PAC APH-CH01 User manual

APH-CH01
PAC
Brand
PAC
Model
APH-CH01
Category
Car speakers
Type
User manual

PAC APH-CH01 simplifies speaker wire connections when adding aftermarket amplifiers to select Chrysler, Dodge, Jeep, and Ram vehicles with factory amplified sound systems, eliminating the need to cut or modify the original wiring. Each wire pair is labeled for easy identification. It features pass-through connections for CAN +, CAN -, left and right front and rear inputs, and constant 12 volts. The harness connects to the factory amplifier's 22-pin and 16-pin connectors.

PAC APH-CH01 simplifies speaker wire connections when adding aftermarket amplifiers to select Chrysler, Dodge, Jeep, and Ram vehicles with factory amplified sound systems, eliminating the need to cut or modify the original wiring. Each wire pair is labeled for easy identification. It features pass-through connections for CAN +, CAN -, left and right front and rear inputs, and constant 12 volts. The harness connects to the factory amplifier's 22-pin and 16-pin connectors.

Speaker connection harness for select
2007-2017 Chrysler Dodge Jeep and Ram
vehicles with factory amplied sound systems
Pacific Accessory Corporation
Page 1
Copyright © 2018. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
APH-CH01
Rev: V1
Date: 042518
12
1
22
13
Black
Green / Red
Pink
Gray / Blue
Green / Purple
Pink / Black
1
12
13
22
Black
Pink
Pink / Black
Yellow
White / Blue
Yellow
Gray / Red
White / Red
Black / RedBlack / Green
Green
Green / Black
Purple
Purple / Black
White
White / Black
Gray
Gray / Black
Green
Green / Black
Purple
Purple / Black
White
Gray / Black
Gray
White / Black
Gray / Blue
Grey / Red
White / Blue
White / Red
Green / Red
Green / Purple
Black / Red
Black / Green
APH-CH01
Introduction and Features
The APH-CH01 simplies speaker wire connections when adding aftermarket ampliers. Aftermarket ampliers can
be easily added with no need to cut or modify a vehicle’s original wiring. Each pair of wires has been labeled with the
corresponding speaker name.
Wiring Overview
Harness 1 (White Connector):
Installation Notes
1. It is always best to use a tone generator (PAC Part# TL-PTG2) to verify that the tables in this manual, and the labels on the
wires, match the wiring in your specic vehicle.
2. Connection of the male Black 16-pin connector is only necessary if you are leaving factory speakers connected to the factory
amplier.
3. The White 22-pin connector from the APH-CH01 must be connected to the factory amplier when using a PAC AmpPRO
Interface.
4. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It is
important to understand which speakers the vehicle is equipped with.
5. If you are leaving any of the factory speakers connected to the factory amplier, simply connect the speaker wires (color for
color) between the male and female connectors. For example: If you want the rear speakers to be powered by the factory
amplier, simply connect the Green, Green / Black, Purple and Purple / Black wires from the male connector to the Green,
Green / Black, Purple and Purple / Black wires from the female connector.
1 Black Pass through (Ground)
12 Yellow
Pass through (Constant 12v)
2
Pink Passthrough(CAN+)
13 Pink/Black
Pass through (CAN -)
4
Green
15 Green/Black
5 Purple
16 Purple/Black
6 White
17 White/Black
7 Gray
18 Gray/Black
8 Gray / Blue Front Right Tweeter -
19
Gray/Red Front Right Tweeter +
9
White/Blue Front Left Tweeter -
20
White/Red Front Left Tweeter +
10 Green / Red Rear Left Tweeter +
21
Green/Purple Rear Left Tweeter -
11
Black/Red Sub 2 +
22
Black/Green Sub 2 -
RearLeftTweeter
Pin Number Wires Description
Label
Pass through (Left Rear Input)
Wire Color
Pass through (Right Rear Input)
Pass through (Left Front Input)
Pass through (Right Front Input)
FrontRightTweeter
FrontLeftTweeter
Subwoofer2
1. Locate the vehicles factory amplier and disconnect the White 22-pin and Black 16-pin connectors.
2. Connect the APH-CH01 harness to the connectors that were disconnected in the previous step.
3. Connect the male connectors from the APH-CH01 to the amplier.
4. Connect the longer loose wires from the APH-CH01 to your aftermarket amplier or passive crossovers according to the tables
in this manual.
Installation Steps
Connect to aftermarket amplier
or passive crossover.
Speaker connection harness for select
2007-2017 Chrysler Dodge Jeep and Ram
vehicles with factory amplied sound systems
Pacific Accessory Corporation
Page 2
Copyright © 2018. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
APH-CH01
Rev: V1
Date: 042518
Wiring Overview (cont.)
Harness 2 (Black Connector):
1
8
9
16
1
8
9
16
Purple
Blue / Black
Green / Black
Brown
Black / White
Gray
White
Orange
White
Orange
Blue / Black
Brown
Purple
Green / Black
Black / White
Gray
Blue / Red
Orange / Black
Brown / Black
Purple / Black
Green
Black
Gray / Black
White / Black
Black
Green
Purple / Black
Brown / Black
Blue / Red
Orange / Black
Gray / Black
White / Black
APH-CH01
APH-CH01
1 Orange For Future Use
9
Orange/Black For Future Use
2 Blue / Black Rear Right Tweeter -
10
Blue/Red Rear Right Tweeter +
3 Brown Center Channel +
11
Brown/Black Center Channel -
4 Purple Rear Right Midrange +
12
Purple/Black Rear Right Midrange -
5 Green / Black Rear Left Midrange -
13
Green Rear Left Midrange +
6
Black/White Sub 1 -
14
Black Sub 1 +
7
Gray Front Right Midrange +
15
Gray/Black Front Right Midrange -
8
White Front Left Midrange +
16
White/Black Front Left Midrange -
FrontRightMidrange
Pin Number Wires Description
Label
Wire Color
RearRightTweeter
CenterChannel
RearRightMidrange
RearLeftMidrange
Subwoofer1
FrontLeftMidrange
Connect to Aftermarket amplier
or passive crossover.
  • Page 1 1
  • Page 2 2

PAC APH-CH01 User manual

APH-CH01
PAC
Brand
PAC
Model
APH-CH01
Category
Car speakers
Type
User manual

PAC APH-CH01 simplifies speaker wire connections when adding aftermarket amplifiers to select Chrysler, Dodge, Jeep, and Ram vehicles with factory amplified sound systems, eliminating the need to cut or modify the original wiring. Each wire pair is labeled for easy identification. It features pass-through connections for CAN +, CAN -, left and right front and rear inputs, and constant 12 volts. The harness connects to the factory amplifier's 22-pin and 16-pin connectors.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents