PAC BKHONK837 User manual

PAC
Brand
PAC
Model
BKHONK837
Type
User manual

This manual is also suitable for

PAC BKHONK837 allows you to mount an aftermarket radio in Honda 2012 CIVIC car models. The kit includes metal panel fastener clips, screws, and a trim ring. The installation process involves removing the factory dash panel, attaching the metal panel fastener clips to the mounting tabs on the back side of the main panel, removing the four shaded brackets from the trim ring, inserting the pocket into the lower section of the kit, inserting the trim into the main frame, installing the brackets to the rear of the main frame, and inserting the ISO mountable radio between the ISO mount brackets.

PAC BKHONK837 allows you to mount an aftermarket radio in Honda 2012 CIVIC car models. The kit includes metal panel fastener clips, screws, and a trim ring. The installation process involves removing the factory dash panel, attaching the metal panel fastener clips to the mounting tabs on the back side of the main panel, removing the four shaded brackets from the trim ring, inserting the pocket into the lower section of the kit, inserting the trim into the main frame, installing the brackets to the rear of the main frame, and inserting the ISO mountable radio between the ISO mount brackets.

TECH Ver. 7/16 PRINT Ver. 7/16
iHONK837
VEHICLE APPLICATION
Honda
2012 CIVIC
www.bestkits.com www.aampglobal.com www.aius.net
2500 East Francis Street Ontario, CA 91761, U.S.A.
Sales: (800) 477-2267
Intl: (727) 572-9255
Support: 888-228-5560
HONK837 Mounting Kit
DASH DISASSEMBLY INSTRUCTIONS
1. Remove small cover located under the HVAC (2 screws).
2. Remove the 2 screws holding the factory radio mounting brackets.
3. Carefully remove the factory dash panel located above the instrument cluster,
far enough to allow the factory radio to be removed.
4. Remove the factory radio.
2
3
DOUBLE DIN INSTALLATION INSTRUCTIONS
KIT PREPARATION
1. Attach the metal panel fastener clips (included with kit) (5) to each mounting
tab on the back side of the main panel.
2. Remove the 4 tabs shown (shaded) below from the trim ring.
1. Insert trim into the main frame.
2. Install brackets to rear of main frame (Do Not Overtighten)using 4 screws supplied
3. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or screws supplied with kit.
4. Slide radio forward or backward for desired look and tighten screws.
5. Install clips provided with kit to lower bracket location. Once kit is installed use
the 5/8 screws also provided with the kit to securely mount the brackets to the
sub-dash(Suggested).
SINGLE ISO INSTALLATION INSTRUCTIONS
1. Insert pocket into lower section of kit from rear & lock into slots of mounting brackets.
2. Insert trim into the main frame.
3. Install brackets to rear of main frame (Do Not Overtighten)using 4 screws supplied
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or screws supplied with kit.
5. Slide radio forward or backward for desired look and tighten screws.
6. Install clips provided with kit to lower bracket location. Once kit is installed use
the 5/8 screws also provided with the kit to securely mount the brackets to the
sub-dash(Suggested).
INSTALL CLIPS HERE ON BOTH
LEFT & RIGHT BRACKETS
(Flat side of the clip on the bottom)
Figure C
REMOVE SHADED TABS
ON BOTH LEFT
& RIGHT BRACKET
INSTALL CLIPS HERE ON BOTH
LEFT & RIGHT BRACKETS
(Flat side of the clip on the bottom)
Figure A
REMOVE ALL
4 SHADED BRACKETS
Figure B
  • Page 1 1
  • Page 2 2

PAC BKHONK837 User manual

PAC
Brand
PAC
Model
BKHONK837
Type
User manual
This manual is also suitable for

PAC BKHONK837 allows you to mount an aftermarket radio in Honda 2012 CIVIC car models. The kit includes metal panel fastener clips, screws, and a trim ring. The installation process involves removing the factory dash panel, attaching the metal panel fastener clips to the mounting tabs on the back side of the main panel, removing the four shaded brackets from the trim ring, inserting the pocket into the lower section of the kit, inserting the trim into the main frame, installing the brackets to the rear of the main frame, and inserting the ISO mountable radio between the ISO mount brackets.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents