ShenZhen Keymantek K36 is a Hand-held Terminal which runs on Microsoft Windows CE.Net 6.0 and has a 256M Flash ROM, 64M DDR2 memory, a 400 MHz Processor, 2.8 inches TFT High-reliability adjustable LED Display with 240x320 resolution and a 2800mAh lithium-ion battery. It includes a stylus, USB cable, charger, and lithium-ion battery. The K36 is IP54 and can withstand being dropped from a height of 1.2 meters. It supports WiFi, GPRS, GPS and BlueTooth for communication, can scan 1D and 2D barcodes, and can read RFID tags using 125KHz, 134.2KHz, and 13.56MHz frequencies.
ShenZhen Keymantek K36 is a Hand-held Terminal which runs on Microsoft Windows CE.Net 6.0 and has a 256M Flash ROM, 64M DDR2 memory, a 400 MHz Processor, 2.8 inches TFT High-reliability adjustable LED Display with 240x320 resolution and a 2800mAh lithium-ion battery. It includes a stylus, USB cable, charger, and lithium-ion battery. The K36 is IP54 and can withstand being dropped from a height of 1.2 meters. It supports WiFi, GPRS, GPS and BlueTooth for communication, can scan 1D and 2D barcodes, and can read RFID tags using 125KHz, 134.2KHz, and 13.56MHz frequencies.
1
Warning ：Please read the followings before operating the terminal.
Do not take the battery out when it is charging.
Disassembling the terminal and/or any damage to the surface should void the warranty.
Keep the display screen free from any kind of stress. Keymantek is not responsible for
that damages.
Back up data in time.
Keymantek is not responsible for any loss because of losing data
when the terminal is using.
Keep the terminal away from static and/or strong electromagnetic radiation.
There is a lithium-ion battery in the terminal.
Do not try to disassemble ,crush or pierce
the battery. Dispose the battery according to local law or EHS guidance.
Do not install any other program,except permitted by Keymantek.
The material in this manual is subject to change without notice.
2
Chapter 1 Basic informations .................................................4
1.1Performance ..............................................................................4
1.2 Buttons ..................................................................................5
1.3 Accessories ............................................................................7
Chapter 2 Getting Start ...................................................................8
2.1 Installing & Changing Battery ...................................................8
2.2 Power on & Power off ..............................................................8
2.3 Charging the Battery .............................................................. 11
2.4 Sleep & Wakeup .................................................................... 12
2.5 Taskbar ................................................................................... 13
2.6 Desktop .................................................................................. 14
2.7 Resetting the Terminal .......................................................... 15
Chaper 3 Settings ................................................................. 16
3.1 Settings .................................................................................. 18
3.2 Power ..................................................................................... 19
3.3 Password ................................................................................ 20
3.4 Regional Settings ................................................................... 21
3.5 Date/Time .............................................................................. 23
3.6 Owner ............................................................................... 24
3.7 System.................................................................................... 26
3.8 Display .................................................................................... 28
3
3.9 K36 Hand-held Function use ............................................ 29
Chapter 4 Keyboard & Input mode .............................................. 33
4.1 Keyboard ................................................................................ 33
4.2 Input panel ............................................................................. 33
Chapter 5 Installing & Removing software .................................. 35
5.1 Directory ................................................................................ 35
5.2 Installing Microsoft ActiveSync .............................................. 36
5.3 How to install software .......................................................... 37
5.3.1 Preparation： .................................................................. 37
5.3.2 Install software in your terminal： ................................. 37
5.3.3 How to execute files： ................................................... 37
Appendix 1 Troubleshooting ....................................................... 38
Device&System problem ............................................................. 38
2、Communication problem ....................................................... 39
Appendix 3 Customer Service ...................................................... 40
Appendix 4 Others ....................................................................... 40
4
Chapter 1 Basic informations
1.1Performance
Item Description
OS Microsoft Windows CE.Net 6.0
CPU s3c2416 400 MHz Processor
Memory 256M Flash ROM, 64M DDR2
Display
QVGA 2.8 240 x320 resolution, Transflective, portrait mode
TFT High-reliability adjustable LED
function
IRDA METER
additional SYMBOL engine(1D)
additional RFID (125KHz、134.2KHz、13.56MHz)
WIFI、GPRS、GPS、BlueTooth
Backup SD card & FLASH
Develop
environment VS.NET 2008
Battery 2800mAh lithium-ion battery
IP & Drop test Test per IEC60529/IP54, 1.2 meter/6 times drop to concrete
Temperature Operatingtemperature:-20℃-50℃
Storage temperature:-25℃ to 55℃
5
Communicate on
USB /Wifi/CDMA/GPRS/Bluetooth optional
Storage Micro SD card（16GB MAX）
Dimensions 156mm*71.5mm*26/32mm
Weight 285g
1.2 Buttons
Key Action
Power key.Press the key to turn the terminal on when
off.Pres
s the key to enter suspend/wakeup status.Press the
key for 3 seconds to turn the terminal off.
Combination function key
Combination function key
Left Scan button
Right Scan button
Direction key-Left
Direction key-Right
Direction key-Up
7
Numeric
-9WXYZ
Numeric
-0 and Space
Switch input method
1.3 Accessories
Item Quantity
Remark
Terminal 1pc
Stylus 1pc
USB cable 1pc
Allows USB connection from the terminal to a host
computer,allows charging of the te
rminal through
the cable.
Charger 1pc For charging the battery and set
Lithium-ion
battery
1pcs
8
Chapter 2 Getting Start
2.1 Installing & Changing Battery
1. Be sure that the Terminal is turned off;
2. Unlock the Battery Cover;
3. Remove the Battery Cover;
4. Insert battery in the battery compartment with the tie on the
battery;
5. Replace the battery cover by inserting the top first;
6. Lock the Battery Lock.
2.2 Power on & Power off
1. Power on
Insert battery in the battery compartment，Press the button，
then the splash screen displays（See Figure 2-1）， When the
9
initialization finish，then you can see the WinCE（See Figure 2-2）.
Figure 2-1 Figure 2-2
Please calibrate the screen when turning on the terminal for the
first time.
(1)Click the button on the desktop，Select
"Settings"->"Control Panel"。
(2)Select "Stylus"(See Figure2-3)，and double-click。
Figure 2-3
(3)Select“Calibration”，then click the “Recalibrate”button(See
Figure2-4)。
11
Figure 2-5
You can recalibrate the screen at anytime.
2. Power off
Please close all programs before turning the terminal off.
Press button for more than 3 seconds,the display will be closed,
Power LED is off, terminal closed. (See Figure2-6)
Figure 2-6
2.3 Charging the Battery
1. Insert the battery into the terminal compartment and charge the
battery with USB charger.
Note：Turn the terminal off before charging.
When the picture（See Figure 2-7-1/Figure 2-7-2）appears ,battery need to
be recharged.
12
Figure 2-7-1 Figure 2-7-2
2.4 Sleep & Wakeup
(1). Sleep
Just press (more than 3 seconds)to set the terminal in sleep
stae when the terminal is power on.Keyboard and/or touchpad does not
respond unless the terminal wakes up.
The terminal will sleep if there is no operation for a long time when
the terminal is on.See 3.2 for setting the time.
2. Wakeup
Press to wake the terminal when the terminal is in sleep mode.
Note：Frequently press in a short time(10 seconds)may result in
losing data and display damage.
13
2.5 Taskbar
The Taskbar at the bottom of the window displays the active
programs，See Figure2-8：
Figure 2-8
Start Icon is used to quickly start a program,find a file,access
the settings window or access help.（See Figure 2-9）。
Figure 2-9
Icon，is used to toggle betwen different input modes(with input
panel) （See Figure 2-10-1、2）
Figure 2-10-1 Figure 2-10-2
14
Icon，to indicate current task,toggle between different tasks.
（See Figure 2-11）
Figure 2-11
Icon,is used to indicate the current time.You can also change it by
double-clicking the icon.Select ->"Settings"->"Taskbar and Start
Menu"-“Show Clock” to show/hide the clock. （See Figure 2-12-1、2）
Figure 2-12-1 Figure 2-12-2
2.6 Desktop
The desktop window appears when power on the termnal
A menu will appear when you keep pressing the touchpad （See
Figure 2-13-1、2、3）
15
Figure 2-13-1
Figure 2-13-2 Figure 2-13-3
2.7 Resetting the Terminal
If the terminal stops responding to input,reset it.
Insert the stylus into Reset Port（See Figure 2-14） ， for more than
1 second to reset the terminal.You can also release battery , install
battery and power it on to reset.
Desktop
17
Icon Description
View the settings and change the system settings.
Calibrate the touch screen.See Chapter 2.5 for more
information.
View battery status and change power management options.
Change owener's password and set security options.
Set how numbers,currencies,dates,and times are displayed.
Change date,time and time zone information.
18
Change owener's personal profiles.
View system information,and change memory settings.
Display settins, set desktop background, appearance
,
backlight,and brightness.
Note：Do not change the settings which is not on the above table.
3.1 Settings
Select "Control Panel"-" Settings" to change system settings.(See Figure
3-3/Figure 3-4).
Attribute:Display terminal system data.
Figure 3-3 Figure 3-4
19
Parameter Setting tab:Display terminal configuration data.
3.2 Power
Select "Control Panel"-"Power",you can see the status of the main
and backup batteries and set power management options.
Battery tab:provide general information on battery conditions.The
amount of useful operating time remaining varies depending on battery
type and how you use the terminal.
Figure 3-5 Figure 3-6
Schemes tab:you can choose "Battery Power" or "AC Power" in
Power Scheme. （See Figure 3-5、3-6）
Tap to save, to cancel.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
ShenZhen Keymantek K36 is a Hand-held Terminal which runs on Microsoft Windows CE.Net 6.0 and has a 256M Flash ROM, 64M DDR2 memory, a 400 MHz Processor, 2.8 inches TFT High-reliability adjustable LED Display with 240x320 resolution and a 2800mAh lithium-ion battery. It includes a stylus, USB cable, charger, and lithium-ion battery. The K36 is IP54 and can withstand being dropped from a height of 1.2 meters. It supports WiFi, GPRS, GPS and BlueTooth for communication, can scan 1D and 2D barcodes, and can read RFID tags using 125KHz, 134.2KHz, and 13.56MHz frequencies.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI