Fortress Technologies FGS2014 User manual

1

Steam Brush

User Manual

Model No.: FGS2014

*Before operating the unit, please read this manual thoroughly and retain it for future reference.

2

CONTENT

PAGE

SAFETY INSTRUCTION

3

PARTS DESCRIPTION

5

OPERATION INSTRUCTION

6

MAINTENANCE INSTRUCTION

9

TROUBLE SHOOTING

9

SPECIFICATION

9

WARRANTY

10

3

SAFETY INSTRUCTION

1. To avoid electric shock, risk of fire or injury, please read the user manual carefully before

using the appliance and keep it for future reference.

2. This appliance is for household use only. Please use suitable power source (110-120 / 220-

240V~ 50/60Hz).

3. Never immerse the appliance in water or other liquids.

4. Do not use the appliance under direct sunshine.

5. Please turn off the appliance when not in use otherwise it may result in danger.

6. The appliance must not be left unattended while it is connected to the supply mains.

7. Keep the appliance away from children.

8. This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance in a safe way

and understand the hazards involved.

9. Children should be supervised to ensure that they do not play with the appliance.

10. With any indication of malfunction, please stop using the appliance immediately to avoid

hazard. Take it to / Contact the authorized service center for repair. Do not attempt to repair

or change any parts by yourself.

11. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualified persons in order to avoid hazard.

12. Please turn off and unplug the appliance during filling, before cleaning or maintenance.

13. Clean the surface of the appliance with dry cloth. Do not use corrosive detergent or solvent

to clean. Do not swash the appliance with water.

14. Please turn off and unplug the appliance when not in use , make sure the power is off

before pulling out the plug and do not pull the cord.

15. When the appliance is not in use for a prolonged period, please turn it off, unplug it, pack it

well, and store it in dry cool place.

16. Forbid to put flammable and explosive objects around the appliance, and do not use the

appliance in an environment full of flammable gas and powder. Keep away from any fire and

heat sources.

17. The appliance generates high temperature steam. Always handle with care and warn other

users of the potential dangers.

18. Unwind and straighten the power cord before use.

19. The iron must be used and rested on a flat and stable surface.

20. Avoid power cord touches the soleplate.

21. The plug must be removed from the socket before the water reservoir is filled with water.

22. Empty the water tank after use.

23. Do not add perfume, vinegar or other chemical liquids into the water tank; they can damage

the appliance seriously.

24. Do not use the appliance when it is damaged or performs abnormally.

25. Do not use this iron if it has been dropped with visible signs of damage or leakage problem.

26. Do not touch the soleplate during rest or right after use to avoid injury by heat.

27. Do not roll the power cord round the appliance or base for storage until it cool down

completely.

28. Check the mains voltage: Use a coin or suitable object to turn the mains voltage switch to

local mains voltage.

29. For using in Hong Kong and Macau: Please ensure to turn the main voltage switch to “220V

240V” position before each use.

4

30. Disconnect the appliance from the mains supply and allow it to cool down before:

 Remove / reattach the water tank.

 Remove / reattach the brush attachment.

31. Do not connect the appliance to a wall socket intended for shavers.

32. Do not allow children touch the appliance or the power cord when ironing.

33. Do not use an extension power cord.

34. When the appliance is used or connected to the mains, do not place the iron such that the

soleplate touches with any surface. Lay it down on its side on a solid flat surface.

35. Do not attempt to open the cabinets or dismantle any parts from the iron in order not to

damage the unit.

36. Do not allow children to perform cleaning and user maintenance when they are without

supervision.

37. Care should be taken when using the appliance due to the emission of steam.

38. When placing the iron on its stand, ensure that the surface on the stand is placed is stable.

39. Do not touch the surfaces marked with symbol during operation or rest to avoid injury

by heat. (Please refer to the following Figure 1 and Figure 2)

CAUTION:Hot Surface!

Figure 1: Left Side-Hot Surface

CAUTION:Hot Surface!

Figure 2: Right Side-Hot Surface

5

PARTS DESCRIPTION

A. Brush Attachment B. Non-stick Soleplate

C. Temperature Dial D. Pilot Light

E. Burst of Steam Button F. Detachable Water Tank

G. Power Cord Guard H. Mains Voltage Switch

I. Brush Lock J. Fluff Pad

K. Fabric Brush

6

OPERATION INSTRUCTION

Notes:

1. Sort out the articles to be ironed according to the type of fabric. This will minimize the

frequency of temperature adjustment for different garments.

2. Test ironing a small area on the backside or inside the garment if you are unsure about the

type of fabric. Start with low temperature and increase gradually.

