Toro Groundsmaster 4700-D Rotary Mower User manual

Category
Lawnmowers
Type
User manual

This manual is also suitable for

FormNo.3434-499RevB
Groundsmaster
®
4500-Dand
4700-DRotaryMower
ModelNo.30881—SerialNo.403450001andUp
ModelNo.30882—SerialNo.403450001andUp
Registeratwww.Toro.com.
OriginalInstructions(EN)
*3434-499*
ThisproductcomplieswithallrelevantEuropean
directives;fordetails,pleaseseetheseparateproduct
specicDeclarationofConformity(DOC)sheet.
ItisaviolationofCaliforniaPublicResourceCode
Section4442or4443touseoroperatetheengineon
anyforest-covered,brush-covered,orgrass-covered
landunlesstheengineisequippedwithaspark
arrester,asdenedinSection4442,maintainedin
effectiveworkingorderortheengineisconstructed,
equipped,andmaintainedforthepreventionofre.
Theenclosedengineowner'smanualissupplied
forinformationregardingtheUSEnvironmental
ProtectionAgency(EPA)andtheCaliforniaEmission
ControlRegulationofemissionsystems,maintenance,
andwarranty.Replacementsmaybeorderedthrough
theenginemanufacturer.
WARNING
CALIFORNIA
Proposition65Warning
Dieselengineexhaustandsomeofits
constituentsareknowntotheStateof
Californiatocausecancer,birthdefects,
andotherreproductiveharm.
Batteryposts,terminals,andrelated
accessoriescontainleadandlead
compounds,chemicalsknownto
theStateofCaliforniatocause
cancerandreproductiveharm.Wash
handsafterhandling.
Useofthisproductmaycauseexposure
tochemicalsknowntotheStateof
Californiatocausecancer,birthdefects,
orotherreproductiveharm.
Introduction
Thismachineisaride-on,rotary-bladelawnmower
intendedtobeusedbyprofessional,hiredoperators
incommercialapplications.Itisprimarilydesigned
forcuttinggrassonwell-maintainedlawnsinparks,
sportselds,andoncommercialgrounds.Usingthis
productforpurposesotherthanitsintendedusecould
provedangeroustoyouandbystanders.
Readthisinformationcarefullytolearnhowtooperate
andmaintainyourproductproperlyandtoavoid
injuryandproductdamage.Youareresponsiblefor
operatingtheproductproperlyandsafely.
Visitwww.Toro.comforproductsafetyandoperation
trainingmaterials,accessoryinformation,helpnding
adealer,ortoregisteryourproduct.
Wheneveryouneedservice,genuineToroparts,or
additionalinformation,contactanAuthorizedService
DealerorToroCustomerServiceandhavethemodel
andserialnumbersofyourproductready.Figure1
identiesthelocationofthemodelandserialnumbers
ontheproduct.Writethenumbersinthespace
provided.
g036837
Figure1
1.Modelandserialnumberlocation
ModelNo.
SerialNo.
Thismanualidentiespotentialhazardsandhas
safetymessagesidentiedbythesafety-alertsymbol
(Figure2),whichsignalsahazardthatmaycause
seriousinjuryordeathifyoudonotfollowthe
recommendedprecautions.
g000502
Figure2
1.Safety-alertsymbol.
Thismanualuses2wordstohighlightinformation.
Importantcallsattentiontospecialmechanical
informationandNoteemphasizesgeneralinformation
worthyofspecialattention.
©2020—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
2
Contactusatwww.Toro.com.
