Westbrass D206P-12 Installation guide

Westbrass
Brand
Westbrass
Model
D206P-12
Type
Installation guide

This manual is also suitable for

Westbrass D206P-12 is a shower drain assembly that is designed to fit 2-inch drain pipes. It comes with a tool to help you tighten the compression nut, a locking mechanism, and a rubber seal. To install the drain, remove the strainer, disassemble the locknut and gaskets, apply a bead of silicone sealant to the drain hole, insert the drain assembly, and replace the rubber washer, fiber washer, and locknut. Hand tighten the locknut and remove any excess sealant. The drain is made of durable materials and is easy to install. It is a great choice for a new shower or for replacing an old drain.

Westbrass D206P-12 is a shower drain assembly that is designed to fit 2-inch drain pipes. It comes with a tool to help you tighten the compression nut, a locking mechanism, and a rubber seal. To install the drain, remove the strainer, disassemble the locknut and gaskets, apply a bead of silicone sealant to the drain hole, insert the drain assembly, and replace the rubber washer, fiber washer, and locknut. Hand tighten the locknut and remove any excess sealant. The drain is made of durable materials and is easy to install. It is a great choice for a new shower or for replacing an old drain.

STRAINER
DRAIN
ASSEMBLY
SILICONE
SEALANT
SHOWER BASE
RUBBER WASHER
FIBER WASHER
NUT
APPLY LUBRICANT
Remove the stainless steel strainer from the drain
assembly. Disassemble the locknut and two gaskets
from the back of the drain assembly. Apply a 1/4" bead
of caulking (silicone) to the drain hole and insert the drain
assembly. Replace the rubber washer, fiber washer,
and lock nut in that order. Hand tighten the locknut.
Remove excess sealant from finished side.
TIGHTEN SEALING NUT
TOOL
(INCLUDED)
Remove the tool, locking mechanism and rubber seal
from the inside of the shower drain. Lubricate the seal
with common household liquid soap and slide it over
the 2” drain pipe. With a large screwdriver and the tool
provided, tighten the compression nut to seal the drain
pipe connection. After the drain is fully installed check
for proper drainage and inspect for leaks.
Fine Decorative Plumbing Since 1935
WESTBRASS
2429 E Olympic Blvd., Los Angeles, CA 90021
213-627-8441 | www.westbrass.com | inf[email protected]
STRAINER
DRAIN
ASSEMBLY
SILICONE
SEALANT
SHOWER BASE
RUBBER WASHER
FIBER WASHER
NUT
APPLY LUBRICANT
Remove the stainless steel strainer from the drain
assembly. Disassemble the locknut and two gaskets
from the back of the drain assembly. Apply a 1/4" bead
of caulking (silicone) to the drain hole and insert the drain
assembly. Replace the rubber washer, fiber washer,
and lock nut in that order. Hand tighten the locknut.
Remove excess sealant from finished side.
TIGHTEN SEALING NUT
TOOL
(INCLUDED)
Remove the tool, locking mechanism and rubber seal
from the inside of the shower drain. Lubricate the seal
with common household liquid soap and slide it over
the 2” drain pipe. With a large screwdriver and the tool
provided, tighten the compression nut to seal the drain
pipe connection. After the drain is fully installed check
for proper drainage and inspect for leaks.
Fine Decorative Plumbing Since 1935
WESTBRASS
2429 E Olympic Blvd., Los Angeles, CA 90021
213-627-8441 | www.westbrass.com | inf[email protected]
STRAINER
DRAIN
ASSEMBLY
SILICONE
SEALANT
SHOWER BASE
RUBBER WASHER
FIBER WASHER
NUT
APPLY LUBRICANT
Remove the stainless steel strainer from the drain
assembly. Disassemble the locknut and two gaskets
from the back of the drain assembly. Apply a 1/4" bead
of caulking (silicone) to the drain hole and insert the drain
assembly. Replace the rubber washer, fiber washer,
and lock nut in that order. Hand tighten the locknut.
Remove excess sealant from finished side.
TIGHTEN SEALING NUT
TOOL
(INCLUDED)
Remove the tool, locking mechanism and rubber seal
from the inside of the shower drain. Lubricate the seal
with common household liquid soap and slide it over
the 2” drain pipe. With a large screwdriver and the tool
provided, tighten the compression nut to seal the drain
pipe connection. After the drain is fully installed check
for proper drainage and inspect for leaks.
Fine Decorative Plumbing Since 1935
WESTBRASS
2429 E Olympic Blvd., Los Angeles, CA 90021
213-627-8441 | www.westbrass.com | inf[email protected]
  • Page 1 1

Westbrass D206P-12 Installation guide

Westbrass
Brand
Westbrass
Model
D206P-12
Type
Installation guide
This manual is also suitable for

Westbrass D206P-12 is a shower drain assembly that is designed to fit 2-inch drain pipes. It comes with a tool to help you tighten the compression nut, a locking mechanism, and a rubber seal. To install the drain, remove the strainer, disassemble the locknut and gaskets, apply a bead of silicone sealant to the drain hole, insert the drain assembly, and replace the rubber washer, fiber washer, and locknut. Hand tighten the locknut and remove any excess sealant. The drain is made of durable materials and is easy to install. It is a great choice for a new shower or for replacing an old drain.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents