B.E.G. LUXOMAT PD3-1C-Micro Installation and Operating Instruction

Brand: B.E.G. LUXOMAT

Model: PD3-1C-Micro

Category: Motion detectors

Type: Installation and Operating Instruction

This manual is also suitable for

B.I.T.

Q.C.

PASSED

Installation and Operating Instruction for B.E.G. - Occupancy detectors PD3-1C-SM/-FC/-FM and PD3-2C-FC/-FM

2a.

Installation of the LUXO-

MAT

PD3-SM

2c.

Installation of the

LUXO-

MAT

PD3-FM

LUXOMAT

PD3-1C(-Micro)/-2C

2b.

Installation of the

LUXO-

MAT

PD3-FC

Sensor and power supply in one case

Power supply: 230V~ +6%/-10 %

Power consumption: < 1W

Ambient temperature: -25°C to +50°C

Degree of protection/class: SM IP54, FC and FM IP20,

FC with accessory IP23 / II

Settings: locally

Area of coverage: circular 360°

Range of coverage Ø H 2.50m / T = 18°C:

seated 2.50m / tangential 10m / radial 6 m

Recommended height for mounting: 2 - 3 m

Light measurement: mixed light, daylight + artificial light

Lux values - Potentiometer: 10 - 2000 Lux

• Channel 1 for light-connection

Type of contact: NOC/with pretravel tungsten contact

Contact load: 2000 W, 230V~, cos(ϕ) =1 /

1000 VA cos (ϕ) = 0.5

Time-settings: 30 sec. - 30 min. / Test

• Channel 2 for HVAC (only PD3-2C)

Contact load: 230 V~, 3 A cos (ϕ) =1

Time-settings: 5 min. - 120min. with time delay of 5 min.

for follow-up time > 15 min.

Dimensions H x Ø [mm] SM FC FM

PD3 52 x 106 84,5 x 80 65x 98

Visible portion when built into ceiling: 34 x 74mm

Declaration of Conformity: The product complies with

the low voltage recommendation 2006/95/EC and the

EMV recommendation 2004/108/EC.

Technical data

PD3

5. Trouble shooting

1. Lamp does not light up

Lamp may be defect:

Replace lamps

No mains connection/power:

Check connection and mains fuse by qualied electrician

Incorrect setting of CDS twilight threshold:

Correct setting of CDS threshold

Lens of sensor unit obstructed by dirt or other objects:

Clean lens, remove objects

2. Lamp turns ON too late or detection range too small

LUXOMAT

PD3 is mounted too high:

See table of mounting heights.

Correct mounting if required.

3. Lamp stays ON continuously

Continuous thermal activity detected ie fan, central heat-

ing ducts, animals within detection area:

Remove heatsource. Check proper function of LUXOMAT

PD3 by covering the fresnel-lens. After expiry of delay

timer, PD3 has to turn OFF lighting.

LUXOMAT

PD3 connected in parallel to a manual over-

ride switch:

Connect switch correctly

4. Unintended switching of light

Movement of heat source within detection area:

Check on presence of animals, fans or heaters

The detector can be installed

in conventional inlet-sockets

mounted on the ceiling.

The assembly plate enclosed

must be stripped off prior to

installation and secured to the

ceiling using 4 screws.

Having connected up the

cables in accordance with

regulations, the detector

can be placed in position

as shown in the drawing

opposite and, applying a little

pressure, can then be locked

into position with the assist-

ance of the spring clips.

The detector must be in-

stalled on a solid and level

surface. There is no need

for frames.

For mounting remove lens

Fasten the mounting base

to the ceiling.

Having connected up the wires in accordance

with regulations, secure the detector with 2

screws as per the illustration above.

1. Mounting preparations

Work on the 230 V mains supply

may only be carried out by qualified

professionals or by instructed persons

under the direction and supervision

of qualified skilled electrical person-

nel in accordance with electrotechni-

cal regulations.

Disconnect supply before installing!

The detector has

been designed

and developed

specifically for instal-

lation in suspended

ceilings.

A circular opening of

diameter 65mm must

be cut into ceiling.

Having connected up the cables in accor-

dance with regulations, the detector is

inserted into the opening as shown in the

drawing above and fixed into position with

the assistance of the spring clips.

e.g. 65 mm

Type SM FC FM

PD3-1C 92190 92196 92186

PD3-1C-Micro 92219 92184 –

PD3-2C – 92198 92188

Accessory:

BSK Ball basket guard 92199

FC-Covering IP23 92206

SM-Blinds 92260

7. Article / Part nr. / Accessory

6. Range of Coverage

quer zum Melder gehen

frontal zum Melder gehen

Unterkriechschutz

walking across

walking towards

seated

10 m

6 m

2.50 m

10 m

360°

2.50 m

3. Putting into operation / Settings

Follow-up time for device control (PD3-2C)

The time can be set infinitely variably at between

5 and 120 minutes.

Follow-up time for light control

The time can be set infinitely variably at between

30 seconds and 30 minutes.

Symbol

: impulse < 1sec.

Symbol

TEST: Test mode

(Every movement switches on the light for a period of

1 second, switching it off for a period of 2 seconds

after that regardless of the level of brightness.)

Twilight-switch for light control

The switch-on value for the light can be set at

between 10 and 2000Lux. Using the rotary control,

the luminance set points can be set as desired.

Symbol

: Night-time operation

Symbol

: Daytime/Night-time operation

Adjusting sensitivity (PD3-1C)

For sensitivity adjustment of the detector, both in the

interior and the exterior range, the PD3-1C-SM/-FC

is equipped with an additional knob (see pictures)

for excluding sources of interference, e.g. bad

weather conditions or draught air.

Max: for interior use

(recognition of the slightest movements)

Min: for exterior use

(exclusion of sources of interference)

Sound (PD3-1C-Micro)

Max: highest sensitivity

Min: microphone switched off

Intermediate values to be adjusted accordingly to

local conditions. Lighting of the LED means the noise-

detector is functioning and triggers the timer again.

The microphone is active for 9 seconds after the last

movement and time delay completed.

120

TEST

2000

1200

600

200

max.

min.

max.

min.

secs

mins

min

TEST

2000

1200

600

200

120

mins

~6 m

6 m 7 m

18m

6 m

~6 m

6 m

12 m

6 m

4 m

6 m

8. Wiring diagrams

MAN 5789 – 161209-4

9. PD3 - Connections

Connection PD3-1C-SM

NL L'

Connection

PD3-1C-FC/-FM

NL L'N

Connection

PD3-2C-FC/-FM

N LL'

–

10. PD3 - Dimensions

PD3-SM

PD3-FC

PD3-FM

11. Installation examples

Parallel-operation together with stairwell switch.

Alternatively switching by either motion detector or

stairwell switch.

L' N L

Parallel-operation with stairwell switch

Standby,

additionally manual switching is possible.

L' N L L' N L

Terminal connection voor parallel operation

L' N L

Switching with external switch PD3-1C-FC

L' N L

Permanent light operation with external switch

Standby

Switching is manually possible

(permanent light operation)

L' N L L' N L

Terminal connection for parallel-operation

Parallel switching

Max. 8 occupancy detectors keep settings (Lux and

time) the same.

L' N L

Standard operation with opt. arc extinctions kit

Arc

extinction kit

Standby

Optional extension for switching of parallel

inductors, rocker switches, uorescent lamps etc.

Terminal connection for parallel-operation PD3-2C-FC

dry

contact

Circuit like PD3-1C-FC, but additional with two dry

contact (relay 2).

R L' N L

645

R L' N L L NO NO

230VAC

50-60Hz

Slave /

Remote

84.5

R L' N L L NO NO

230VAC

50-60Hz

Slave /

Remote

48x4825 25

106

B.E.G. LUXOMAT PD3-1C-Micro Installation and Operating Instruction

Brand: B.E.G. LUXOMAT

Model: PD3-1C-Micro

Category: Motion detectors

Type: Installation and Operating Instruction

This manual is also suitable for

Download PDF

report

B.E.G. LUXOMAT PD3-1C-Micro Installation and Operating Instruction

This manual is also suitable for

B.E.G. LUXOMAT PD3-1C-Micro Installation and Operating Instruction

Related papers

Other documents