PrintedintheUSA
AllRightsReserved
Contents
Safety.......................................................................4
GeneralSafety...................................................4
Engine-EmissionCertication.............................4
SafetyandInstructionalDecals..........................5
Setup.......................................................................11
1InstallingtheDecals(CEMachines
Only)..............................................................11
2InstallingtheHoodLatch.................................11
3AdjustingtheRollerScraper...........................13
4InstallingtheMulchingBafe..........................14
5PreparingtheMachine...................................14
ProductOverview...................................................15
Controls...........................................................15
Specications..................................................23
MachineSpecications.....................................24
CuttingUnitSpecications................................24
Attachments/Accessories.................................24
BeforeOperation.................................................25
BeforeOperationSafety...................................25
CheckingtheEngine-OilLevel..........................25
CheckingtheCoolingSystem...........................25
CheckingtheHydraulicSystem........................25
DrainingtheWaterSeparator...........................25
CheckingtheRearAxleandGearboxfor
Leaks............................................................25
FillingtheFuelTank..........................................26
CheckingtheTirePressure...............................27
CheckingtheTorqueoftheWheelLug
Nuts..............................................................27
AdjustingtheRollBar.......................................28
AdjustingtheHeightofCut...............................29
CheckingtheInterlockSwitches.......................29
CheckingtheBlade-StoppingTime...................30
SelectingaBlade..............................................30
ChoosingAccessories......................................31
DuringOperation.................................................32
DuringOperationSafety...................................32
StartingtheEngine...........................................33
ShuttingOfftheEngine.....................................33
CuttingGrasswiththeMachine........................33
DieselParticulateFilterRegeneration...............34
UnderstandingtheOperatingCharacteristics
oftheMachine..............................................47
OperatingtheEngine-CoolingFan....................47
UsingCruiseControl.........................................48
UsingtheTransportLatches.............................48
OperatingTips.................................................48
AfterOperation....................................................50
GeneralSafety.................................................50
UsingtheCutting-UnitStorageLanyard............50
HaulingtheMachine.........................................51
PushingorTowingtheMachine........................51
LocatingtheTie-DownPoints...........................52
Maintenance...........................................................53
MaintenanceSafety..........................................53
RecommendedMaintenanceSchedule(s)...........53
DailyMaintenanceChecklist.............................54
Pre-MaintenanceProcedures..............................55
LiftingtheMachine...........................................55
OpeningtheHood............................................56
AccessingtheHydraulicLift
Compartment................................................57
Lubrication..........................................................57
GreasingtheBearingsandBushings................57
EngineMaintenance...........................................59
EngineSafety...................................................59
ServicingtheAirCleaner..................................59
ServicingtheEngineOil....................................60
ServicingtheDiesel-OxidationCatalyst
(DOC)andtheSootFilter..............................61
FuelSystemMaintenance...................................62
DrainingtheFuelT ank......................................62
InspectingtheFuelLinesand
Connections..................................................62
ServicingtheFuel-WaterSeparator..................62
ServicingtheFuelFilter....................................63
CleaningtheFuel-PickupTubeScreen.............64
PrimingtheFuelSystem...................................64
ElectricalSystemMaintenance...........................65
ElectricalSystemSafety...................................65
CheckingtheBatteryCondition.........................65
ChargingandConnectingtheBattery...............65
LocatingtheFuses...........................................66
DriveSystemMaintenance..................................67
CheckingforEnd-PlayinthePlanetary
Drives............................................................67
CheckingthePlanetaryGear-Drive
Lubricant.......................................................68
ChangingthePlanetary-Gear-Drive
Oil.................................................................68
CheckingtheRearAxleandGearboxfor
Leaks............................................................70
CheckingtheRear-AxleLubricant....................70
ChangingtheRear-AxleLubricant....................70
CheckingtheRear-Axle-Gearbox
Lubricant.......................................................71
CheckingtheRearWheelT oe-In......................71
CoolingSystemMaintenance..............................72
CoolingSystemSafety.....................................72
CheckingtheCoolingSystem...........................72
CleaningtheCoolingSystem............................74
BrakeMaintenance.............................................75
AdjustingtheServiceBrakes............................75
BeltMaintenance................................................75
ServicingtheAlternatorBelt.............................75
HydraulicSystemMaintenance...........................76
HydraulicSystemSafety...................................76
ServicingtheHydraulicFluid............................76
CheckingtheHydraulicLinesand
Hoses............................................................78
CuttingUnitMaintenance.....................................79
RemovingtheCuttingUnits..............................79
InstallingtheCuttingUnits................................79
ServicingtheFrontRoller.................................79
3
BladeMaintenance..............................................80
BladeSafety.....................................................80
ServicingtheBladePlane.................................80
RemovingandInstallingtheCutting-Unit
Blade(s)........................................................81
InspectingandSharpeningtheCuttingUnit
Blade(s)........................................................82
Storage...................................................................83
StorageSafety..................................................83
PreparingtheMachineforStorage...................83
PreparingaCuttingUnit....................................84
Safety
Thismachinehasbeendesignedinaccordance
withENISO5395(whenyoucompletethesetup
procedures)andANSIB71.4-2017.
GeneralSafety
Thisproductiscapableofamputatinghandsand
feetandofthrowingobjects.Alwaysfollowallsafety
instructionstoavoidseriouspersonalinjury.
