Lucent Technologies Brick 350 User manual

Lucent Security Management Server

Brick® Hardware Guide

Release 8.0

260-100-002R8.0

C109542290

Version 8.0-1

January 2005

Lucent Technologies - Proprietary

This document contains proprietary information of

Lucent Technologies and is not to be disclosed or used except in

Accordance with applicable agreements

Unpublished and Not for Publication

Lucent Technologies - Proprietary

This material is protected by the copyright laws of the United States and other countries. It may not be reproduced, distributed, or

altered in any fashion by any entity (either internal or external to Lucent Technologies), except in accordance with applicable

agreements, contracts, or licens-ing, without the express written consent of Lucent Technologies and the business management

owner of the material.

Notice

Every effort was made to ensure that this information product was complete and accurate at the time of printing. However, infor-

mation is subject to change.

Mandatory customer information

Interference information: Part 15 of FCC rules

NOTE: This equipment has been tested and found to comply with limits for Class B digital device. Pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Alteration or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment.

Security Statement

In rare instances, unauthorized individuals make connections to the telecommunications network. In such an event, applicable

tariffs require that the customer pay all network charges for traffic. Lucent Technologies and its predecessors cannot be respon-

sible for such charges and will not make any allowance or give any credit for charges that result from unauthorized access.

Trademarks

VPN Firewall Brick is a registered trademark of Lucent Technologies, Inc.

Limited Warranty

For terms and conditions of sale, contact your Lucent Technologies Account Team.

Ordering Information

The ordering number for this information product is 260-100-002R8.0.

Support

Technical support

Lucent Technologies Customer Technical Assistance Management (CTAM) center provides a technical assistance telephone

number that is moni-tored 24 hours a day. For technical assistance (continental U.S.), call 1-866-LUCENT8 (1-866-582-3688)

and select appropriate prompt. For international customers, please call +1 630-224-4672.

Developed by Lucent Technologies.

Brick Hardware Guide (8.0) i

•

• • • • • •

Contents

Introduction

Brick® Models iii

Handling Brick® Components iv

How to Install a Brick® iv

Important Safety Instructions v

1 Model 20

Illustrations 1-2

Specifications 1-3

2 Model 80

Illustrations 2-2

Specifications 2-3

3 Model 150

Lucent Security Management Server (LSMS) Software Patch 3-1

Illustrations 3-2

LED Indicators 3-3

I/O Ports 3-4

Periodic Maintenance 3-4

Specifications 3-5

3-5

3-4

3-3

3-2

3-1

2-3

2-2

1-3

1-2

v

iv

iii

ii Brick Hardware Guide (8.0)

•

Contents

•

4 Model 350

Lucent Security Management Server (LSMS) Software Patch 4-1

Illustrations 4-2

LED Indicators 4-5

Periodic Maintenance 4-5

Specifications 4-5

5 Model 500

Illustrations 5-1

LAN Indicators 5-3

Specifications 5-3

6 Model 1100

Lucent Security Management Server (LSMS) Software Patch 6-2

Optimal Interface Selection 6-2

Power Supply 6-3

Illustrations 6-3

Alarm Outputs 6-7

Periodic Maintenance 6-7

Specifications 6-7

A Brick Ports

Port Matrix A-1A-1

6-7

6-3

6-2

5-3

5-1

4-5

4-2

4-1

Brick Hardware Guide (8.0) iii

•

• • • • • •

Introduction

A Brick

®

is an integrated security appliance that can be deployed in a network to

provide firewall protection and site-to-site and remote access VPN connectivity.

Brick® Models

There are six models. They are listed below and described in detail in the chapters

that follow:

• Model 20

For small office/home office (SOHO) applications.

• Model 80

For small to medium-sized offices and extranet partners.

• Model 150

For small to medium-sized offices and extranet partners.

• Model 350 (Available in AC and DC models)

For enterprise-class demands of large corporate facilities.

• Model 500

For enterprise-class demands of large corporate facilities.

• Model 1100 (Available in AC and DC Models)

For service providers offering advanced security services packages.

NOTE

Some Brick® models and configurations mentioned in this guide may no longer

be available. Contact your Lucent sales representative for current availability.

iv Brick Hardware Guide (8.0)

•

Introduction

•

Handling Brick® Components

To prevent damage to components from electrostatic discharge, always follow the

proper guidelines for equipment handling and storage. Adapter cards and

semiconductor devices in general can be easily and permanently damaged due to

electrostatic discharge during installation and removal.

In order to reduce the static potential, the user should be properly grounded through

the use of an approved antistatic wrist strap when installing, removing or handling

semiconductor components.

How to Install a Brick®

To install a Brick® 20, 80 or 500, follow the steps below. To install a Brick® 150, 350

or 1100, see the User Guides for the individual models.

1 Remove it from the carton in which it was shipped.

2 If you are installing a Model 20 or 80, locate a suitable flat surface to position the

device.

If you are installing a Model 500, you can position it in a rack. For additional security,

fasten the Brick® to the rack using the brackets on either side and a #2 Phillips-head

screwdriver.

3 If you are installing a Model 20 or 80, connect the power module and external disk

drive (if equipped) to the back. The illustrations in Chapters 1 and 2 show the location

of the appropriate ports.

If you are installing a Model 500, take the power cord that came with it and connect it

to the back. The illustrations in Chapter 5 show the location of the appropriate ports.

4 Connect the LSMS to one of the Ethernet interfaces on the back. The following

explains the type of Ethernet cable to use:

• Direct connection

If you are connecting the LSMS directly to the Brick, use a crossover Ethernet

cable.

• Hub/Switch

If you are connecting the Brick to the LSMS by means of a hub or switch, use

regular Ethernet cables from the LSMS to the hub/switch, and from the hub/switch

to the interface on the back.

5 Connect the LANs. Insert the Ethernet cable from the LANs into the remaining

Ethernet interfaces.

Keep a record of the interfaces to which the LSMS and the various LANs are

connected. You will need this information later when you create security zones and

assign them to interfaces.

Brick Hardware Guide (8.0) v

•

Introduction

•

6 Power the Brick up. It is now ready to be configured, using the LSMS (see Chapter 3.

Configuring and Activating a Brick® in the LSMS Administration Guide for

instructions).

Important Safety Instructions

The safety instructions below are applicable to the Model 20, 80 and 500 Bricks®.

For safety instructions on the Model 150, 350 and 1100 Bricks®, see the User Guides

for those models.

1 For permanently connected equipment, product installation must be performed by

trained service personnel only.

2 Read and follow all warning notices and instructions marked on the product or

included in the manual.

3 The maximum recommended operating ambient temperature is 104q Fahrenheit (40q

Centigrade). Allow sufficient air circulation or space between units when they are

installed in a closed or multirack assembly.

4 Slots and openings in the product enclosure and / or rack-mount cabinet (depending on

the design) are provided for ventilation. To ensure reliable operation of the product and

to protect it from overheating, do not block these slots and openings. Installation

without sufficient air flow can be unsafe.

5 When mounting the equipment in the rack, distribute or balance its weight to prevent

a hazardous condition due to uneven mechanical loading. The rack must safely support

the combined weight of all the equipment that it contains.

6 If your product has dual power supplies, comply with the following warning:

7 If your product does not have a power switch, comply with the following warning:

8 The power source must be adequately rated to assure safe operation of the equipment.

Make sure that the building installation and / or power source provides overload

protection.

WARNING

This unit has more than one power supply cord. Disconnect all power supply

cords before servicing to avoid electric shock.

WARNING

The power supply cord serves as the main disconnect for the product. The

socket outlet must be installed near the product and be readily accessible.

vi Brick Hardware Guide (8.0)

•

Introduction

•

9 Protective earth (PE) (main ground) connection is essential to safe operation and must

be verified before you connect to the power supply source and telecommunications

network. Do not defeat the purpose of the grounding-type plug by modifying it or using

an adapter. Use an outlet tester or a voltmeter to check the AC receptacle for the

presence of earth ground. If the receptacle is not properly grounded, do not proceed

with the installation until a qualified electrician has corrected the problem.

If the power supply is fed from a power source with no protective earthing path,

connect an earth-grounded copper wire of the proper size to the dedicated wiring

terminal marked with the protective earth (PE) symbol on the product chassis. See the

“Safety-Related Electrical, Physical and Environmental Information” appendix in

your hardware installation guide for the minimum wire size required for your product.

Models with AC power inputs are intended for use with a single phase three wire

power cord which includes an earthing conductor.

For models with DC power inputs, the protective earth (PE) connection must be

established by the dedicated earthing terminal marked with the PE symbol or, if

provided, by the earthing pin on the input terminal block.

10 Ensure that models with DC power inputs are connected to a -48V DC supply source

that is electrically isolated from the AC source in compliance with the standard and

local jurisdiction authorities of the country where you are installing the product:

UL1950 / UL 60950 in the United States

C22.2 No. 950 / No. 60950 in Canada

EN / IEC60950 in the European Union, Australia, New Zealand and Japan

11 For permanently connected equipment, the -48V DC power source must include a

double pole circuit breaker to provide a method of disconnecting the product from

power as required by national and international safety standards, and the local

jurisdiction authorities.

12 Before installing wires to the DC power terminal block, verify that these wires are not

connected to any power source. Installing live wires — wires connected to a power

source — is hazardous.

13 Do not allow anything to rest on the power cord, and do not locate the product where

people will walk on the power cord.

14 Do not attempt to service this product yourself. Opening or removing covers can

expose you to dangerous high voltage points or other risks, and may void the warranty.

Refer all servicing to qualified service personnel.

15 General purpose cables are provided with this product. Special cables, which might be

required by the regulatory inspection authority for the installation site, are the

responsibility of the customer.

Brick Hardware Guide (8.0) vii

•

Introduction

•

16 When installed in the final configuration, the product must comply with the applicable

safety standards and local jurisdiction authorities of the country where it is installed. If

necessary, consult with the appropriate regulatory agencies and inspection authorities

to ensure compliance.

17 A rare condition can create a voltage potential between the earth grounds of two or

more buildings. If products installed in separate buildings are interconnected, the

voltage potential might cause a hazardous condition. Consult a qualified electrical

consultant to determine whether or not this condition exists and, if necessary,

implement corrective action before interconnecting the products.

18 If your installation of the equipment requires that you route Ethernet cables between

buildings, use shielded and earthed Ethernet cable in this environment to protect the

equipment from possible atmospheric discharges or surges.

19 If your product has a replaceable fuse, comply with the following warning:

WARNING

For continued protection against risk of fire, replace only with a fuse of the

same type and rating.

viii Brick Hardware Guide (8.0)

•

Introduction

•

Brick Hardware Guide (8.0)

1

-

1

•

Chapter 1

• • • • • •

Model 20

A Model 20 Brick® measures approximately 6.25” x 8.75” x 1.25” and can be

positioned on a desktop or other flat surface. The vents in the Model 20 housing must

be clear of all obstructions by a minimum distance of one inch (2.54cm).

The front contains activity lights. The back has three 10/100 Base-TX Ethernet

interfaces (ether0 - ether2). It also has a 5VDC connector for the power module and a

connector for an external floppy disk drive, as well as monitor and keyboard ports.

The Model 20 comes with an external power module and an optional external 3.5”

floppy disk drive.

NOTE

For installation into networks that are subject to surges, a shielded ethernet

cable and / or serial port cable may be needed for regulatory compliance.

WARNING

For proper cooling and operation, do not stack multiple units on top of each

other.

1

-2 Brick Hardware Guide (8.0)

•

Model 20

•

Illustrations

Model 20 – Three-Quarters View

Model 20 – Front View

Model 20 – Rear View

On/Off Switch

Power Cable

Floppy Disk Drive

Serial Port

Monitor

Ether1

Ether2

Ether0

Keyboard

Port

Brick Hardware Guide (8.0)

1-

3

•

Model 20

•

Specifications

Dimensions

Height: 1.25 inches

Width: 6.19 inches

Depth: 8.63 inches

Weight

Weight: 2.25 pounds

Shipping weight: 5.2 pounds

Processor/Memory

x86 compatible 120 MHz with 64Mb RAM

LAN Interface

Ethernet: (3) 10/100 Base-TX Ethernet (RJ45)

Performance

For the latest performance, the datasheet for the Model 20 Brick® can be accessed from the

Lucent Customer Support web site at:

http://www.lucent.com/support

Hardware Assisted Encryption

Not applicable

Other Ports

SVGA video, DB9 serial, external floppy, PS/2 keyboard

Cooling

Passive Heatsink

Altitude

13,123 ft (4,000 meters)

Environmental

Operating

Temperature: 0–40º C

Shock: 2.5G at 15–20ms on any axis

Humidity: 5–95% at 40º C (non-condensing)

Vibration: 5G at 2–200 Hz on any axis

Non-Operating

Temperature: 0–70º C

Shock: 35G at 15–20ms on any axis

1

-4 Brick Hardware Guide (8.0)

•

Model 20

•

Humidity: 5–95% at 40º C (non-condensing)

Vibration: 5G at 2–200 Hz on any axis

Power

Input

Switching mode, 100 - 240VAC, 50 - 60Hz, 20 watts, 0.2A @ 115V, 0.1A @ 230V

Output

5VDC, 5A

External AC to DC power supply

rated 25W max

Switching Mode

100-240V AC, 50-60 Hz

Consumption

0.19A typical @ 115V AC

Brick Hardware Guide (8.0)

1-

5

•

Model 20

•

Product Safety and Emissions Certifications

Safety Listings

USA – UL 1950

Canada – CSA 22.2 No. 950

EU – EN/IEC 60950

Japan – CB Scheme 1EC60950

EMC Listings

USA – FCC Part 15, Class B

Canada – IC-ES003

EU – EMC Directive

Japan – VCCI

NEBS Certification

Not applicable

ICSA Certification

ICSA V4.0 Firewall Certified

ICSA V1.0B IPSec Certified

1

-6 Brick Hardware Guide (8.0)

•

Model 20

•

Brick Hardware Guide (8.0)

2

-

1

•

Chapter 2

• • • • • •

Model 80

A Model 80 Brick® measures approximately 7.5” x 11” x 2” and comes with “feet”

on the bottom so that it can be mounted on any flat surface. The vents in a Model 80

Brick housing — top and side — must be clear of all obstructions by a minimum

distance of 1 inch (2.54 cm).

The front contains activity lights. The back has four 10/100 Base-TX Ethernet

interfaces (ether0 - ether3). It also has a 5VDC connector for the power module and a

connector for an external floppy disk drive, as well as monitor and keyboard ports.

The Model 80 also comes with an external power module and an external 3.5” floppy

disk drive.

NOTE

For installation into networks that are subject to surges, a shielded ethernet

cable and / or serial port cable may be needed for regulatory compliance.

WARNING

For proper cooling and operation, do not stack multiple units on top of each

other.

2

-2 Brick Hardware Guide (8.0)

•

Model 80

•

Illustrations

Model 80 – Three-Quarter View

Model 80 – Front View

Model 80 – Rear View

Power Cable

Keyboard

Floppy Disk

Ether0

Monitor

On/Off Switch

Drive

Serial Port

Ether1

Ether2

Ether3

Port

Brick Hardware Guide (8.0)

2-

3

•

Model 80

•

Specifications

Dimensions

Height: 2.00 inches (5.08 cm)

Width: 11.13 inches (28.26 cm)

Depth: 7.5 inches (19.05 cm)

Weight

Weight: 3.1 pounds (1.4 kg)

Shipping weight: 7.5 pounds (3.4 kg)

Processor/Memory

AMD K6-2 350 MHz with 64MB RAM

LAN Interface

Ethernet: (4) 10/100 Base-TX Ethernet (RJ-45)

Performance

For the latest performance, the datasheet for the Model 80 Brick can be accessed from the

Lucent Customer Support web site at:

http://www.lucent.com/support

Hardware Assisted Encryption

Not applicable

Other Ports

SVGA video, DB9 serial, external floppy, PS/2 keyboard

Cooling

CPU fan

Altitude

10,000 feet (3,048 meters)

Environmental

Operating

Temperature: 0–40º C

Shock: 2.5G at 15–20ms on any axis

Humidity: 5–95% at 40º C (non-condensing)

Vibration: 5G at 2–200 Hz on any axis

2

-4 Brick Hardware Guide (8.0)

•

Model 80

•

Non-Operating

Temperature: 0–70º C

Shock: 35G at 15–20ms on any axis

Humidity: 5–95% at 40º C (non-condensing)

Vibration: 5G at 2–200 Hz on any axis

Power

External AC to DC Power Supply

rated 40W max

Input

Switching mode, 100 - 250VAC, 50 - 60Hz, 27 watts

Typical Consumption

0.27A @ 115V, 0.13A @ 230V

Product Safety and Emissions Certifications

Safety Listings

USA – UL1950

Canada – CSA 22.2 No. 950

EU – EN/1EC 60950

Japan – CB Scheme 1EC 60950

EMC Certifications

USA – FCC Part 15, Class A

Canada – IC-ES003

EU – EMC Directive

Japan – VCCI

NEBS Certification

Not applicable

ICSA Certification

ICSA 4.0 Firewall Certified

ICSA 1.0B IPSec Certified

Page is loading ...

Lucent Technologies Brick 350 User manual

This manual is also suitable for

Lucent Technologies Brick 350 User manual

Related papers

Other documents