Freedom 73014058
The Freedom 73014058 is a versatile device that can be used for a variety of purposes. With its ability to measure distances, calculate areas, and determine angles, it is a valuable tool for anyone who needs to make precise measurements.
Some of the key features of the Freedom 73014058 include:
- Distance measurement: The Freedom 73014058 can measure distances up to 100 meters with an accuracy of ±2 mm. This makes it ideal for measuring the length of rooms, walls, and other objects.
- Area calculation: The Freedom 73014058 can calculate the area of any surface, making it a useful tool for landscapers, architects, and other professionals who need to determine the size of an area.
Freedom 73014058
The Freedom 73014058 is a versatile device that can be used for a variety of purposes. With its ability to measure distances, calculate areas, and determine angles, it is a valuable tool for anyone who needs to make precise measurements.
Some of the key features of the Freedom 73014058 include:
- Distance measurement: The Freedom 73014058 can measure distances up to 100 meters with an accuracy of ±2 mm. This makes it ideal for measuring the length of rooms, walls, and other objects.
- Area calculation: The Freedom 73014058 can calculate the area of any surface, making it a useful tool for landscapers, architects, and other professionals who need to determine the size of an area.
Staking Your Fence Line
Pre-determine the location of your fence line as illustrated
Locate corner, line, and end/gate posts. Determine all gate locations
Locating Posts
Measure the width of the fence panel (X) plus ½" for brackets, add
the width of the post (Y). This is the general on center measurement
for post hole location. It is highly recommended to dig enough holes
to install 3-4 sections of fence at a time to ensure proper post hole
placement.
To square up corners of the fence
line use the 3-4-5 right triangle
method (measure 3' and 4' from
the corner and the diagonal from
those points should be 5')
Rail Bracket Location
For correct bracket placement, measure down 2" from the top of the post, and make a mark.
Then, measure from the top of the panel to the top of the first horizontal rail. Mark this
measurement on the post for the first bracket placement.
Next measure the distance from the top of the top rail to the top of the next rail. This is the
measurement for placement of the next bracket. Repeat for any additional rails.
Offset Bracket Options:
On 1-3/8" pickets we recommend you offset the rail brackets. This will allow the panel to set
inside the posts and not stick out. See top view diagram.
Installing Panel
A) Set panel into the brackets on the first pre-set post (Figure 3)
B) Place the next post (with brackets) in the hole on the opposite
end of the panel without any concrete in the hole
C) Ensure posts are against panel and secure all screws into the
panel in the center
of the bracket slots
D) Level and plumb post
E) Horizontally level panel
F) Add concrete according to manufacturers instructions
G) Continue installing all other panels using above instructions
The finished look shows the post top 2" above the fence panel.
(Figure D)
Post
Rail Bracket
1-3/8" Pickets
Post
Rail Bracket
Privacy Panels
Post
Rail Bracket
Pry last board up slightly to
wedge bracket into rail
Dogear Boards
Use all screw holes
12"
24"
Frost
Line
6"
*Installation if Frost Line exceeds 30"
Standard Post Installation
a) Dig post hole 12" in diameter 30" deep
b) Add 6" of gravel for post drainage
c) Insert post in center of post hole
d) Level and plumb post
e) Fill remainder of first hole with concrete
according to manufacturers instructions
f) Recheck level and plumb Always allow
approximately 2" of ground clearance under
panel
– Add concrete to next post hole
after panel is installed
– *If frost line exceeds 30" (Figure A)
Dig hole to the appropriate depth
Add 6" of gravel for post drainage
Add concrete until a depth of 24"
remains
– Follow above instructions from step (c)
Pre-Built Vinyl Fence Installation Instructions
-
1
Freedom 73014058
The Freedom 73014058 is a versatile device that can be used for a variety of purposes. With its ability to measure distances, calculate areas, and determine angles, it is a valuable tool for anyone who needs to make precise measurements.
Some of the key features of the Freedom 73014058 include:
- Distance measurement: The Freedom 73014058 can measure distances up to 100 meters with an accuracy of ±2 mm. This makes it ideal for measuring the length of rooms, walls, and other objects.
- Area calculation: The Freedom 73014058 can calculate the area of any surface, making it a useful tool for landscapers, architects, and other professionals who need to determine the size of an area.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Unbranded 549000102040800 Installation guide
-
-
Signature Development 810901500000000 Operating instructions
-
Fortress Building Products 713580541 Installation guide
-
Veranda FNS POST SB J Installation guide
-
Trex Fencing TFBPFK68H-P5 Installation guide
-
Ply Gem 8811355HD Installation guide
-
Barrette Outdoor Living 73014450 Installation guide
-
Trex WBPCC050509 Installation guide
-
Barrette Outdoor Living 73014378 Installation guide