Readandunderstandthecontentsofthis
Operator’sManualbeforestartingtheengine.
Useyourfullattentionwhileoperatingthe
machine.Donotengageinanyactivitythat
causesdistractions;otherwise,injuryorproperty
damagemayoccur.
Donotoperatethemachinewithoutallguards
andothersafetyprotectivedevicesinplaceand
functioningproperlyonthemachine.
Keepyourhandsandfeetawayfromrotating
parts.Keepclearofthedischargeopening.
Keepbystandersandchildrenoutoftheoperating
area.Neverallowchildrentooperatethemachine.
Shutofftheengine,removethekey(ifequipped),
andwaitforallmovementtostopbeforeyouleave
theoperatorsposition,Allowthemachinetocool
beforeadjusting,servicing,cleaning,orstoringit.
Improperlyusingormaintainingthismachinecan
resultininjury.Toreducethepotentialforinjury,
complywiththesesafetyinstructionsandalways
payattentiontothesafety-alertsymbol
,which
meansCaution,Warning,orDanger—personalsafety
instruction.Failuretocomplywiththeseinstructions
mayresultinpersonalinjuryordeath.
Engine-Emission
Certication
TheengineinthismachineisEPATier4FinalandEU
StageVemissionscompliant.
4
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea
ofpotentialdanger.Replaceanydecalthatisdamagedormissing.
decal93-7818
93-7818
1.Warning—readtheOperator'sManualforinstructionson
torquingthebladebolt/nutto115to149N∙m(85to110
ft-lb).
decal98-4387
98-4387
1.Warning—wearhearingprotection.
decal106-6754
106-6754
1.Warning—donottouchthehotsurface.
2.Cutting/dismembermenthazard,fanandentanglement
hazard,belt—stayawayfrommovingparts.
decal106-6755
106-6755
1.Enginecoolantunder
pressure.
3.Warning—donottouchthe
hotsurface.
2.Explosionhazard—read
theOperator'sManual.
4.Warning—readthe
Operator'sManual.
decal107-1972
107-1972
1.Thrownobjecthazard—useastandardbladewhenthe
mulchbafeisinstalled;donotuseahigh-liftbladewhen
themulchbafeisinstalled.
decal112-5297
112-5297
1.Warning—readtheOperator'sManual;donotoperatethe
machineunlessyouaretrained.
2.Warning—readtheOperator'sManualbeforetowingthe
machine.
3.Tippinghazard—turnatlowspeeds;donotturnathigh
speeds;lowerthecuttingunitwhendrivingdownslopes;
usearolloverprotectionsystemandweartheseatbelt.
4.Warning—donotparkthemachineonslopes;engagethe
parkingbrake,lowerthecuttingunits,shutofftheengine,
andremovethekeybeforeleavingthemachine.
5.Thrownobjecthazard—keepbystandersaway.
6.Entanglementhazard,belt—stayawayfrommovingparts;
keepallguardsandshieldsinplace.
5
decal117-4763
117-4763
1.Toengagetheparking
brake,securethebrake
pedalswiththelockingpin,
presstheparking-brake
pedalsandengagethetoe
pedal.
2.Todisengagetheparking
brake,disengagethe
lockingpinandreleasethe
pedals.
decal117-4764
117-4764
1.Thrownobjecthazard—keepbystandersaway.
2.Cuttinghazardofhand,mowerblade—stayawayfrom
movingparts;keepallguardsandshieldsinplace.
3.Cuttinghazardoffoot,mowerblade—stayawayfrom
movingparts;keepallguardsandshieldsinplace.
decal117-4765
117-4765
1.ReadtheOperator'sManual.
2.Donotusestartingaids.
decal117-4766
117-4766
1.Cutting/dismembermenthazard;fan—stayawayfrom
movingparts,keepallguardsandshieldsinplace.
decal120-4159
120-4159
1.Off
8.High
2.Lights9.Tractiondrive
3.On
10.Low
4.Light-switchlocation
11.Powertakeoff(PTO)
5.Fast
12.Lower,leftcuttingunit
6.Variable-speedadjustment13.Lower,centercuttingunits
7.Slow
14.Lower,rightcuttingunit
6
decal120-8947
120-8947
1.Warning—readthe
Operator’sManual.
4.Iftherollbarisraised,
weartheseatbelt.
2.Thereisnorollover
protectionwhentheroll
barisdown.
5.Iftherollbarislowered,
donotweartheseatbelt.
3.Thereisrolloverprotection
whentherollbarisup.
6.Driveslowlywhenturning.
decal121-3884
121-3884
1.Engine—stop3.Engine—start
2.Engine—preheat
decal121-3887
121-3887
1.ReadtheOperatorsManual.
decal136-2931
136-2931
ForGroundsmaster4500Only
1.Raisethedecks.3.Disengagethecruise
control.
2.Setthecruisecontrol.
decal127-3700
127-3700
ForGroundsmaster4700Only
1.Raisetheleftcuttingunit.4.Setthecruisecontrol.
2.Raisethecentercutting
units.
5.Disengagethecruise
control.
3.Raisetherightcuttingunit.
7
decal125-4605
125-4605
1.Powerseat(10A)6.Powersupplied(10A)
2.Worklight(10A)7.GM4700controller(2A)
3.Engine(10A)8.Powersupplied(7.5A)
4.Powerport(10A)9.GM4500controller(2A)
5.Infocenter(2A)10.Cab(60A)
decalbatterysymbols
BatterySymbols
Someorallofthesesymbolsareonyourbattery.
1.Explosionhazard6.Keepbystandersaway
fromthebattery.
2.Nore,opename,or
smoking
7.Weareyeprotection;
explosivegasescan
causeblindnessandother
injuries.
3.Causticliquid/chemical
burnhazard
8.Batteryacidcancause
blindnessorsevereburns.
4.Weareyeprotection.9.Flusheyesimmediately
withwaterandgetmedical
helpfast.
5.ReadtheOperator's
Manual.
10.Containslead;donot
discard
decal133-8062
133-8062
8
decal121-3627
121-3627
1.Height-of-cutsettings
AfxoverPartNo.112-5297forCE*for4500seriesmachines
decal127-6447
127-6447
Note:Thismachinecomplieswiththeindustrystandardstabilitytestinthestaticlateralandlongitudinaltestswiththemaximum
recommendedslopeindicatedonthedecal.ReviewtheinstructionsforoperatingthemachineonslopesintheOperatorsManualas
wellastheconditionsinwhichyouwouldoperatethemachinetodeterminewhetheryoucanoperatethemachineintheconditionson
thatdayandatthatsite.Changesintheterraincanresultinachangeinslopeoperationforthemachine.
1.Warning—readthe
Operator’sManual;all
operatorsshouldbetrained
beforeoperatingthe
machine.
3.Tippinghazard—donot
driveonslopesgreaterthan
16°.
5.Warning—donotparkon
slopes;engagetheparking
brake,lowerthecutting
units,shutofftheengine,
andremovethekeybefore
leavingthemachine.
7.Entanglementhazard,
belt—stayawayfrom
movingparts;keepall
guardsandshieldsinplace.
2.Warning—readthe
Operator’sManualfor
towinginformation.
4.Keepthecuttingunits
loweredwhiledrivingdown
slopes;alwaysweara
seatbeltwhenoperatingthe
machine.
6.Thrownobject
hazard—keepbystanders
away.
9
AfxoverPartNo.112-5297forCE*for4700seriesmachines
decal127-6448
127-6448
Note:Thismachinecomplieswiththeindustrystandardstabilitytestinthestaticlateralandlongitudinaltestswiththemaximum
recommendedslopeindicatedonthedecal.ReviewtheinstructionsforoperatingthemachineonslopesintheOperatorsManualas
wellastheconditionsinwhichyouwouldoperatethemachinetodeterminewhetheryoucanoperatethemachineintheconditionson
thatdayandatthatsite.Changesintheterraincanresultinachangeinslopeoperationforthemachine.
1.Warning—readthe
Operator’sManual;all
operatorsshouldbetrained
beforeoperatingthe
machine.
3.Tippinghazard—donot
driveonslopesgreaterthan
21°.
5.Warning—donotparkon
slopes;engagetheparking
brake,lowerthecutting
units,shutofftheengine,
andremovethekeybefore
leavingthemachine.
7.Entanglementhazard,
belt—stayawayfrom
movingparts;keepall
guardsandshieldsinplace.
2.Warning—readthe
Operator’sManualfor
towinginformation.
4.Keepthecuttingunits
loweredwhiledrivingdown
slopes;alwaysweara
seatbeltwhenoperatingthe
machine.
6.Thrownobject
hazard—keepbystanders
away.
10
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
Warningdecal1
CEdecal
1
1
Production-yeardecal1
Replacethedecals(CEmachinesonly).
Hood-latchbracket1
Rivet2
Washer1
Screw(1/4x2inches)
1
2
Locknut(1/4inch)
1
Installthehoodlatch(CEmachines
only).
3
Nopartsrequired
Adjusttherollerscraper(optional).
4
Nopartsrequired
Installthemulchingbafe(optional).
5
Nopartsrequired
Preparethemachine.
MediaandAdditionalParts
Description
Qty.
Use
Operator'sManual
1
Reviewbeforeoperatingthemachine.
Engineowner’smanual1
Refertothemanualforadditionalmaintenanceinformation.
DeclarationofConformity
1
Ignitionkeys2
Starttheengine.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
1
InstallingtheDecals(CE
MachinesOnly)
Partsneededforthisprocedure:
1Warningdecal
1
CEdecal
1Production-yeardecal
Procedure
OnmachinesrequiringCEcompliance,replacethe
warningdecal,CEdecal,andtheproduction-year
decal(Figure3).
g279018
Figure3
1.Warningdecal3.Production-yeardecal
2.CEdecal
11
2
InstallingtheHoodLatch
CEMachinesOnly
Partsneededforthisprocedure:
1Hood-latchbracket
2Rivet
1Washer
1
Screw(1/4x2inches)
1
Locknut(1/4inch)
Procedure
1.Unhookthehoodlatchfromthehood-latch
bracket.
2.Removethe2rivetssecuringthehood-latch
brackettothehood(Figure4).
g012628
Figure4
1.Hood-latchbracket2.Rivets
3.Removethehood-latchbracketfromthehood.
4.Whilealigningthemountingholes,positionthe
CElockbracketandthehood-latchbracketonto
thehood(Figure5).
Note:Thelockbracketmustbeagainstthe
hood.Donotremovetheboltandnutfromthe
lock-bracketarm.
g012629
Figure5
1.CElockbracket
2.Boltandnut
5.Alignthewasherswiththeholesontheinsideof
thehood.
6.Rivetthebracketsandthewasherstothehood
(Figure5).
7.Hookthelatchontothehood-latchbracket
(Figure6).
g012630
Figure6
1.Hoodlatch
8.Installtheboltintotheotherarmofthe
hood-latchbrackettolockthelatchinposition
(Figure7).Tightentheboltbutdonottighten
thenut.
12
g012631
Figure7
1.Bolt
3.Armofhood-latchbracket
2.Nut
3
AdjustingtheRoller
Scraper
Optional
NoPartsRequired
Procedure
Theoptionalrearrollerscraperfunctionsbestwhen
thereisanevengapof0.5to1mm(0.02to0.04inch)
betweenthescraperandtheroller.
1.Loosenthegreasettingandthemounting
screw(Figure8).
g011346
Figure8
1.Rollerscraper
3.Greasetting
2.Mountingscrew
2.Slidethescraperupordownuntilyouobtaina
gapof0.5to1mm(0.02to0.04inch)between
therodandtheroller.
3.Tightenthegreasettingandscrewto41N∙m
(30ft-lb)inanalternatingsequence.
13
4
InstallingtheMulching
Bafe
Optional
NoPartsRequired
Procedure
ContactyourauthorizedT orodistributorforthecorrect
mulchingbafe.
1.Thoroughlycleandebrisfromthemountingholes
ontherearwallandleftwallofthechamber.
2.Installthemulchingbafeintherearopening
andsecureitwith5ange-headbolts(Figure9).
g031579
Figure9
1.Mulchingbafe
2.Flange-headbolt
3.Verifythatthemulchingbafedoesnotinterfere
withthetipofthebladeanddoesnotprotrude
insidethesurfaceoftherearchamberwall.
DANGER
Usingthehigh-liftbladewiththe
mulchingbafecouldcausetheblade
tobreak,resultinginpersonalinjuryor
death.
Donotusethehigh-liftbladewiththe
bafe.
5
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface.
2.Lowerthecuttingunits.
3.Engagetheparkingbrake.
4.Shutofftheengineandremovethekey.
5.Checkthetirepressurebeforeuse;referto
CheckingtheTirePressure(page27).
Important:Maintainpressureinalltires
toensureagoodquality-of-cutandproper
machineperformance.Donotunderinate
thetires.
6.Checktherear-axlelubricantlevelbefore
youstarttheengineforthersttime;referto
CheckingtheRear-AxleLubricant(page70).
7.Checktheengine-oillevelbeforestartingthe
engine;refertoCheckingtheEngine-OilLevel
(page60).
8.Checkthehydraulic-uidlevelbeforestarting
theengine;refertoCheckingtheHydraulic-Fluid
Level(page76).
9.Checkthecoolingsystembeforestartingthe
engine;refertoCheckingtheCoolingSystem
(page72).
10.Greasethemachinebeforeuse;referto
GreasingtheBearingsandBushings(page57).
Failuretoproperlygreasethemachinewillresult
inprematurefailureofcriticalparts.
14
ProductOverview
Controls
g009979
Figure10
1.Brakepedal4.Tractionpedal
2.Pedal-lockinglatch5.Tilt-steeringpedal
3.Parking-brakepedal
TractionPedal
Thetractionpedal(Figure10)controlsforwardand
reverseoperation.Pressthetopofthepedaltomove
forwardandthebottomtomovebackward.
Tostopthemachine,use1ofthefollowing
procedures:
Reduceyourfootpressureonthetractionpedal
andallowittoreturntothecenterposition.The
machinedynamicallybrakestoasmoothstop.
Taporholdthereversepedalbriey.Thisstops
themachinefasterthandynamicbraking.
Note:Inemergencybrakingsituations,pressthe
servicebrakepedalsinadditiontousingthereverse
pedalasstatedabove.Thisisthequickestwayto
stopthemachine.
BrakePedals
Thereare2footpedalsthatoperateindividualwheel
brakesforturningassistance,parking,andtoaidin
betterside-hilltraction.Alatchconnectsthepedals
forparking-brakeoperationandtransport(Figure10).
Pedal-LockingLatch
Thepedal-lockinglatchconnectsthepedalstogether
toengagetheparkingbrake(Figure10).
Tilt-SteeringPedal
Totiltthesteeringwheeltowardyou,pressthefoot
pedaldown,pullthesteeringtowertowardyouto
themostcomfortableposition,andreleasethepedal
(Figure10).T omovethesteeringwheelawayfrom
you,pressthefootpedalandreleaseitwhenthe
steeringwheelreachesthedesiredoperatingposition.
Parking-BrakePedal
Toengagetheparkingbrake,(Figure10)connectthe
pedalstogetherwiththepedal-lockinglatchandpush
downontherightbrakepedalwhileengagingthetoe
pedal.Toreleasetheparkingbrake,press1ofthe
brakepedalsuntiltheparkingbrakelatchretracts.
KeySwitch
Thekeyswitch(Figure11)has3positions:OFF,
ON/PREHEAT,andSTART.
g208967
Figure11
1.Liftswitches
(Groundsmaster4700
machineonly)
5.InfoCenter
2.Liftswitch(Groundsmaster
4500and4700machines)
6.Hi-Lospeedcontrol
3.PTOswitch
7.Engine-speedswitch
4.Keyswitch8.Lightswitch
g028454
Figure12
1.Power-pointswitch
2.Cruise-controlswitch
15
Engine-SpeedSwitch
Theengine-speedswitch(Figure11)has2modesto
changetheenginespeed.T aptheswitchtoincrease
ordecreasetheenginespeedin100rpmincrements.
HolddowntheswitchtoautomaticallymovetoHigh
orLowidle,dependingonwhichendoftheswitch
youpress.
PTOSwitch
ThePTOswitchhas2positions:OUT(START)and
IN(STOP).PullthePTObuttonouttoengagethe
cutting-unitblades.Pushthebuttonintodisengage
thecutting-unitblades(Figure11).
High-LowSpeedControl
Theswitch(Figure11)allowsthespeedrangeto
increasefortransportingthemachine.T oswitch
betweentheHighandLowspeedranges,raisethe
cuttingunits,disengagethePTOandthecruise
control,putthetractionpedalintotheNEUTRAL
position,andmovethemachineataslowspeed.
Note:Thecuttingunitsdonotoperateand/orcannot
beloweredfromthetransportpositionwhenthe
switchisinthehighrange.
Cruise-ControlSwitch
Thecruise-controlswitchlocksinthepedalposition
tomaintainthedesiredgroundspeed(Figure11).
Pressingtherearoftheswitchturnsoffthecruise
control,themiddlepositionoftheswitchenablesthe
cruise-controlfunction,andthefrontoftheswitchsets
thedesiredgroundspeed.
