Task Lighting LP24HR12NDGSN40 Installation guide

Brand: Task Lighting

Model: LP24HR12NDGSN40

Type: Installation guide

Task Lighting LP24HR12NDGSN40

The Task Lighting LP24HR12NDGSN40 is a lighted power strip with a built-in power supply that can be used to power and illuminate a variety of devices. It features a sleek design with a brushed nickel finish and a lighted valance that provides ambient light. The power strip has 12 outlets, including 4 USB ports, and a 15-foot cord, making it ideal for use in a variety of applications, such as:

In the kitchen, to power and illuminate small appliances and gadgets
In the office, to power and illuminate computers, monitors, and other office equipment
In the bedroom, to power and illuminate bedside lamps, alarm clocks, and other devices

Task Lighting LP24HR12NDGSN40

In the kitchen, to power and illuminate small appliances and gadgets
In the office, to power and illuminate computers, monitors, and other office equipment
In the bedroom, to power and illuminate bedside lamps, alarm clocks, and other devices

www.TaskLighting.com

DesignAndSupport@TaskLighting.com

Customer Service: 800-445-6404

Design Services & Tech Support: 866-848-9094

LIGHTED POWER STRIP

installation instructions

January 2019

Customer Service: 800.445.6404 • Design Services/Technical Support: 866.848.9094 • TaskLighting.com

Lighted Power Strip DV Series

Installation Instructions for LPS WITH Built-In Power Supply

Turn power o at panel. Carefully pry open each

piece with tool (provided). Insert Romex connector into

knockout hole inside of back frame. Pull wires into LPS.

Tool

WTWT

GRN

BKBK

120V

DIVIDER PLATE

SWITCH

DRIVER

RED +

BLUE -

WT GRN

GRN

General Guidelines

• Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at LPS.

• All wiring must meet NEC® and local codes.

• Light valance recommended.

• Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed.

WTWT

GRN

BKBK

120V

DIVIDER PLATE

SWITCH

DRIVER

RED +

BLUE -

WT GRN

GRN

Factory

Wired

Factory

Wired

Secure LPS to wall by screwing into wall studs or

use anchors provided. Connect BLACK Romex

wire to BLACK wire from receptacles and switch.

Connect WHITE Romex wire to WHITE wire from

receptacles and driver. Ground all GREEN wires to

PEM studs inside of back frame.

Wiring for Combined Light and Receptacle Circuit - Non Dimmable

To terminate last LPS, use wire nuts on ends

of wires.

When connecting 2 or more LPS xtures, run

Romex from xture to xture. Ground each

section to the next.

Snap cover in place and turn power on.

Secure LPS to wall by screwing into wall studs or

use anchors provided. If running two circuits, one

for receptacles, one for lighting, connect xture

wires to appropriate Romex wires. BLACK to

BLACK. WHITE to WHITE. Ground all GREEN wires

to PEM studs inside of back frame.

Wiring for Separate Light and Receptacle Circuits

Bottom of Cabinet

Step 1 Step 2

Step 3

Step 4

To terminate last LPS, use wire nuts on ends

of wires.

When connecting 2 or more LPS xtures, run

Romex from xture to xture. Ground each

section to the next.

Snap cover in place and turn power on.

Step 2

Step 3

Step 4

Step 1

12-1/2” Fixture Shown

120V for

receptacles

120V

for lights

Customer Service: 800.445.6404 • Design Services/Technical Support: 866.848.9094 • TaskLighting.com

120V Receptacle

Circuit. Must be

GFCI Protected.

(non dimmable)

Lighting Circuit

Back Frame

Positive (+)

Negative (-)

Wiring Diagram for Separate Light & Receptacle Circuits

Back Frame

Cover

Positive (+)

Negative (-)

Wiring Diagram for Combined Light & Receptacle Circuit - Non Dimmable

Cover

18-1/2” Fixture Shown

Divider Plate

DRIVER

120V Receptacle

Circuit. Must be

GFCI Protected.

Lighted Power Strip DV Series

Wiring Diagram for 18-1/2" LPS WITH Built-In Power Supply

Customer Service: 800.445.6404 • Design Services/Technical Support: 866.848.9094 • TaskLighting.com

Lighted Power Strip RM Series

Installation Instructions for LPS WITHOUT Built-In Power Supply

Using appropriate knockout hole, pull low voltage

wire from remote power supply into the low voltage

space, connect BLACK wire (negative) to BLACK

wire from lights and RED wire (positive) to RED wire.

Snap cover in place and turn power on.

Turn power o at panel. Carefully pry open

each piece with tool (provided). Insert

Romex connector into knockout hole

inside of back frame. Pull wires into LPS.

General Guidelines

• Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at LPS.

• All wiring must meet NEC® and local codes.

• Light valance recommended.

• Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed.

Secure LPS to wall by screwing into wall studs or

use anchors provided. Connect BLACK to BLACK,

WHITE to WHITE. Ground all GREEN wires to PEM

studs inside of back frame.

Bottom of Cabinet

Remote Power Supply- 120V Entry

12-1/2” Fixture Shown

GRN

120V

DIVIDER PLATE

LOW VOLTAGE

RED +

BLACK -

When connecting two LPS, run Romex from xture

to xture. Ground each section to the next.

Remote Power Supply-Low Voltage Entry

To terminate last LPS, use wire nuts on ends of wires.

Tool

18-1/2” Fixture Shown

Step 2

Step 3

Step 4

Step 1

Step 5

15vDC wire

120V Circuit

Positive (+)

Negative (-)

Back Frame

Cover

Divider Plate

Task Lighting LP24HR12NDGSN40 Installation guide

Brand: Task Lighting

Model: LP24HR12NDGSN40

Type: Installation guide

Task Lighting LP24HR12NDGSN40

In the kitchen, to power and illuminate small appliances and gadgets
In the office, to power and illuminate computers, monitors, and other office equipment
In the bedroom, to power and illuminate bedside lamps, alarm clocks, and other devices

Download PDF

report

Task Lighting LP24HR12NDGSN40 Installation guide

Task Lighting LP24HR12NDGSN40 Installation guide

Other documents