MULTIPLEX Flavor Magic Touchpad Kit Installation guide

Brand: MULTIPLEX

Model: Flavor Magic Touchpad Kit

Type: Installation guide

1 of 2

020001429 REV0

02/06/07

If you have any questions concerning this bulletin, please contact Technical Service at (800)367-4233

FLAVOR MAGIC TOUCH PAD REPAIR KIT

Used where Flavoring is Tracking in front of Drainpan

1. Remove medallion from merchandiser on ice dispenser

2. Remove lamps over rocking chutes or in work area

3. Disconnect 24 volt power supply from Flavor Magic circuit

board. Do not reconnect until wire harnesses are reattached

to touch pad and LED.

4. Disconnect wire harnesses from touch pad (4 pin polar-

ized) and from LED (2 pin)

5. Carefully remove touch pad assembly retaining pin (if used).

6. Carefully remove touch pad assembly from merchandiser

medallion channel.

7. Separate back of touch pad assembly from front. Pull out-

ward on front cover while holding back cover. This will allow

the parts to unsnap from each other.

8. Remove syrup tubes and retainer from touch pad assembly.

9. If medallion channel has been bent out to correct syrup

flow problems, bend back as closely as possible to original

position.

10. New cover has a built in clip which will attach over the me-

dallion channel. It may be necessary to adjust the opening

of the clip to fit it on to the channel. Make sure when any

adjustments are made, the clip fits tightly over the channel.

11. Make certain that when the touch pad buttons are pushed,

the rocking chute does not dispense ice. It may be neces-

sary to adjust the side tabs on the stainless steel plate chute

to assure this. The tabs contact the rocking chute supports

and limit the movement of the stainless cover.

12. Route syrup lines behind cover assembly and into back of

cover.

13. Route syrup lines into the back of back touch pad assem-

bly. Push syrup lines into retainer until they bottom out. Holes

in retainer are tapered to hold lines securely but they can

be pulled out.

IMPORTANT NOTE: PRIOR TO WORKING ON UNIT, DISCONNECT ELECTRICAL

POWER. THIS WILL SAFELY SHUT OFF POWER TO THE DISPENSE SWITCH TO

ELIMINATE NUISANCE ICE DISPENSES WHILE WORKING IN THE ICE CHUTE AREA

14. Twist on clear plastic nozzle. Retainer tubes should pro-

trude slightly from the bottom of the nozzle.

15. Mount LED into tab on back of touch pad assembly.

16. Route ribbon connector from touch pad through slot in back

of cover assembly of touch pad assembly.

17. Route both electrical connectors up into merchandiser and

connect to appropriate connectors on harness from control

circuit board. Observe polarity. The touch pad pin arrange-

ment has a pin gap on the male side and a blocked opening

on the female side. The LED pin male side will can only be

connected to the female side one way due to connector

geometry.

18. Attach front touch pad assembly to the back touch pad as-

sembly. The plastic parts must be properly aligned. Make

sure the parts are completely snapped together and do not

separate easily. Make sure stainless clip is pushed down

onto the flange on the front of the merchandiser and the

touch pad assembly is centered about the rocking chute.

19. Slide retainer into left side of cover assembly. There is a

unique retainer for the MDH-302 and one for the MDH-402.

(

See Page 2

)

20. Position the retainer so the syrup lines and wires fit into the

center cut out portion of the retainer.

21. Move the retainer toward the merchandiser until the two pin

holes are observed. Place the pin in the holes with the bail

pointed outward and push all the way down to lock the re-

tainer in place.

22. Reconnect power to ice dispenser. Check to assure ice chute

will properly dispense ice when pushed in.

24. Reconnect 24 volt power to circuit board.

2 of 2

020001429 REV0

02/06/07

If you have any questions concerning this bulletin, please contact Technical Service at (800)367-4233

FLAVOR MAGIC TOUCH PAD REPAIR KIT

Used where Flavoring is Tracking in front of Drainpan

25. When display moves to “- - - -”, test each flavor position.

MAKE SURE SYRUP STREAM IS DIRECTED TO THE

CENTER OF THE DRAIN PAN UNDER THE ROCKING

CHUTE AREA. IF IT DOES NOT, TOUCH PAD MOUNT-

ING WILL NEED TO BE ADJUSTED BY BENDING CLIP

TO CHANGE ANGLE OF DISPENSE STREAM.

26. Replace lamps over rocking chute or in work area.

27. Replace medallion.

28. Discard removed parts and clean up syrup, ice, and

water spills.

29. Have store manager sign off on work accomplished.

302 Mounting 402 Mounting

NOTE: Kit Contains both illustration #8 locks for MDH302

(020000806) and for the MDH402 (020000817).

Select the lock appropriate to the dispenser where

the Flavor Magic Module is attached and discard

the other.

MULTIPLEX Flavor Magic Touchpad Kit Installation guide

MULTIPLEX Flavor Magic Touchpad Kit Installation guide

MULTIPLEX Flavor Magic Touchpad Kit Installation guide

Related papers

Other documents