectors, connect AUDIO

and VIDEO IN on your VCR intended for

recording to MONITOR AUDIO and

VIDEO OUT on your TV.

Disconnect all power sources before making any connections.

VIDEO (

VMC+IOHG/30HG (not supplied)

A/V outputs

A/V receiver

putt

VMC-810S/820S (not supplied)

You cannot change video

inputs while editing using

MONITOR OUT.

(Rear of KV-35V65)

VCRifo: piiyba{k)

VMC 8!05/820b (rl_t supplied)

VCR (for recording)

2_j__ {: _ VIDEO (yellow)

AUDIO-L (white)

__ AUDIO-R (red)

VMC-81051820S (not supplied)

Connecting a camcorder

This coruxection is convenient for viewing a

picture directly from your camcorder.

Using A/V connectors, connect AUDIO and

VIDEO OUT on your camcorder to AUDIO

and VIDEO IN on your TV.

Connection can also be made directly to your

A/V input located on the rear of your 'IV.

Note

• If you are connecting a monaural camcorder,

connect only the single white audio output

to the left input on your "IV.

Disconnect all power sources before making any connections.

I Ifyou have an S VIDEO equipped I

camcorder, you can use an $ Video

I cable for optimum picture quality. I

(Front o_ KV-32V40*, 32V65, 35V65 on_y)

VIDEO (yellow) _ _ _-- AUDIO-R (red)

!_ _-- AUDIO-L (white)

__=_AV output r T

(not suppl_ed)

• KV-32V40 does Jzothave S VIDEO on the front panel

Connecting and Installing the TV (continued)

S-Link connections

• KV-32S65, 32V65, 35S65, 35V65 only

S-Link is designed to allow your Sony

components to "communicate".

Connecting S-Link to a VCR

S-Link will automatically power on the TV

and switch to the correct video input when a

tape is inserted in the VCR.

1 Using A/V connectors, connect AUDIO

and VIDEO OUT on your VCR to AUDIO

and VIDEO IN on your TV.

2 Using an S-Link connector (mono mini

plug), connect S-LINK/CONTROL S-IN on

your VCR to S-LINK on your TV.

Disconnect all power sources before making any connections.

Connect to the CONTROL ]

S-IN on your VCR. I

' 1.[. vmc-_'os/82os

VIDEO (yellow) _ VCR

RK-G69HG t

(not supplied)

(Rear of KV-35V65)

Connecting S-Link to a DBS

S-Link will automatically power on the TV

and switch to the correct video input when

you power on the DBS.

1 Using A/V connectors, connect AUDIO

and VIDEO OUT on your DBS to AUDIO

and VIDEO IN on your TV.

2 Using an S-Link connector (mono mini

plug), connect S-LINK on your DBS to

S-LINK on your TV.

The S-Link connector must be in the

same VIDEO-IN jacks as the A/V cables

on your TV.

DBS _eceivel

Antenna

Cable _ J_,--d,-_- AUDIO -R (red)

_ _-AUDIO-L (white) _l_--

t '_-wDEo (ye,owl__.=>_

(not supplied)[ JMC-810S/820S (not supplied}-

(Rear of KV-3SV65)

_H Basic Set Up

Inserting batteries

Insert two size AA (R6) batteries (supplied) by

matching the + and - on the batteries to the

diagram inside the battery compartment.

Notes

• Remove the batteries to avoid damage

from possible battery leakage whenever

you anticipate that the remote control will

not be used for an extended period.

• Handle the remote control with care.

Avoid dropping it, getting it wet, or

placing it in direct sunlight, near a heater,

or where the humidity is high.

• Your remote control can be programmed to

operate most video equipment. (see page 30)

Using the remote control

move & select buttons

The supplied remote control has "arrow"

buttons (4,, _, _., ._) which allow for

movement of the on-screen selector. Pressing

on the outer buttons will cause the selector to

move in the corresponding directon. Pressing

the center button ((_)) will select the item.

Adjustment bars

When menu items present an adjustment bar

( _ or _), use the arrow buttons to

change the setting.

On-screen help/instructions

Several menu windows will provide prompts

and instructions to assist you in navigating

through the different functions. When

presented, use these to supplement the instructions

in this manual.

Using Your New TV

Setting up the TV automatically

The Easy Setup Guide allows you to set the

on-screen language and set all receivable

channels in one step.

The Easy Setup Guide feature does not apply for

installations that use a cable boxfor all channel

selection.

To set up the TV manually, refer to "Using the

SET UP menu" on page 26.

