56192-Burford-bollard 20150813

Endon Lighting, LS9 0SE

Burford Bollard (IP44 Rated)

Safety Warnings

INSTRUCTION MANUAL

• ItisrecommendedthatthislightbeinstalledbyaqualiedelectricianinaccordancewithcurrentIEEWir-

ing Regulations and Building Regulations ( Part P ).

• This product is only suitable for connection to a 240v~50Hz supply and is for outdoor use.

• Runsupplywirefroma5-ampelectricalsupplyusingdoubleinsulated2or3-corecableoftypeH05RN-

age, a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for

useasaprotectiveconductor,orbeofinsulatedconcentricconstruction.Buriedcablesshallbemarked

bycablecoversorasuitablemarkingtape.Buriedconduitsandductsshallbesuitablyidentied.Buried

cables,conduitsandductsshallbeatasufcientdepthtoavoidbeingdamagedbyanyreasonablyfore-

seeable disturbance of the ground.

• Donotinstallabulbwithagreaterwattageordifferentshapethanspeciedonthelabel.

• Ifanymodicationismadeitwillinvalidatethewarrantyandmayrendertheproductunsafe.

• Iftheglassordiffuserisbrokenorcrackeditmustbereplaced,pleaseconsultyourretailer.Thisisthe

symbolwhichdenotesthisrequirement:

• Ifthereisa“MinimumDistance”Label,pleasedonotallowFlammableMaterialstorestwithinthatdis-

Followeachassemblystepinordertopreventincorrectassembly.

Ensure that the product is fully assembled as illustrated before use.

The Light pack contains:

Lighttting.

Terminalconnectionblock(s).

Fixingpack.

The following tools may be required:

Selectionofcrossandatheadscrewdrivers.

Electric drill and assorted drill bits.

Wirestrippers.

Electrical insulation tape.

Before you start

Care Information

Allow10minutestocoolbeforereplacing,adjustingorcleaning.

These assembly diagrams are intended as a guide – if in doubt consult a qualied electrician.

Assembly/ User Instructions Continued

Endon Lighting, LS9 0SE

1. Decideonthepositionofthelighttting/orremoveexistinglighttting.Takeanoteofthepositionofthe

covers or a suitable marking tape. Buried conduits and ducts shall be suitably identied. Buried cables,

conduitsandductsshallbeatasufcientdepthtoavoidbeingdamagedbyanyreasonablyforeseeable

disturbance of the ground.

4. Ifinstallingonexistingconcretebase,useholesinbaseasatemplatetodrillsuitablexingholes.Prepare

withsuitablegroundxingbolts(notsupplied).

5. Threadthecablethroughtheunit,screwingittogetherasyougo,asoutlinedinFigure1.

6. Connectthehouse wiringtothe terminalblock(Fig2.). Whenyouare sureoftheconnections wrapthe

TerminalBlockandoverlapthewiringbothsideswith2layersofinsulationtape.NOTE: This is a Class

I tting and must be earthed.The4thterminalblockconnectorisusedforthe“loop”wiresofthe“Ring

Circuit”.Theremaybemorethanonesetofcablesinthe“loop”connections.Ifthereisa“RingCircuit”and

8. Retthelid

9. Turnonthepowerandtest.

56192-Burford-bollard 20150813

Fig 1 Fig 2

Fig 3

L

N

L

N