Vari-Lite RDM SPLITTER 6 Quick start guide

Vari-Lite
Brand
Vari-Lite
Model
RDM SPLITTER 6
Category
Stroboscopes & disco lights
Type
Quick start guide

Vari-Lite RDM SPLITTER 6 is an RDM/DMX signal amplifier, dedicated for use to distribute RDM/DMX signals. The input signal is divided into 6 outputs with each output interface electrically isolated from the input. It can effectively buffer, amplify and divide DMX/RDM signals, with opto isolation. The device features a power indicator, DMX input and output connectors on both the front and rear panels, and DMX present indicators. It has a power consumption of 5W, dimensions of 482 x 155 x 44mm (1.58 x 0.51 x 0.14 in), and a weight of 2.2kg (4.85 lb).

Vari-Lite RDM SPLITTER 6 is an RDM/DMX signal amplifier, dedicated for use to distribute RDM/DMX signals. The input signal is divided into 6 outputs with each output interface electrically isolated from the input. It can effectively buffer, amplify and divide DMX/RDM signals, with opto isolation. The device features a power indicator, DMX input and output connectors on both the front and rear panels, and DMX present indicators. It has a power consumption of 5W, dimensions of 482 x 155 x 44mm (1.58 x 0.51 x 0.14 in), and a weight of 2.2kg (4.85 lb).

2-450400-010 1
RDM SPLITTER
QUICK START GUIDE
INSTALLATION AND SET UP
FRONT PANEL CONNECTIONS
REAR PANEL CONNECTIONS
TECHNICAL SPECIFICATIONS
Power in: 100~240VAC at 50/60Hz
Power consumption: 5W
Dimensions 482 x 155 x 44mm (1.58 x 0.51 x 0.14 in)
Weight: 2.2kg (4.85 lb)
OVERVIEW
The Strand RD Splitter is an RDM/DMX signal amplifi er, dedicated for use to distribute RDM/DMX signals. The
input signal is divided into 6 outputs with each output interface electrically isolated from the input
• Receiving standard DMX-512 signal /RDM signal
• It can e ectively bu er, amplify and divide DMX/RDM signals.
• Signal input connectors front and rear
• Signal through output connectors front and rear.
• 6 independent electrical isolation signal distribution output using 5-pin XLR
• Input is electrically isolated from output and output to withstand voltage:> 1000V
This document provides installation and operation instructions for the following product(s):
PRODUCT NAME ORDER CODE
RDM splitter 65026
1 2 3
5
4
Power indicator
DMX input - male 5-pin XLR input for DMX/RDM signal
DMX output - female 5-pin XLR output for unbuered DMX thru signal
DMX outputs - Female 5-pin XLR outputs for DMX/RDM signal, with opto isolation
DMX present indicators
1
2
3
5
4
6 7
8
9 10
Power input connector - powerCON power input
Fuse - T 1A
Power switch
DMX input - male 5-pin XLR input for DMX/RDM signal (paralleled with front panel)
DMX output - female 5-pin XLR output for unbuered DMX thru signal (paralleled with front panel)
6
7
8
10
9
Model:
Serial NO:
Power:
Fuse:
RDM Splitter
AE-02190001
AC 100-240V,50/60Hz /5.3W
T1A/250V
Manufacturing Date:February 2019
Made in China
RDM SPLITTER
IMPORTANT INFORMATION
WARNINGS AND NOTICES
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
• For indoor, dry locations use only. Do not use outdoors.
• Do not mount near gas or electric heaters.
• Equipment should be mounted in locations and at heights where it will not readily be subjected to tamper-
ing by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• Not for residential use. Do not use this equipment for other than intended use.
• Refer service to qualifi ed personnel.
SAVE THESE INSTRUCTIONS.
WARNING: You must have access to a main circuit breaker or other power disconnect device before installing
any wiring. Be sure that power is disconnected by removing fuses or turning the main circuit breaker o before
installation. Installing the device with power on may expose you to dangerous voltages and damage the device. A
qualifi ed electrician must perform this installation.
WARNING: Refer to National Electrical Code® and local codes for cable specifi cations. Failure to use proper
cable can result in damage to equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the National Electric Code® and local
regulations. It is also intended for installation in indoor applications only. Before any electrical work is performed,
disconnect power at the circuit breaker or remove the fuse to avoid shock or damage to the control. It is recom-
mended that a qualifi ed electrician perform this installation.
2-450400-010 2
2000851
CUSTOMER SERVICE
If you have any questions regarding this product, please contact Customer Service at +1-214-647-7880 or via
e-mail at entertainment.service@signify.
LIMITED 2-YEAR WARRANTY
Strand o ers a two-year limited warranty on its control products against defects in materials or workmanship
from the date of delivery. A copy of Strand two-year limited warranty containing specifi c terms and conditions
can be obtained from the Strand web site at www.vari-lite.com or by contacting your local Strand offi ce.
©2023 Signify Holding. All rights reserved.
All trademarks are owned by Signify Holding or their respective owners. The information provided herein is
subject to change, without notice. Signify does not give any representation or warranty as to the accuracy
or completeness of the information included herein and shall not be liable for any action in reliance
thereon. The information presented in this document is not intended as any commercial offer and does not
form part of any quotation or contract, unless otherwise agreed by Signify. Data subject to change.
WWW.VARI-LITE.COM
QUICK START GUIDE
  • Page 1 1
  • Page 2 2

Vari-Lite RDM SPLITTER 6 Quick start guide

Vari-Lite
Brand
Vari-Lite
Model
RDM SPLITTER 6
Category
Stroboscopes & disco lights
Type
Quick start guide

Vari-Lite RDM SPLITTER 6 is an RDM/DMX signal amplifier, dedicated for use to distribute RDM/DMX signals. The input signal is divided into 6 outputs with each output interface electrically isolated from the input. It can effectively buffer, amplify and divide DMX/RDM signals, with opto isolation. The device features a power indicator, DMX input and output connectors on both the front and rear panels, and DMX present indicators. It has a power consumption of 5W, dimensions of 482 x 155 x 44mm (1.58 x 0.51 x 0.14 in), and a weight of 2.2kg (4.85 lb).

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents