JB DV-29 Vacuum Gauge Blank-off Test Kit Operating instructions

Brand
JB
Model
DV-29 Vacuum Gauge Blank-off Test Kit
Type
Operating instructions

Below you will find brief information for DV-29, DV-22N, SH-35N. The DV-29 Vacuum Gauge Blank-off Test Kit creates a closed system for checking leaks with JB digital vacuum gauges DV-22N, DV-40S, DV-41 and SH-35N Wireless Digital Gauge. It features flexible metal hose and o-ring seal couplers for vacuum tight connections. It can test for pressure rise after pulling a vacuum and also can be used for subcooling method by reversing hook-up. The system is designed to be leak-proof. The kit includes several replacement parts like swivel coupler, male flare, valve assembly, metal hose and ball valve.

Below you will find brief information for DV-29, DV-22N, SH-35N. The DV-29 Vacuum Gauge Blank-off Test Kit creates a closed system for checking leaks with JB digital vacuum gauges DV-22N, DV-40S, DV-41 and SH-35N Wireless Digital Gauge. It features flexible metal hose and o-ring seal couplers for vacuum tight connections. It can test for pressure rise after pulling a vacuum and also can be used for subcooling method by reversing hook-up. The system is designed to be leak-proof. The kit includes several replacement parts like swivel coupler, male flare, valve assembly, metal hose and ball valve.

JB INDUSTRIES
800.323.0811 JBIND.COM [email protected]
DV-29
VACUUM GAUGE BLANK-OFF TEST KIT
The DV-29 Vacuum Gauge Blank-off Test Kit works
with JB digital vacuum gauges DV-22N, DV-40S,
DV-41 and the SH-35N Wireless Digital Gauge for
Superheat and Subcooling to create a closed system
ideal for checking leaks.
DV-29 INSTRUCTIONS
Valve position pictured for Pressure Rise Test. Valve “A” to vacuum
gauge is open and valves from manifold to “B” and “C” are closed.
Before making connection as pictured, close all ball valves before
hookup. NOTE: If vacuum gauge has 1/4” male flare, use DV-291 O-ring
Swivel Coupler included.
Leak-Proof Test Unit
Deep vacuum has its own unique properties which require vacuum tight
hoses. DV-29, with a flexible metal hose and o-ring seal couplers, is
absolutely vacuum tight. The o-ring coupler has a small rubber mass
that forms around irregularities in the flare fitting. When the flare is
screwed down, you get a metal seat and the o-ring lays around the flare
to give a positive seal.
Pulling a Vacuum
Open all valves and pull a vacuum. When the sensor reads between 300
and 400 microns and only if the compressor is in the vacuum, close
valves to the high and low sides of the system. This leaves the valve
closest to the micron gauge open. You now have the vacuum gauge
measuring the system to check for pressure rise. Wait for at least five to
a maximum of 20 minutes to allow system pressure to equalize.
The reading you see at the end of this test will be very close to what you
actually have in the system. A rapid rise during this test to atmospheric
pressure indicates a leak, while a slower rise to around 1500 microns
indicates moisture is present.
WARNING: While charging, close valve “A” connecting directly to the
vacuum gauge. Most vacuum gauges will not withstand high pressure.
PART NO. DESCRIPTION
DV-29 Leak-proof micron hook-up test kit, includes:
DV-292, DV-293, DV-294, and DV-295
DV-291 Replacement 1/4" SAE swivel coupler (D10244)
DV-292 Replacement 90° male flare with 1/4" o-ring QC
DV-293 Replacement valve assembly 1/4" MFL connector
DV-294 Replacement 10" (25.4 cm) metal hose with o-ring
DV-295 Replacement ball valve with o-ring QC and depressor
P90009 Replacement o-ring (10 pack)
DV-293
DV-294
DV-292
M2-5-410A
SOLD SEPARATELY
DV-22N
SOLD SEPARATELY
FOR SUPERHEAT
AND SUBCOOLING
SH-35N
SOLD SEPARATELY
DV-295
SUBCOOLING
To charge the system using the subcooling method, reverse the
hook-up described.
Close valve “A” during charging and remove the vacuum gauge and attach
a superheat gauge (SH-35N). Bleed at quick coupler before charging.
1020
  • Page 1 1

JB DV-29 Vacuum Gauge Blank-off Test Kit Operating instructions

Brand
JB
Model
DV-29 Vacuum Gauge Blank-off Test Kit
Type
Operating instructions

Below you will find brief information for DV-29, DV-22N, SH-35N. The DV-29 Vacuum Gauge Blank-off Test Kit creates a closed system for checking leaks with JB digital vacuum gauges DV-22N, DV-40S, DV-41 and SH-35N Wireless Digital Gauge. It features flexible metal hose and o-ring seal couplers for vacuum tight connections. It can test for pressure rise after pulling a vacuum and also can be used for subcooling method by reversing hook-up. The system is designed to be leak-proof. The kit includes several replacement parts like swivel coupler, male flare, valve assembly, metal hose and ball valve.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents