Astonica 50104286 User manual

Type
User manual

Astonica 50104286 is a dining chair intended for residential, non-commercial use. It has a sturdy construction with a metal frame and a comfortable seat and back made of unspecified material. The chair is easy to assemble, with clear instructions and all necessary hardware included. It is designed to provide a comfortable and stylish seating solution for your dining room or other living areas.

Astonica 50104286 is a dining chair intended for residential, non-commercial use. It has a sturdy construction with a metal frame and a comfortable seat and back made of unspecified material. The chair is easy to assemble, with clear instructions and all necessary hardware included. It is designed to provide a comfortable and stylish seating solution for your dining room or other living areas.

141011ev1
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
®
Made in China
©2011 World Factory, Inc.
Distributed by:
World Factory, Inc.
Westlake, TX 76262
Model No: 50104286
Flynn Dining Chair
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
For warranty information, please refer to the back page of
this instruction manual.
Limited Warranty
World Factory, Inc. Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-422-7800 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state
to state.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
A Seat Back 1
B Seat 1
C Right Leg 1
D Left Leg 1
E 6m x 32 Bolt 8
F 6m x 15 Bolt 4
G Leg Brace 1
H Hex Key 1
1. (SEE FIGURE 1) Align the holes in seat (B) with
lower holes in the right leg (C). Secure the leg
to the seat using 6m x 32 bolt (E). Do not
fully tighten bolts.
2. Repeat the first step with left leg (D).
3. (SEE FIGURE 2) Align the holes in seat back (A)
to the upper holes in the right and left legs (C,D).
Secure the seat back to the legs using 6m x 32
bolt (E). Do not fully tighten bolts.
4. (SEE FIGURE 3) Place the leg brace (G) between
the lower part of the right and left legs (C,D).
Align the holes in the brace to the holes in the
legs and secure with 6m x 15 bolts (F). Do not
fully tighten bolts.
5. The legs should sit flat. If the chair rocks,
adjust the chair by moving the arms of the
legs up or down until all four feet of the legs
are flat. Tighten all bolts.
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A
B
C
D
ASSEMBLY INSTRUCTIONS
Figure 1
Figure 2
Figure 3
CAUTION: Do not over tighten fasteners.
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
A
B
C
D
C
NOTE: This product is intended for residential, non-commercial use.
Parts Detail
E
F
GH
E
E
E
E
D
E
E
E
E
G
F
C
D
F
F
F
  • Page 1 1
  • Page 2 2

Astonica 50104286 User manual

Type
User manual

Astonica 50104286 is a dining chair intended for residential, non-commercial use. It has a sturdy construction with a metal frame and a comfortable seat and back made of unspecified material. The chair is easy to assemble, with clear instructions and all necessary hardware included. It is designed to provide a comfortable and stylish seating solution for your dining room or other living areas.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI