Watts RadiantPEX-AL PressAll Tools User guide

Type
User guide
PRESS-ALL TOOLS
A money-saving tool.
Both Press and Crimp jaws fit our new PressAll tool.
And both sets of jaws fit the CrimpAll tool, as well. No matter which
tool you own, you can simply buy a jaw set to double your tool’s capability.
Press connection
15” PressAll tool, 15” jaws and 15” crimping jaws shown.
Both the 15” and the
19” tool kits contain
an adjustable
wrench and jaw
changing tool.
Instructions for
adjustment, jaw
replacement and
making Press connections
are permanently labelled inside the lid.
5/8” Press jaws
3/4” Press jaws
1/2” Press jaws
3/8” Crimp jaws
1/2” Crimp jaws
5/8” Crimp jaws
3/4” Crimp jaws
Crimp ring connection
© 2006 Watts Radiant, Inc. PressAll Tool Product Sheet LIT#PressToolProd-0906 Effective: 09/01/2006
Tools and Accessories
RadiantPEX-AL Press Tools Order # Model # Pkg Wt UPC
15” Manual Pressing
T
ool Kit w/ 1/2”, 5/8”, 3/4” jaws
81008140
RLP
A-0612-K1 1 6 lb 840213083922
19” Manual Pressing
T
ool Kit w/ 1/2”, 5/8”, 3/4”, 1” jaws 81008142 RLPA-0624-K2 1 8 lb 840213083939
15” Press
Tool, Extra Jaws Kit - 1/2”, 5/8”, 3/4” 81008426 RLPAJ19-K1 1 3 lb 840213083984
19” Press Tool, Extra Jaws Kit - 1/2”, 5/8”, 3/4”, 1” 81008427 RLPAJ19-K2 1 3 lb 840213084035
R
adiantPEX Crimp
T
ools
Order #
Model #
Pkg
Wt
UPC
15” CrimpAll
Tool, Extra Jaws Kit - 3/8”, 1/2”, 5/8”, 3/4” 81009022 PCCRT-15K1 1 3 lb 840213084363
INTERCHANGEABLILITY
. Big word. Simple concept.
Watts Radiant introduces one tool to fit two sets of interchangeable jaws.
Use your CrimpAll or PressAll tool to make both types of connection. Two types
of pipe, two types of fittings, multiple sizes... one tool does them all!
Codes, Listings, and Standards.
RadiantPEX-AL tubing and Press fittings are manufactured in accordance with
American Standard Testing Methods (ASTM) F-1281, are tested and listed by the
National Sanitation Foundation (NSF-PW Standards 14 and 61 and NSF-rfh), and
carry the UPC certification mark, as approved by the International Association of
Plumbing and Mechanical Of
ficials (IAPMO).
®
PressAll Jaw Installation
1. 2. 3
and4.
1. Cut a clean, square end to the tube.
2. Use the Reamer tool to shape and prep the tubing.
3. Make sure the Press sleeve is seated in the plastic
base of the connection with the view ports against
the plastic base.
4. Slide the RadiantPEX-AL tubing onto the fitting until
the tubing visibly fills the view port.
5. Place the Press fitting into one side of the jaws.
6. Close the jaws firmly. Tool will stop automatically
when complete.
7. See specific tool instruction sheet for
maintenance information.
Completed Press connection
Uncompleted Press connection
5. 6.
PressAll Tool Adjustment
Completing a PressAll Fitting
Set Screw
Loosen before each adjustment.
Tighten after each adjustment.
Crescent Wrench (Included in kit)
Adjustment Screw
Tighten for more crimping force.
Loosen for less crimping force.
Do NOT loosen
View Port
View Port
Reamer
Tool
15” PressAll
Tool Kit; 19” PressAll
Tool Kit
15” Kit Components
1/2" Jaws
3/4" Jaws
5/8" Jaws
Extra Jaw Retaining Screws
and Lock Washers
Hex tool for
changing jaws
15” PressAll Tool
PressAll Adjustment Tool
19” Kit Components
1/2" Jaws 3/4" Jaws 5/8" Jaws
Extra Jaw Retaining Screws and Lock Washers
19” PressAll Tool
1" Jaws
PressAll Adjustment Tool
Hex tool for jaw change out
© 2006 Watts Radiant, Inc. PressAll Tool Product Sheet LIT#PressToolProd-0906 Effective: 09/01/2006
In the United Sta
tes
W
a
tts R
adiant,
Inc
.
4500 Progress Place
Springfield, MO 65803
1-800-276-2419
toll-free
417-864-6108 phone
417-864-8161 fax
www
.wattsradiant.com
In Canada
W
a
tts Industrie
s
Canada
5435 North Service Road
Burlington, ON L7L 5H7
1-888-208-8927
toll-free phone
905-332-4090 phone
1-888-882-1979 toll-free fax
905-332-7068 fax
www.wattscanada.ca
  • Page 1 1
  • Page 2 2

Watts RadiantPEX-AL PressAll Tools User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI