Juniper T640 Installation Instructions Manual

Brand: Juniper

Model: T640

Type: Installation Instructions Manual

This manual is also suitable for

T-CB
T320

Juniper T640 is a high-performance routing platform designed for large-scale service provider networks and data centers. It offers high-density 10GbE, 40GbE, and 100GbE interfaces, as well as advanced features such as MPLS, VPNs, and traffic engineering. With its modular design and redundant components, the T640 provides carrier-class reliability and scalability. Additionally, the T640 supports Junos OS, which offers a wide range of routing protocols, security features, and management tools.

T320 Inter n et Router and T640 Inter net

Routing Node Control Board (T-CB)

Installation Instructions

12 November 2004

Part No: 530-012185-01

Revision 2

This document describes how to remove and replace a Control Board (T-CB) in a

T320 Internet router and a T640 Internet routing node.

Contents

T-CB Description .................................................................... 2

T-CB Components................................................................... 3

Tools and Parts Required........................................................... 4

Replacing a T-CB ................................................................... 4

Removing a T-CB............................................................... 4

Installing a T-CB ............................................................... 5

List of Technical Publications ...................................................... 6

Requesting Support................................................................. 8

Revision History .................................................................... 9

T320 Internet Router and T640 Internet Routing Node Control Board (T-CB ) Installation Instructions

T-CB Description

Each T-CB works with an adjacent Routing Engine to provide control

and monitoring functions for the routing platform (see Figure 1). These

functions include determining Routing Engine mastership; controlling power

and reset for the other routing platform components; monitoring and

controlling fan speed; and monitoring system status.

You can install one or two T-CBs in the routing platform. The T-CBs install

into the upper rear of the chassis in the slots labeled

CB0 and CB1 (referred

to as

T-CB-0 and T-CB-1). If two T-CBs are installed, one functions as the

master T-CB and the other as its backup. If the master fails or is removed,

the backup restarts and becomes the master.

EachT-CBrequiresaRoutingEnginetobeinstalledintheadjacentslot.

T-CB-0

installs above RE0,andT-CB-1 installs below RE1.AT-CBdoesnotfunction

if a Routing Engine is not present in the adjacent slot.

T-CBs are hot-pluggable.

Figure 1: T-CB

g002130

Online/offline

button

Extractor clip

LEDs

Control Board - T

I C

LIN

Extractor clip

M/S and chassis

ID switches

Control

plane ports

NOTE: The T-CB requires JUNOS software Release 7.0 or later.

2 T-CB Description

T-CB Components

Each T-CB consists of the following components:

100-MB Ethernet switch. This switch is used for intermodule communication.

PCI bus to the Routing Engines.

Processor subsy stem (SPMB).

Three LEDs, located on the T-CB faceplate. These indicate the status of the

T-CB. Table 1 describes the functions of the T-CB LEDs.

Online/offline b utton, located on the T-CB faceplate. This button is

nonfunctional.

Two configuration switches, located on the T-CB faceplate.

NOTE: The M/S and CHASSIS ID switches on the T-CB faceplate must always be set to

S and 0 in a standalone routing platform.

If a T640 routing node is connected to a TX Matrix platform, these switches must

be set to

M and the chassis identifier (ID) of the routing node. In this case, both

T-CBs must have t he same chassis ID. For more information, see the TX Matrix

Platform Hardware Guide.

Two RJ-45 ports labeled AUX and CIP on the T-CB faceplate. These ports are not

used in a standalone routing platform. Only the

CIP port is used in a T640

routing node connected to a TX Matrix platform. For more information, see

the TX Matrix Platform Hardware Guide.

Table 1: T-CB LEDs

Label Color State Description

MASTER Blue On steadily T-CB is functioning as the master.

FAIL Amber On steadily T-CB has failed.

On steadily T-CB is online and is functioning normally.OK

Green

Blinking T-CB is pow

ering up, but not online.

T-CB Components 3

T320 Internet Router and T640 Internet Routing Node Control Board (T-CB ) Installation Instructions

Tools and Parts R equired

To replace a T-CB, you need the following tools:

Phillips (+) screwdriver, number 2

ESD wrist strap with cable

Electrostatic bag or antistatic mat

Blank panels to cover any slots not occupied by a component

Replacing a T-CB

The T-CBs are hot-pluggable. If the routing platform contains a redundant host

subsystem, the T-CB an d the Routing Engine are hot-removable and hot-insertable.

Before you replace a T-CB or a Routing Engine, you must take the host subsystem

offline(seetheT320 Internet Router Hardware Guide or the T640 Internet Routing

Node Hardware Guide). To replace a T-CB, use the following procedures:

NOTE: The figures in these procedures show the T640 routing node for reference.

Removing a T-CB on page 4

InstallingaT-CBonpage 5

Removing a T-CB

The routing platform can have one or two T-CBs. They are located in

the upper rear of the chassis in the slots marked

CB0 and CB1.Each

T-CB weighs approximately 5 lb (2.3 kg).