3. Delicate fabrics such as silk, wool, velour and, etc, are suggested to be ironed with an ironing

cloth to prevent shine marks.

4. To iron without an ironing board, you can spread a towel on a firm flat surface. Please ensure

that the surface is heat and moisture resistance. Do not use glass or plastic.

5. Read the garment labels and follow the manufacturer’s ironing instructions that are often

shown by symbols similar as follows:

Voltage Switch

 The appliance is a dual-voltage design and it can be used in 110-120V or 220-240V.

 Please ensure the local power supply voltage is the same as the rating marked on the voltage

switch of the appliance.

 For using in Hong Kong and Macau: Please ensure to turn the main voltage switch to “220V

240V” position before each use.

How to Fill Water

Note: Please unplug the appliance from the mains supply and allow it to cool down completely.

1. Hold the handle of bottom part and pull out the Water Tank. (Fig. 1)

2. Release the water inlet cover, and fill up with water. (Fig. 2)

3. Replace the water inlet cover.

4. Clean the spilt water with a dry cloth.

5. Reattach the Water Tank by sliding on the handle of the appliance until it locks in place firmly. (Fig. 3)

(1) (2) (3)

7

First Time Use

1. Remove any protective films or stickers from the soleplate and the appliance body.

2. Unwind and straighten the power cord.

3. Fill the Water Tank (See How to Fill Water).

4. Connect the appliance to a suitable mains supply outlet.

5. Turn the Temperature Dial to “ ” (3-dot) setting.

6. Pilot Light will go off when the desired temperature is reached.

7. It is suggested to begin first time ironing with an old towel as testing.

8. Press the Burst of Steam button until the water tank is empty and there is no more steam can

be produced, it means the preparation work is completed and the appliance is ready for

proper use.

Important – When using the appliance or while it is heating up, do not put it down on its

soleplate. Lay it down on its side on a solid and flat surface.

Dry Ironing

1. Connect the appliance to a suitable mains supply outlet.

2. Turn the Temperature Dial in clockwise direction; select “ ” (1-dot), “ ” (2-dot) or

“ ” (3-dot) according to the recommendation of the garment label.

3. Pilot Light will go off when the desired temperature is reached.

4. The appliance is ready for use.

5. After used, turn the Temperature Dial in anti-clockwise direction to the ‘MIN’ position to turn

off the appliance.

6. Disconnect the appliance from the mains supply outlet and lay it down on its side on a solid

and flat surface.

7. When the appliance gets cool completely, empty the water tank and store it in a safe place.

Burst of Steam Ironing / Vertical Steam

Note: Please unplug the appliance from the mains supply and allow it to cool down completely.

1. Fill the Water Tank (See How to Fill Water).

2. Connect the appliance to a suitable mains supply.

3. Turn the Temperature Dial to “ ” (3-dot) setting.

4. The Pilot Light will go off when the desired temperature is reached.

5. The iron is ready for use.

6. While ironing / vertical steam, press the Burst of Steam Button to release steam. It helps to

remove creases on the garment.

7. Do not press the Burst of Steam Button more than three times successively. Allow few

seconds intervals between operating the burst of steam, otherwise water leakage may occur.

8. After used, turn the Temperature Dial in anti-clockwise direction to the ‘MIN’ position to turn

off the appliance.

9. Disconnect the appliance from the mains supply outlet and lay it down on its side on a flat

and stable surface.

10. When the appliance gets cool completely, empty the water tank and store it in a safe place.

Warning- Do not apply steam on any clothes or fabrics that are being worn by human or pets.

Temperature of the steam is high.

8

Using Brush Attachment

Note: Please unplug the appliance from the mains supply and allow it to cool down completely.

Assembling the Brush Attachment

 Grip the Brush Attachment on the sides and slide it onto the soleplate completely. (Fig. 4)

 Turn the lock 180 degrees anti-clockwise to lock firmly with the appliance. (Fig.5)

Disassembling the Brush Attachment

1. Unlock by turning the knob 180 degrees clockwise. (Fig. 6)

2. Grip the Brush Attachment on the sides and slide it out from the soleplate completely. (Fig. 7)

(4) (5)

(6) (7)

Remarks:

1. The Fabric Brush is designed for use on curtains, sofa, and etc.

2. The Fluff Pad is designed for use on clothes, ties, and etc.

3. Threads, fluff, and hair can be easily removed with red fluff pad by brushing smoothly over

the garment from left to right.

4. To clean the Fluff Pad, slightly rub over with a towel.

9

MAINTENANCE INSTRUCTION

Cleaning

Your appliance has been designed to be used with tap water. If you live in an area with very hard

water, fast scale build-up will occur. Therefore it is recommended to fill the water tank with 50%

distilled water and 50% tap water to prolong the lifetime of your appliance. Do not use distilled

water only, as it is slightly acidic and may cause damage to your appliance. Do not put perfume,

vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank, as your

appliance is not designed to work with these chemicals.

Note: Please unplug the appliance from the mains supply and allow it to cool down completely.

1. Use a dry cloth or a non-scratching cleaner to remove any deposits on the soleplate or the

appliance body.

2. Never use sharp or rough objects to remove deposits on the soleplate.

TROUBLE SHOOTING

If the iron does not perform normally, please check the following points.

Problem

Possible Cause

Solution

The iron is plugged in but

the soleplate is cold.

The socket does not work.

Plug into another socket.

There is a connection

problem.

Check if the plug is connected to the

wall socket properly.

The temperature has been

set to the 'MIN' position.

Turn the Temperature Dial to the

desired temperature.

No steam comes out.

There may not be enough

water in the water tank.

Fill the water tank, see “HOW TO FILL

THE WATER”.

The Burst of Steam

function does not work.

There may not be enough

water in the water tank.

Fill the water tank, see “HOW TO FILL

THE WATER”.

First time usage.

Press the Burst of Steam Button few

times until the steam burst comes out.

The temp of the soleplate

is not high enough.

Incorrect temperature

setting.

Turn the Temperature Dial with

respect to the garment textile.

Water leakage from the

soleplate.

The iron's heat is not

enough to produce steam.

Set Temperature Dial to 3-dot

position.

Damage textile.

The iron is overheated.

Follow the garment guide or test on

the inside or the hem of the garment.

SPECIFICATION

Model No.

FGS2014

Product name

Steam Brush

Rated Voltage/Frequency

110-120 / 220-240V~ 50/60Hz

Power

840 – 1000W

Product Dimension (W x H x D)

315 x 85 x 70mm

10

WARRANTY

1. The product has 2 years warranty from the date of purchase.

2. The warranty shall not apply:

A. to any product subjected to misuse, alteration, act of God, improper handling, improper transport,

improper testing or unauthorized repair;

B. to cosmetic problems or defects which result from normal wear and tear under ordinary use yet

not affecting the performance or use of the product;

C. if the product is disassembled or altered;

D. to any packing, transportation, export / import tax or any related expenses.

3. CUSTOMER MUST PRESENT THE SALES INVOICE OR RECEIPT FOR 2 YEARS WARRANTY SERVICES.

4. Please bring along the product and sales invoice or receipt to our services center for warranty services

during office hour:

Address : Unit A, 20/F, Yip Shing Industrial Centre, No.19, Yip Shing Street,

Kwai Chung

Service Hotline : (852) 2428 1500

Service Hours:

Monday-Friday : 9:00am - 6:00pm

Saturday : 9:00am - 4:00pm

Sunday & Public Holiday : Closed

NOTES

 To prevent circuit overload and fire, no more than one safety compliant adaptor or extension unit

should be inserted into a socket outlet. (Do not connect other appliances to the socket outlet

supplying an electric heater.) No adaptor should be inserted into any extension unit or vice versa.

 Stop using an adaptor or an extension unit or a socket if its socket holes cannot firmly hold a plug if it

is too hard to insert a plug into it.

 This appliance must be plugged into a specific 220-240V socket. Please make sure the plug is fully

plugged-in before use. Do not use any adapter or extension cord; Never use the same supply socket

for this appliance and other appliances at the same time, in order to avoid damage to this appliance.

 THE APPLIANCE IS FOR HOUSEHOLD USE ONLY.

ENVIRONMENT

Do not throw away the appliance with the normal household waste at the end of its life, but

hand it in at an official collection point for recycling. By doing this, you help preserving the

environment.

IMPORTANT NOTICES

IN NO EVENT SHALL OUR COMPANY OR THE SUPPLIER BE LIABLE TO YOU OR ANY OTHER PARTY FOR ANY

DIRECT, INDIRECT, GENERAL SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR OTHER DAMAGES

ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT (INCLUDING, WITHOUT LIMITATION,

DAMAGES FOR INJURY, LOSS OF PROPERTY, BUSINESS PROFITS, BUSINESS INTERRUPTION) OR FROM ANY

BREACH OF WARRANTY, EVEN IF OUR COMPANY OR SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN NO CASE SHALL OUR COMPANY OR SUPPLIER’S LIABILITY EXCEED THE AMOUNT YOU

PAID FOR THE PRODUCT.

Specifications, designs and dimensions are subject to change without prior notice.

Fortress Technologies FGS2014 User manual

Fortress Technologies FGS2014 User manual

Related papers

Other documents