Tips "_"

• Perfvrmthisfunctionduringth_day, withtheantenna

and/orcableproperlyconnected,toensurethatallavailable

channelswillbebroadcastingandreceivable.

• TheTVmustbesettotheTVinputtoexecuteAUTO

PROGRAM,PressTV/VIDEOuntilachannel

numberappears.

• If your cableorantenna is connected toAUX, press

ANT untilAUX appearsnexttothechannelnumber.

(KV-32S65, 32V65, 35S65,35V65 only)

Using the buttons on the front of the TV:

s_uPW;_lOeO -vogue. -CHaNNB.. _OWER

o 0 IZIZIIZEI-G

For KV-32V65, 35V65, the control buttons are

located on the top of the TV.

1 Press POWER to turn on the TV.

The Easy Setup Guide screen appears.

ENGLISH : [CH+]

POWER ESPANOL : I[CH-]]

FRAN_AIS : VOL+

AUTO SET UP: VOL-

DEMO : [W/VIDEO]

First please connect

Press ISETUPI to exit

cable/antenna.

2 Press CH + to select ENGLISH screens,

CH - to select ESPANOL screens

or VOL + to select FRAN_AIS screens.

-CHANNEL+

3 Press VOL - to continue or TV/VIDEO for

a DEMO of functions and menus.

-- VOLUME +

AUTO PROGRAM

AUTO PROGRAM appears and the TV

starts scanning and presetting channels

automatically. If the TV receives cable TV

channels, CABLE is set ON automatically.

To perform AUTO SET UP again

Press the SET UP button on the TV and follow

steps 2-3.

Notes

• When you perform AUTO PROGRAM,

your CHANNEL FIX, CHANNEL BLOCK,

and ON/OFF TIMER settings will be

erased.

To reset your TV to factory settings, turn

the TV on. Then, while pressing the RESET

button on your remote control, press the

POWER key on your TV. The TV will turn

itself off, then back on.

Watching the TV _._ REFERTOTHE

ILLUSTRATION OF THE

All of the TV features can be accessed via the remote REMOTE CONTROL ON THE

control. The following chart will explain the function INSIDE FRONT COVER OF

of the buttons found on your remote control. THIS MANUAL AS YOU

REVIEW THIS CHART

_WER

_ovo o_/_ Press when you want to turn equipment on and off.

CZ)

-- FU,,_T,O,-- Press when you want to control connected components with your remote

'_(_ C_) control. (see pages 30-32 for instructions on programming your remote control)

(_). (_ Use for direct channel selection. Press 0-9 to select a channel, the channel will

change after 2 seconds, or you can press ENTER for immediate selection.

Press to scan through the channels.

Keeping the CH + or- pressed allows you to rapidly scan to the desired channel,

JouP Press to alternate or jump back and forth between two channels. You can jump

(_) between the last two channels selected with the 0-9 keys.

MUTING

O Press to mute the sound (MUTING will appear on the screen). Press again or

press VOL + to restore sound.

SLEEP Press repeatedly until the TV displays the approximate time in minutes (30, 60, or

90) that you want the TV to remain on before shutting off automatically. Cancel by

pressing until SLEEP OFF appears.

Using Your New. i V (co ,,t nued)

Press repeatedly to cycle through available displays:

Status

o,sPu_y Channel number, current time, channel caption (if set) are displayed.

CAPTION VISION

Closed Captioning will be displayed if the broadcaster offers this service.

(see right)

To cancel the display, press DISPLAY until DISPLAY OFF appears.

Press repeatedly to cycle through available video inputs:

w_woEo TM and VIDEO 1 (KV-32S40 only)

"rv, VIDEO 1 and VIDEO 2 (KV-32S45, 32S65, 35S40, 35S45, 35S65 only)

TV, VIDEO 1, VIDEO 2 and VIDEO 3 (KV-32V40, 32V65, 35V65 only)

Press to change the VHF/UHF input to the AUX input. (KV-32S65, 32V65, 35S65,

A_ 35V65 only)

(_ Press to change to the TV input. (KV-32S40, 32S45, 32V40, 35S40, 35S45 only)

(AUX tnpdt) For detailed connection information, see "Cable and antenna" or "Cable box and

cable" on pages 5-6.

WNrR Press when you are finished using a VCR and you want to switch to the "IV input.

+O Your VCR power will remain on.

.TS Press this button to cycle through the Multi-channel TV Sound (MTS) options:

O STEREO, SAP, MONO. (see page 24)

GUIDE GUIDE is a feature of DBS, refer to your DBS operation instructions.

SYSTEM The SYSTEM OFF button allows you to power off all Sony equipment at once.

O_F

(_ (KV-32S45, 32S65, 32V65, 35S45, 35S65, 35V65 only)

Press to turn ON or OFF one of the following audio effects:

(_) SURROUND: KV-32S40, 32S45, 32S65, 35S40, 35S45, 35S65 only

AUTO VOLUME: KV-32V40, 32V65, 35V65 only

w c_s See page 23 for more information on AUDIO settings.

TV/DBS is a feature of DBS, refer to your DBS operating instructions.

CAPTION VISION

fCIosed Caption)

SET UP 1

CHANNEL SET UP

CHANNEL BLOCK

FAVORITE CHANNEL

VIDEO LABEL

_CAPTION VISION:

LANGUAGE: ENGLISH

TILT CORRECTtON: 0

_MENU

Select _ Exlt

CAPTION VISION can be used for programs

that are broadcast with closed caption.

CC1, 2, 3 or 4

Shows you a printed version of the dialog or

sound effects of a program. (The mode should

be set to CC1 for most programs)

TEXT1, 2, 3 or 4

Shows you network/station information

presented using either half or the whole screen.

XDS (Extended Data Service)

Shows a network name, program name,

program length, and time of the show ifthe

broadcaster offers this service.

Note

• Poor reception of TV programs can cause

errors in CAPTION VISION and XDS.

Captions may appear with a white box or

other errors instead of intended text.

Watching two programs at

one time - PIP

The Picture-in-Picture (PIP) feature allows

you to view two channels simultaneously, one

in the full size "main" picture and one in a

smaller "window" picture.

Single Tuner PIP

• KV-32$45,35545only

If you have model KV-32S65, 32V65, 35S65 or

35V65, see page 19.

These models are equipped with a single

tuner. This simply means that a VCR must be

connected and turned on for PIP to operate.

t il,_ _

To ensure a correct single tuner PIP connection

make sure the following list is complete before using PIP:

• AcableorantennaisconnectedtotheVCR

• The VCR is connected to your TV (see pages 5-7)

• The VCR is turned on

• The remote control has been programmed to operate

the VCR (see page 30)

Note

• You must press TV (FUNCTION) before

you can control PIP with the yellow

labeled buttons.

--"_t'" REFER TO THE ILLUSTRATION OF

L.._: j THE REMOTE CONTROL ON THE

INSIDE FRONT COVER OF THIS

MANUAL AS YOU REWEW THIS

CHART

TEe seul_J of the main Main picture

p_cture is _eceived through

the TV

";: picture

• ::r ' received through

the second tuner

picture

PIP Press once to display the window picture (1/9 size).

_) Press again to reduce the size of the window picture (1/16 size).

Press a third time to remove the window picture.

TVNIDEO Press repeatedly to cycle through available video inputs inthe window:

_) TV, VIDEO 1, VIDEO 2

TVNIDEO Press repeatedly to cycle through available video inputs in the

main picture:

"IV, VIDEO 1, VIDEO 2

AUDIO Press to alternate sound between the main picture and the window

(_) A _ will for a few seconds to indicate which picture ispicture. appear

receiving sound.

Using Your New TV (continued)

_^ • •

CH Press to change the channel• You must press VTR/DVD (FUNCTION), then

use the main CH +/- buttons to change channels in the window picture. (see right)

POSITION Press to move the location of the window picture (counterclockwise) around the

(_ main picture.

FREEZE Press to freeze the window picture. Great for copying down phone numbers,

(_ addresses, recipes, etc.

Press FREEZE again to restore the picture.

SWAP Press to switch the audio and video of the main picture and the window picture.

(_ Each time you press SWAP, the picture and sound of the two will be swapped.

CHANGING CHANNELS

1 PressTVNIDEO untilyou reach the TV input•

2 PressPIP (the windowpicture appears)•

To change the window picture: GH

1 Press VTR/DVD (FUNCTION). {(-I-_

2 Press the main CH +/- buttons f_,,,_

to change channels. (,_

To change the main picture:

1 Press TV (FUNCTION).

2 Press the main CH +/- buttons to change

channels.

Notes

• If you have the same program in both the

window and the main picture and cannot

change the channel in the window; press

TVNIDEO until you reach the TV input in

the main picture.

• Your remote control must be programmed

to operate the VCR. (see page 30)

Page is loading ...

Sony KV-35S45 Owner's manual

Brand: Sony

Model: KV-35S45

Category: LCD TVs

Type: Owner's manual

Download PDF

report

Sony KV-35S45 Owner's manual

Sony KV-35S45 Owner's manual

Related papers

Other documents