To remove a T-CB, follow this procedure (see Figure 2):

1. Place an electrostatic bag or antistatic mat on a flat, stable surface.

2. At tach an electrostatic discharge (ESD) grounding strap to your bare wrist

and connect the strap to one of the ESD points on the chassis. For more

information about ESD, see the T320 Internet Router Hardware Guide or the

T640 Internet Routing Node Hardware Guide.

3. Check whether the T-CB is functioning as the backup or as the master. If

necessary, take the host subsystem offline as described in the T320 Internet

Router Hardware Guide or the T640 Internet Routing Node Hardware Guide.

4. If applicable, disconnect the cable plugged into the port labeled CIP.

5. Loosen t he captive screws (using a Phillips (+) screwdriver, number 2) on the

ejector handles on both sides of the T-CB faceplate.

4 Removing a T-CB

6. Flip the ejector handles outward to unseat the T-CB.

7. Grasp the ejector handles and slide the T-CB about halfway out of the chassis.

8. Place one hand underneath the T-CB to support it and slide it completely

outofthechassis.

9. PlacetheT-CBontheantistaticmat.

10. If you are not replacing the T-CB now, install a blank panel over the empty slot.

Figure 2: Removing a T-CB

g002187

Installing a T-CB

To install a T-CB, follow this procedure (see Figure 3):

1. At tach an electrostatic discharge (ESD) grounding strap to your bare wrist

and connect the strap to an approved site ESD grounding point. For more

information about ESD, see the T320 Internet Router Hardware Guide or the

T640 Internet Routing Node Hardware Guide.

2. Ensure the ejector handles are not flush with the faceplate. If necessary, loosen

the captive screws and flip the ejector handles outward.

3. Carefully align the sides of the T-CB with the guides inside the chassis.

4. Slide the T-CB into the chassis, carefully ensuring that it is correctly aligned.

5. Grasp both ejector handles and press them inward to seat the T-CB.

6. Tighten the captive screws on the ejector handles, using a Phillips (+)

screwdriver, number 2.

7. If applicable, reconnect the cable previously plugged into the CIP port.

Installing a T-CB 5

T320 Internet Router and T640 Internet Routing Node Control Board (T-CB ) Installation Instructions

8. If power is applied to the T-CB and its corresponding Routing Engine is

functioning normally, the T-CB comes online automatically. To verify that the

T-CB is functioning normally, check the LEDs on its faceplate. The green

OK LED

should light steadily a few minutes after the T-CB is installed. If the

FAIL LED is

lit steadily, remove and install the T-CB again (see “Removing a T-CB” on page

4 and “Installing a T-CB ” on p age 5 ). If the

FAIL LED still lights steadily, the

T-CB is not functioning properly. Cont act your cust omer support representativ e.

To check the status of the T-CB, use the CLI command:

user@host> show chassis environment cb

Figure 3: Reinstalling a T-CB

g002188

List of Technical Publications

Table 2 lists the software and hard ware guides and release notes for Juniper

Networks routing platforms that use the JUNOS Internet software and d escribes

the contents of each book.

Table 2: Juniper Networks Technical Documentation

Book Description

JUNOS for J-series, M-series, and T-series Routing Platforms Configuration Guides

Feature Guide

Provides a detailed explanation and configuration examples for

several of the most complex features in t he JUNOS softwa re.

System Basics

Provides an overview of the JUNOS software and describes how to

install and upgrade the software. This manual also describes how

to configure system management functions and how to configure

the chassis, including user accounts, passwords, and r e dundancy.

6 List of Technical Publications

Book Description

Network Interfaces and Class of Service

Provides an overview of the network interface and class-of-service

functions of the JUNOS software and describes how t o configure

the network interfaces on the router.

MPLS Applications

Provides an overview of traffic engineering concepts and describes

how to configure traffic engineering protocols.

Multicast Protocols

Provides an overview of multicast concepts and describes how to

configure multicast routing protocols.

Network Management

Provides an overview of network management concepts and

describes how to configure various network management features,

such as SNMP, accounting options, and cflowd.

Policy Framework

Provides an overview of policy concepts and describes how to

configure routing policy, firewall filters, and forwarding options.

Routing Protocols

Provides an overview of routing concepts and describes how to

configure routing, routing instances, and unicast routing protocols.

Services Interfaces

Provides an overview of the services interfaces functions of the

JUNOS software and describes how to configure the services

interfaces on the router.

VPNs

Provides a

n overview and describes how to configure Layer 2 and

La y er 3 virtual private networks (VPNs), virtual private LAN service

(VPLS), and Lay er 2 circuits. Pr ovides configuration examples .

JUNOS Refe

renc es

Network and Services Interfaces Command

Reference

Describes the JUNOS Internet software operational mode

commands you use to monitor and troubleshoot network and

services interfaces on Juniper Networks routing platforms.

Protocols , Class of Service, and Sy stem Basics

Command Reference

Describes the JUNOS Internet software operational mode

commands you use to monitor and troubleshoot most aspects of

Juniper Networks routing platforms.

System Log Messages Reference

Describes how to access and interpr et system log messages

generated by JUNOS softwar e modules and provides a reference

page for each message.

JUNOScript API D ocumentation

JUNOScript API Guide

Describes how to use the JUNOScript application programming

interface (API) to monitor and configure Juniper Networks routers.

JUNOScript API Configuration Reference

Provides reference pages for the configuration tags in the

JUNOScript API.

JUNOScript API Operational Reference

Provides reference pages for the operational tags in the JUNOScript

API.

JUNOS Comprehensive Index and Glossar y

Comprehensive Index and Glossary

Provides a complete index of all JUNOS Internet software books

and the JUNOScript API Guide. Also provides a comprehensive

glossary.

Hardware Docum entation

Hardware Guide

Describes how to install, maintain, and troubleshoot routers and

router components. Each platform has its own hardware guide.

PIC Guide

Describes the router Physical Interface Cards (PICs). Each router

platform has its own PIC guide.

List of Technical Publications 7

T320 Internet Router and T 640 Internet Routing Node Control Board (T-CB) Installation Instructions

Book Description

JUNOScope Documentation

JUNOScope Software User Guide

Describes the JUNOScope software graphical user interface (GUI),

how to install and administer the software, and how to use the

software to manage router configuration files and monitor router

operations.

J-series Services Router Documentation

J-series Services Router User Guide

Contains instructions for installing, configuring, and managing a

J-series Services Router. The guide explains how to prepare your

site for installation, unpack and install the hardware, power on the

router, configure secure routing, monitor network operations, and

perform routine maintenance.

Release Notes

JUNOS Internet Softw are Release Notes

Provide a summary of new features for a particular software

release. Software release notes also contain corrections and

updates to published JUNOS and JUNOScript manuals, pro vide

information that might have been omitted from the manuals, and

describe upgrade and downgrade procedures.

Hardware Release Notes

Describe the available documentation for the router platform

and summarize known problems with the hardware and

accompanying software. Each platform has its own release notes.

JUNOScope Software Release Notes

Contain corrections and updates to the published JUNOScope

manual, pro vide information that might have been omitted from

the manual, and describe upgr ade and do wngrade procedures.

J-series Services Router Release Notes

Briefly describe Services Router features, identify known hardw a re

problems, and provide upgr a de and downgrade instructions

Requesting Support

For technical support, open a support case using the Case Manager link at

http://www.juniper.net/support/ or call 1-888-314-JTAC (within the United States) or

1-408-745-9500 (outside the United States).

If you are reporting a hardware or software problem, issue the following command

from the CLI before contacting support:

user@host>request support information | save

filename

To provide a core file to Juniper Networks for analysis, compress the file with

the

gzip utility, rename the file to include your company name, and copy it to

ftp.juniper.net:pub/incoming. Then send the filename, along with software version

information (the output of t he

show version command) and the configuration, to

support@juniper.net.

For documentation issues, fill out the bug report form located at

http://www.juniper.net/techpubs/docbug/docbugreport.html.

8 Requesting S upport

Revision History

12 November 2004—Revision 2. Added JUNOS software requirement, and updated

support section.

12 November 2004—Revision 1.

Juniper Networks, the Juniper N etwor ks logo, NetScreen, NetScreen Technologies, the N etS creen logo, NetScreen-Glo bal Pro, ScreenO S, a n d

GigaScreen are registered trademarks of Juniper Networks, Inc. in the United States and other cou nt ries.

The following are trademarks of Juniper Networks, Inc.: ERX, ESP, E-series, Instant Virtual Extranet, Internet Processor, J2300, J4300, J6300, J-Protect,

J-series,J-Web,JUNOS,JUNOScope,JUNOScript,JUNOSe,M5,M7i,M10,M10i,M20,M40,M40e,M160,M320,M-series,MMD,NetScreen-5GT,

NetScreen-5XP, NetScreen-5X T, NetScreen-25, Net Screen-50, NetS creen-204, NetScreen-208, NetScreen-500, NetScreen-520 0, N et Screen-5400,

NetScreen-IDP 10, NetScreen-IDP 100, NetScreen-IDP 5 00 , NetScreen-Remote Security Clie nt, NetScreen-Remote VPN Client, NetScreen-SA 1000 Series,

NetScreen-SA 3000 Ser ies, NetScreen-SA 5000 Se ries, NetScreen-SA Central Manager, Net Screen S ecure Access, NetScreen-SM 3000, NetScreen-Security

Manag er, NMC-R X , SD X, Stateful Sign atu re, T320, T64 0, T-ser ies, and TX Mat rix. All other t rademar ks, service marks, registered trademarks, or registered

service marks are th e property of their respective owners. All specifications are subject to chan ge without n otice. Junipe r Networks assumes no responsibility

for any ina ccuracies in this docume n t. Juniper N etworks reserves t he right to change, modify, transfer, or otherwise revise this publi cation with outnotice.

Requesting Support 9