Note:Pressingeitherbrakepedalormovingthe
tractionpedalintothereversepositionfor1second
alsodisengagesthecruisecontrol.
LiftSwitches
Theliftswitchesraiseandlowerthecuttingunits
(Figure11).Presstheswitchesforwardtolowerthe
cuttingunitsandrearwardtoraisethecuttingunits.
Whenstartingthemachine,withthecuttingunitsin
thedownposition,presstheliftswitchdowntoallow
thecuttingunitstooatandmow.
Note:Thecuttingunitsdonotlowerwhileinthe
high-speedrangeandtheydonotraiseorlowerifyou
areoutoftheseatwhiletheengineisrunning.Also,
thecuttingunitslowerwiththekeyintheONposition
andyouareintheseat.
LightSwitch
Presstheloweredgeoftheswitch(Figure11)toturn
onthelights.Presstheupperedgeoftheswitchto
turnoffthelights.
PowerPoint
Usethepowerpoint(Figure13)topoweroptional12
Velectricalaccessories.
g036845
Figure13
1.Powerpoint2.Bagholder
BagHolder
Usethebagholderforstorage(Figure13).
SeatAdjustments
Seat-AdjustmentLever
Movetheseatadjustmentleveronthesideofthe
seatoutward,slidetheseattothedesiredposition,
andreleasethelevertolocktheseatintoposition
(Figure14).
16
g024916
Figure14
1.Weightgauge
4.Seat-backadjustment
lever
2.Weightadjustmentlever5.Armrestadjustmentknob
3.Seatadjustmentlever
ArmrestAdjustmentKnob
Rotatetheknobtoadjustthearmrestangle(Figure
14).
Seat-BackAdjustmentLever
Movethelevertoadjusttheseat-backangle(Figure
14).
WeightGauge
Theweightgaugeindicateswhentheseatisadjusted
totheweightoftheoperator(Figure14).Adjustthe
heightbypositioningthesuspensionwithintherange
ofthegreenregion.
WeightAdjustmentLever
Usethislevertoadjusttheseattoyourweight(Figure
14).Pulltheleveruptoincreasetheairpressureand
pushtheleverdowntodecreasetheairpressure.The
properadjustmentiscorrectwhentheweightgaugeis
inthegreenregion.
UsingtheInfoCenterLCDDisplay
TheInfoCenterLCDdisplayshowsinformationabout
yourmachine,suchastheoperatingstatus,various
diagnosticsandotherinformationaboutthemachine
(Figure15).Thereisasplashscreenandmain
informationscreenoftheInfoCenter.Youcanswitch
betweenthesplashscreenandmaininformation
screenatanytimebypressinganyoftheInfoCenter
buttonsandthenselectingtheappropriatedirectional
arrow.
g020650
Figure15
1.Indicatorlight3.Middlebutton
2.Rightbutton
4.Leftbutton
LeftButton,MenuAccess/BackButton—pressthis
buttontoaccesstheInfoCentermenus.Youcan
useittoexitanymenuthatyouarecurrentlyusing.
MiddleButton—usethisbuttontoscrolldown
menus.
RightButton—usethisbuttontoopenamenu
wherearightarrowindicatesadditionalcontent.
Beeper—activatedwhenloweringthecuttingunits
orforadvisoriesandfaults.
Note:Thepurposeofeachbuttonmaychange
dependingonwhatisrequiredatthetime.Each
buttonislabeledwithanicondisplayingitscurrent
function.
17
InfoCenterIconDescription
SERVICEDUE
Indicateswhenscheduledservice
shouldbeperformed
Hoursremaininguntilservice
Resettheservicehours
Thestatusoftheenginerpm
Infoicon
Maximumtractionspeedsetting
Fast
Slow
Thefanisreversed
DPFregenerationisrequired
Theair-intakeheaterisactive
Raisetheleftcuttingunit.
Raisethecentercuttingunit
Raisetherightcuttingunit
Theoperatormustsitintheseat
Theparkingbrakeisengaged
Therangeishigh
Neutral
IdentiestherangeasLow
Coolanttemperature(°Cor°F)
Temperature(hot)
TractionorTractionPedal
Notallowed
InfoCenterIconDescription(cont'd.)
Starttheengine.
ThePTOison.
Thecruisecontrolison.
Shutofftheengine
Engine
Keyswitch
Cuttingunitsarelowering
Cuttingunitsareraising
PINcode
Hydraulicuidtemperature
CANbus
InfoCenter
Badorfailed
Center
Right
Left
Bulb
OutputofTECcontrollerorcontrol
wireinharness
Overtheallowedrange
Undertheallowedrange
/
Outofrange
Switch
Operatormustreleaseswitch
18
InfoCenterIconDescription(cont'd.)
Operatorshouldchangetoindicated
state
Symbolsareoften
combinedtoform
sentences.Some
examplesareshown
below
Operatorshouldputmachinein
neutral
Enginestartisdenied
Engineshutdown
Enginecoolantistoohot
Hydraulicuidistoohot
DPFashaccumulationnotication.
RefertoServicingtheDiesel
ParticulateFilter(DPF)inthe
maintenancesectionfordetails
Reset-standbyregenerationrequest
Parkedorrecoveryregeneration
request
Aparkedorrecovery-standby
regenerationisprocessing.
Highexhausttemperature
NOxcontroldiagnosismalfunction;
drivethemachinebacktotheshop
andcontactyourauthorizedToro
distributor(softwareversionPand
later).
Thepowertake-offisdisabled.
Sitdownorengageparkingbrake
AccessibleonlybyenteringPIN
19
UsingtheMenus
ToaccesstheInfoCentermenusystem,pressthe
menuaccessbuttonwhileatthemainscreen.This
bringsyoutothemainmenu.Refertothefollowing
tablesforanoverviewoftheoptionsavailablefrom
themenus:
MainMenu—MenuItemDescription
Faults
Containsalistoftherecent
machinefaults;refertothe
ServiceManualformore
information.
ServiceContainsinformationonthe
machinesuchashoursofuse
andothersimilarnumbers
DiagnosticsListsvariousstatesthatthe
machinecurrentlyhas;you
canusethistotroubleshoot
certainissuesasitquicklytells
youwhichmachinecontrols
areonandwhichareoff.
Settings
Allowsyoutocustomizeand
modifycongurationvariables
ontheInfoCenterdisplay
AboutListsthemodelnumber,serial
number,andsoftwareversion
ofyourmachine
Service—MenuItem
Description
Hours
Liststhetotalnumberofhours
thatthemachine,engine,and
fanhavebeenon,aswell
asthenumberofhoursthe
machinehasbeentransported
andoverheated
CountsListsthenumberofstarts,
cuttingunit/PTOcycles,and
fanreversalsthemachinehas
experienced
DPFRegeneration
Thedieselparticulatelter
regenerationoptionandDPF
submenus
InhibitRegenUsetocontrolreset
regeneration
ParkedRegenUsetoinitiateaparked
regeneration
LastRegenListsthenumberhourssince
thelastreset,parked,or
recoveryregeneration
RecoverRegenUsetoinitiatearecovery
regeneration
Diagnostics—MenuItemDescription
LeftCuttingUnit
CenterCuttingUnit
RightCuttingUnit
Traction
HI/LORange
PTO
Engine
Cruise
RefertotheServiceManual
oryourauthorizedT oro
distributorformoreinformation
ontheEngineRunmenuand
theinformationcontained
there.
Settings—MenuItem
Description
Units
Controlstheunitsusedonthe
InfoCenter(EnglishorMetric)
Language
Controlsthelanguageused
ontheInfoCenter*
LCDBacklightControlsthebrightnessofthe
LCDdisplay
LCDContrastControlsthecontrastofthe
LCDdisplay
ProtectedMenusAllowsapersonauthorized
byyourcompanywiththe
PINcodetoaccessprotected
menus.
ProtectSettings
Allowstheabilitytochange
thesettingsintheprotected
settings
AutoIdle
Controlstheamountoftime
allowedbeforeidlingthe
enginewhenthemachineis
notinuse
MowSpeed
Controlsthemaximumspeed
whileinmow(lowrange)
Trans.Speed
Controlsthemaximumspeed
whileintransport(highrange)
SmartPower
TurnsSmartPoweronandoff
Counterbalance
Controlstheamountof
counterbalanceappliedbythe
cuttingunits
Turnaround
TurnsTurnaroundonandoff
*Only"operator-faced"textistranslated.Faults,
Service,andDiagnosticsscreensare"service-faced.”
Titlesareintheselectedlanguage,butmenuitems
areinEnglish.
ProtectedunderProtectedMenus—accessibleonly
byenteringPIN
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88

Toro Groundsmaster 4700-D Rotary Mower User manual

Category
Lawnmowers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI