Focal Point Mora Create Alpine AMRC-ALP Installation guide

1 of 9

IS0792 REV. B

AirCore® Technology

Mora®

AMR | AUMR | AMRC | AUMRC

BEFORE YOU BEGIN COMPONENT KEY

FOCAL POINT

• Configurations are run specific, please

consult factory drawings before

beginning installation.

• Luminaires must be installed by a qualified

electrician (check with local and national

codes for proper installation).

• To prevent electrical shock, disconnect

electrical supply before installation or

servicing.

• Contractor is responsible for adequately

reinforcing walls and/or ceilings to support

fixture weight.

• Focal Point, LLC accepts no responsibility

for inadequately reinforced walls and/or

ceilings.

• The information contained in this drawing

is the sole property of Focal Point, LLC. Any

reproduction in part or whole without the

written permission of Focal Point, LLC is

prohibited.

POWER OFF

POWER ON

ATTENTION

SEE ADDITIONAL

INSTRUCTIONS

INSTRUCTION KEY

Flat Washer

1.5" x .281" x .062"

(75221)

Bolt

1/4-20 x 4.5"

(700547)

SEEM  ACOUSTIC

TRUBLADE

DIRECT TO STRUT HARDWARE

SHIPPED IN BAG

SEEM  ACOUSTIC DIRECT TO STRUT INSTALLATION  PG 

SEEM  ACOUSTIC AIRCRAFT CABLE INSTALLATION  PG 

TRUBLADE STRUTKLIP INSTALLATION  PG 

TRUBLADE MAGNET INSTALLATION  PG 

TRUBLADE AIRCRAFT CABLE INSTALLATION  PG 

MULTIPLE ARRAY INSTALLATION  PG 

SEEM  ACOUSTIC LUMINAIRES

MUST BE INSTALLED PRIOR TO

INSTALLING TRUBLADE BAFFLES

Aircraft Cable

with Stop Sleeve

(73060-XX)

StrutKlip

(A55717-01)

STRUTKLIP HARDWARE

SHIPPED IN BAG

AIRCRAFT CABLE SUSPENSION

HARDWARE SHIPPED IN BAG

Cable

Coupler

(73650)

4"

6" 12"

6"

4"

12"

4"

6" 12"

6"

4"

12"

Spacer Tool

(A59289)

INSTALLATION TOOL

SHIPPED IN PACKAGING

2 of 9

IS0792 REV. B

FACTORY DRAWINGS

TRUBLADE INSTALLATION SEQUENCE

Each TruBlade bale is labeled with a fixture key that is aixed to the extrusion. DO NOT REMOVE LABEL.

Match the fixture key on the factory drawing with the

corresponding fixture key on the TruBlade bale to

determine the installation sequence.

Ensure all TruBlade bales are installed with the fixture

key facing the same direction.

QTY 1 SEEM 1 LUMINAIRE

QTY 48 TRUBLADE

CONSULT FACTORY DRAWINGS FOR MOUNTING LOCATIONS AND OTHER INSTALLATION DIMENSIONS

WA-U1

3 of 9

IS0792 REV. B

STRUT INSTALLATION

AVOID INSTALLING STRUT SUSPENSION RODS

AND BOLTS AT MOUNTING LOCATIONS

SPACER TOOL

INSTALLATION METHOD STRUT ORIENTATION

Seem 1 Acoustic Direct to Strut Strut can be installed in "n" or "u" orientation

Seem 1 Acoustic Aircraft Cable Strut can be installed in "n" or "u" orientation

TruBlade StrutKlip Strut must be installed in "n" orientation

TruBlade Magnet Strut must be installed in "u" orientation

TruBlade Aircraft Cable Strut can be installed in "n" or "u" orientation

STRUT FOR SEEM  ACOUSTIC INSTALLS PERPENDICULARLY

ABOVE STRUT FOR TRUBLADE BAFFLES

4"

6"

12"

4"

6" 12"

6"

4"

12"

4"

6" 12"

6"

4"

12"

Bend spacer tool at perforation

for 6" on-center spacing

Use the provided spacer tool to evenly space and install TruBlade bales.

6"

4"

12"

4"

6"

4"

6" 12"

4" on-center spacing 6" on-center spacing 12" on-center spacing

4 of 9

IS0792 REV. B

SEEM  ACOUSTIC DIRECT TO STRUT INSTALLATION

STRUT CAN BE INSTALLED

IN "n" OR "u" ORIENTATION

FOR CONTINUOUS RUNS MORA CREATE

FOLLOW FOCAL POINT INSTRUCTIONS

FOR SEEM  ACOUSTIC

DIRECT TO STRUT JOINING

SEE IS

AVOID INSTALLING STRUT

SUSPENSION RODS AND BOLTS AT

SEEM  ACOUSTIC MOUNTING LOCATIONS

2b

3a 3b

12a

Strut for Seem 1 Acoustic installs

perpendicularly above strut for TruBlade baes.

4.625"

1.87"

3.00"

9.25"

Center Seem 1 Acoustic between TruBlade baes. Refer to factory drawings for specic installation dimensions.

4

MAKE ELECTRICAL CONNECTION

5 of 9

IS0792 REV. B

Adjust mounting bolt depth so that the top of Seem 1 Acoustic is flush with the top of TruBlade bales

5

3

1

HARDWARE BY OTHERS

/" 

THREAD

2a 2b

Strut for Seem 1 Acoustic installs

perpendicularly above strut for TruBlade baes.

4.625"

1.87"

3.00"

9.25"

Center Seem 1 Acoustic between TruBlade baes. Refer to factory drawings for specic installation dimensions.

SEEM  ACOUSTIC AIRCRAFT CABLE INSTALLATION

FOLLOW FOCAL POINT INSTRUCTIONS

FOR SEEM  ACOUSTIC

SUSPENDED JOINING

SEE IS

AVOID INSTALLING STRUT

SUSPENSION RODS AND BOLTS AT

SEEM  ACOUSTIC MOUNTING LOCATIONS

STRUT CAN BE INSTALLED

IN "n" OR "u" ORIENTATION

6 of 9

IS0792 REV. B

456

MAKE ELECTRICAL CONNECTION

Adjust cable height so that the top of Seem 1 Acoustic is flush with the top of TruBlade bales

7

3

11

2

Rotate StrutKlip 90° to lock into place

Use spacer tool to evenly space and

install the remaining StrutKlip fasteners.

Refer to factory drawings for

specic installation dimensions.

1a

Insert StrutKlip lengthwise into strut channel

TRUBLADE STRUTKLIP INSTALLATION

STRUT MUST BE INSTALLED

IN "n" ORIENTATION

AVOID INSTALLING STRUT

SUSPENSION RODS AND BOLTS AT

TRUBLADE MOUNTING LOCATIONS

1b

Insert StrutKlip lengthwise into strut channel

4"

6" 12"

6"

4"

12"

4"

6" 12"

6"

4"

12"

7 of 9

IS0792 REV. B

3

11

1

2

Magnet is preinstalled

on TruBlade bae

Attach TruBlade bae directly to strut

TRUBLADE MAGNET INSTALLATION

STRUT MUST BE INSTALLED

IN "u" ORIENTATION

Use spacer tool to evenly space

and install the remaining TruBlade baes.

Refer to factory drawings for specic installation dimensions.

AVOID INSTALLING STRUT

SUSPENSION RODS AND BOLTS AT

TRUBLADE MOUNTING LOCATIONS

7

511

6

Ensure StrutKlip fully engages with TruBlade extrusion

Install remaining TruBlade baes

Install TruBlade bae

4

Repeat installation of StrutKlip fasteners on second unistrut row

8

Center and align edges of TruBlade baes to ensure ush installation

4"

6" 12"

6"

4"

12"

4"

6" 12"

6"

4"

12"

8 of 9

IS0792 REV. B

6

Install remaining TruBlade baes

2

Use spacer tool to evenly space and

install the remaining suspension points.

Refer to submittal drawings for specic installation dimensions.

5

4

3a 3b

TRUBLADE AIRCRAFT CABLE INSTALLATION

1

HARDWARE BY OTHERS

/" 

THREAD

AVOID INSTALLING STRUT

SUSPENSION RODS AND BOLTS AT

TRUBLADE MOUNTING LOCATIONS

4

Center and align edges of TruBlade baes to ensure ush installation

4"

6" 12"

6"

4"

12"

4"

6" 12"

6"

4"

12"

STRUT CAN BE INSTALLED

IN "n" OR "u" ORIENTATION

9 of 9

IS0792 REV. B

MULTIPLE ARRAY INSTALLATION

." MINIMUM SPACING RECOMMENDED BETWEEN ARRAYS.

REFER TO RCP REFLECTED CEILING PLAN FOR EXACT DIMENSIONS.

7

Level and align top of TruBlade baes to ensure ush installation

." SPACING BETWEEN ARRAY MOUNTING LOCATIONS.

Focal Point Mora Create Alpine AMRC-ALP Installation guide

This manual is also suitable for

Focal Point Mora Create Alpine AMRC-ALP Installation guide

Related papers

Other documents