Teledyne API T640 User manual

Category
Measuring, testing & control
Type
User manual
User Manual
Model T640
PM Mass Monitor
© TELEDYNE API (TAPI)
9970 CARROLL CANYON ROAD
SAN DIEGO, CALIFORNIA 92131-1106
USA
Toll-free Phone:
800-324-5190
Phone:
+1 858-657-9800
Fax:
+1 858-657-9816
Email:
api-sales@teledyne.com
Website:
http://www.teledyne-api.com/
Copyright 2016-2018 08354B DCN7877
Teledyne Advanced Pollution Instrumentation 29 June 2018
08354B DCN7877 Teledyne API T640 PM Mass Monitor i
NOTICE OF COPYRIGHT
© 2016-2018 Teledyne Advanced Pollution Instrumentation. All rights reserved.
TRADEMARKS
All trademarks, registered trademarks, brand names or product names appearing in
this document are the property of their respective owners and are used herein for
identification purposes only.
08354B DCN7877 Teledyne API T640 PM Mass Monitor ii
SAFETY MESSAGES
Important safety messages are provided throughout this manual for the purpose of avoiding personal
injury or instrument damage. Please read these messages carefully. Each safety message is associated
with a safety alert symbol, and are placed throughout this manual; the safety symbols are also located
inside the instrument. It is imperative that you pay close attention to these messages, the descriptions of
which are as follows:
WARNING: Electrical Shock Hazard
HAZARD: Strong oxidizer
GENERAL WARNING/CAUTION: Read the accompanying message for
specific information.
CAUTION: Hot Surface Warning
Do Not Touch: Touching some parts of the instrument without protection
or proper tools could result in damage to the part(s) and/or the
instrument.
Technician Symbol: All operations marked with this symbol are to be
performed by qualified maintenance personnel only.
Electrical Ground: This symbol inside the instrument marks the central
safety grounding point for the instrument.
CAUTION
This instrument should only be used for the purpose and in the manner described
in this manual. If you use this instrument in a manner other than that for which it
was intended, unpredictable behavior could ensue with possible hazardous
consequences.
NEVER use any TAPI analyzer to sample combustible gas(es)!
For Technical Assistance regarding the use and maintenance of this instrument or any other Teledyne API
product, contact Teledyne API’s Technical Support Department:
Telephone: 800-324-5190
Email: sda_techsupport@teledyne.com
or access any of the service options on our website at http://www.teledyne-api.com/
08354B DCN7877 Teledyne API T640 PM Mass Monitor iii
CONSIGNES DE SÉCURITÉ
Des consignes de sécurité importantes sont fournies tout au long du présent manuel dans le but d’éviter
des blessures corporelles ou d’endommager les instruments. Veuillez lire attentivement ces consignes.
Chaque consigne de sécurité est représentée par un pictogramme d’alerte de sécurité; ces pictogrammes se
retrouvent dans ce manuel et à l’intérieur des instruments. Les symboles correspondent aux consignes
suivantes:
AVERTISSEMENT : Risque de choc électrique
DANGER : Oxydant puissant
AVERTISSEMENT GÉNÉRAL / MISE EN GARDE : Lire la consigne
complémentaire pour des renseignements spécifiques
MISE EN GARDE : Surface chaude
Ne pas toucher : Toucher à certaines parties de l’instrument sans protection ou
sans les outils appropriés pourrait entraîner des dommages aux pièces ou à
l’instrument.
Pictogramme « technicien » : Toutes les opérations portant ce symbole doivent
être effectuées uniquement par du personnel de maintenance qualifié.
Mise à la terre : Ce symbole à l’intérieur de l’instrument détermine le point central
de la mise à la terre sécuritaire de l’instrument.
MISE EN GARDE
Cet instrument doit être utilisé aux fins décrites et de la manière décrite dans ce
manuel. Si vous utilisez cet instrument d’une autre manière que celle pour laquelle il
a été prévu, l’instrument pourrait se comporter de façon imprévisible et entraîner des
conséquences dangereuses.
NE JAMAIS utiliser un analyseur de gaz pour échantillonner des gaz combustibles!
08354B DCN7877 Teledyne API T640 PM Mass Monitor iv
WARRANTY
WARRANTY POLICY (02024J)
Teledyne API (TAPI), a business unit of Teledyne Instruments, Inc., provides that:
Prior to shipment, TAPI equipment is thoroughly inspected and tested. Should
equipment failure occur, TAPI assures its customers that prompt service and support
will be available. (For the instrument-specific warranty period, please refer to the
“Limited Warranty” section in the Terms and Conditions of Sale on our website at:
http://www.teledyne-api.com.
COVERAGE
After the warranty period and throughout the equipment lifetime, TAPI stands
ready to provide on-site or in-plant service at reasonable rates similar to those of
other manufacturers in the industry. All maintenance and the first level of field
troubleshooting are to be performed by the customer.
NON-TAPI MANUFACTURED EQUIPMENT
Equipment provided but not manufactured by TAPI is warranted and will be
repaired to the extent and according to the current terms and conditions of the
respective equipment manufacturer’s warranty.
PRODUCT RETURN
All units or components returned to Teledyne API should be properly packed for
handling and returned freight prepaid to the nearest designated Service Center.
After the repair, the equipment will be returned, freight prepaid.
The complete Terms and Conditions of Sale can be reviewed at
http://www.teledyne-api.com
CAUTION Avoid Warranty Invalidation
Failure to comply with proper anti-Electro-Static Discharge (ESD) handling and packing
instructions and Return Merchandise Authorization (RMA) procedures when returning
parts for repair or calibration may void your warranty. For anti-ESD handling and packing
instructions please refer to the manual, Fundamentals of ESD, PN 04786, in its “Packing
Components for Return to Teledyne API’s Customer Service” section. The manual can
be downloaded from our website at http://www.teledyne-api.com; RMA procedures are
under Return Authorization.
08354B DCN7877 Teledyne API T640 PM Mass Monitor v
ABOUT THIS MANUAL
This user manual, part number 08354, provides instructions for the setup,
installation, and operation of the T640 Real-time Continuous PM Monitor.
Support manuals, such as electrostatic discharge (ESD) prevention and various
communications, are available on the TAPI website http://www.teledyne-api.com
under Product Manuals.
We recommend that all users read this manual in its entirety before
operating the instrument.
08354B DCN7877 Teledyne API T640 PM Mass Monitor vi
TABLE OF CONTENTS
Safety Messages ...................................................................................................................................... ii
WARRANTY ............................................................................................................................................ iv
About This Manual ................................................................................................................................... v
Table of Contents .................................................................................................................................... vi
List of Figures .......................................................................................................................................... vii
List of Tables ........................................................................................................................................... ix
1. INTRODUCTION, SPECIFICATIONS, APPROVALS, AND COMPLIANCE ......................................... 10
Specifications .................................................................................................................................. 10
EPA Designation ............................................................................................................................. 11
Safety .............................................................................................................................................. 11
EMC ................................................................................................................................................ 12
2. INSTALLATION AND HARDWARE SETUP .......................................................................................... 12
Unpacking ....................................................................................................................................... 12
List of Standard Items .......................................................................................................... 13
List of Optional Accessories ................................................................................................. 13
Ventilation Clearance ........................................................................................................... 16
Instrument Layout ........................................................................................................................... 16
Front Panel ........................................................................................................................... 16
Rear Panel ........................................................................................................................... 17
Internal Layout ..................................................................................................................... 18
Height Dimensions ............................................................................................................... 19
Connections and Startup ................................................................................................................. 20
Power Connection ................................................................................................................ 20
Communications Interface Connections .............................................................................. 21
Aerosol Sample Conditioner (ASC) Connections and Installation ....................................... 21
Inlet Installation .................................................................................................................... 25
Indoor/Outdoor Installation .............................................................................................................. 27
Shelter Installation with Roof Penetration ............................................................................ 27
Outdoor Enclosure Installation ............................................................................................. 31
Pneumatics ...................................................................................................................................... 33
Display and Menu Navigation ......................................................................................................... 35
Startup and Functional Checks ....................................................................................................... 36
Startup .................................................................................................................................. 36
Functional Checks of Operating Parameters ....................................................................... 36
Initial Sensor Checks and Adjustments ................................................................. 37
3. SOFTWARE SETUP AND OPERATION ............................................................................................... 37
Menu System Overview .................................................................................................................. 37
Configuration and Setup ................................................................................................................. 38
HomeScreen ........................................................................................................................ 38
Dashboard ............................................................................................................................ 39
Alerts .................................................................................................................................... 40
Utilities>Datalog View .......................................................................................................... 40
Utilities>Alerts Log ............................................................................................................... 40
Utilities>USB Utilities (Downloads and Updates) ................................................................ 41
Downloading DAS (Data Acquisition System) Data .............................................. 42
Updating Software/Firmware ................................................................................. 42
Transferring Configuration to Other Instruments ................................................... 44
Generating a Report .............................................................................................. 45
Setup>Data Logging ............................................................................................................ 45
Creating a User-Defined Data Log ........................................................................ 46
Configuring Trigger Types ..................................................................................... 47
Downloading DAS (Data Acquisition System) Data .............................................. 48
Setup>Events ....................................................................................................................... 49
Creating User-Defined Events ............................................................................... 50
08354B DCN7877 Teledyne API T640 PM Mass Monitor vii
Editing or Deleting Events ..................................................................................... 51
Setup>Dashboard ................................................................................................................ 51
Setup>VARS (Variables) ................................................................................................... 52
Setup>Homescreen ........................................................................................................... 53
Setup>Instrument ............................................................................................................... 54
Instrument Display Calibration (for Earlier Instruments) ..................................... 54
Instrument Date/Time Adjustments ..................................................................... 56
Setup>Comm (Communications Setup) ............................................................................ 57
TCP Port1 ............................................................................................................ 57
TCP Port2 ............................................................................................................ 57
Network Settings ................................................................................................. 59
Operation ......................................................................................................................................... 60
4. SENSOR CHECKS AND ADJUSTMENTS ............................................................................................ 60
Ambient Temperature Sensor Check .............................................................................................. 61
Pressure Sensor Check and Calibration ......................................................................................... 62
Sample Flow Cal (5-LPM) ............................................................................................................... 63
Bypass Flow Cal (11.67-LPM) ........................................................................................................ 64
PMT Adjustment .............................................................................................................................. 65
Leak Check ..................................................................................................................................... 67
5. MAINTENANCE AND SERVICE ............................................................................................................ 68
Maintenance Schedule .................................................................................................................... 68
Maintenance Procedures ................................................................................................................ 69
Cleaning the T640 Inlet ........................................................................................................ 69
Cleaning the US EPA PM10 Inlet ........................................................................................ 70
Changing the Disposable Filter Unit (DFU) ......................................................................... 71
Checking Pump Performance .............................................................................................. 72
Checking the Volume Flow .................................................................................................. 72
Cleaning the Optical Chamber and the RH/T Sensor .......................................................... 73
Inspecting the Sampling Line ............................................................................................... 78
Checking for Leaks .............................................................................................................. 78
Troubleshooting and Service .......................................................................................................... 79
Fault Diagnosis .................................................................................................................... 79
Flow Problems ..................................................................................................................... 80
Calibration Problems ............................................................................................................ 80
Technical Assistance ........................................................................................................... 81
6. PRINCIPLES OF OPERATION .............................................................................................................. 81
Sampling System ............................................................................................................................ 82
Inlet ...................................................................................................................................... 82
Aerosol Sample Conditioner (ASC) ..................................................................................... 82
Optical particle Sensor ......................................................................................................... 82
Flow Sensor and Pump Control ........................................................................................... 82
Electronic Block Diagram ................................................................................................................ 83
APPENDIX A Warranty Repair Questionnaire .................................................................................... 84
APPENDIX B Menu Hierarchy ............................................................................................................ 86
LIST OF FIGURES
Figure 2-1. T640 Typical Set of Included Hardware ................................................................................... 14
Figure 2-2. 640x Option Typical Set of Included Hardware ........................................................................ 15
Figure 2-3. Front Panel Layout ................................................................................................................... 16
Figure 2-4. T640 Rear Panel....................................................................................................................... 17
Figure 2-5. T640 with 640x Option Rear Panel........................................................................................... 17
Figure 2-6. T640 Internal Layout, with 640x Option Components .............................................................. 18
08354B DCN7877 Teledyne API T640 PM Mass Monitor viii
Figure 2-7. Top View of Inlet Nozzle ........................................................................................................... 21
Figure 2-8. Inlet Nozzle Adapter for ASC Connection ................................................................................ 22
Figure 2-9. Collar for Lower Flange ............................................................................................................ 22
Figure 2-10. Set Screws for ASC ................................................................................................................ 23
Figure 2-11. Collar and ASC Adapter Support............................................................................................ 23
Figure 2-12. Ambient Temperature Probe and ASC Connections (T640 with 640X Option shown) .......... 24
Figure 2-13. T640 Sample Head (5-LPM) and ASC Assembly .................................................................. 25
Figure 2-14. 640X Option Inlet and ASC Assembly .................................................................................... 26
Figure 2-15. Ambient Temperature Sensor Probe Installed into Radiation Shield ..................................... 26
Figure 2-16. T640 Inlet Tube and Slip Coupler Assembly .......................................................................... 28
Figure 2-17. 640x Inlet Tube and Slip Coupler Assembly .......................................................................... 29
Figure 2-18. T640 Inlet and Sample Line Assembly ................................................................................... 29
Figure 2-19. 640x Inlet and Sample Line Assembly ................................................................................... 30
Figure 2-20. T640 Rooftop Sample Inlet and Extension Tubing Installation .............................................. 30
Figure 2-21. T640 (left) and 640x (right) Outdoor Enclosures Assembled ................................................. 32
Figure 2-22. T640 Pneumatics .................................................................................................................... 33
Figure 2-23. T640 with 640X Option Pneumatics ....................................................................................... 34
Figure 2-24. Sample Home Screen with Orientation .................................................................................. 35
Figure 2-25. Concentration Graph and Meter Graph .................................................................................. 36
Figure 3-1. Home Configuration thru Home Page Shortcut ........................................................................ 39
Figure 3-2. Dashboard ................................................................................................................................ 39
Figure 3-3. Alerts Log .................................................................................................................................. 40
Figure 3-4. USB Utility Pages ..................................................................................................................... 41
Figure 3-5: Das download Page ............................................................................................................ 42
Figure 3-6: Remote Update Page .......................................................................................................... 43
Figure 3-7: Manual Update Page (and other utilities) ............................................................................ 43
Figure 3-8: Configuration Transfer ........................................................................................................ 44
Figure 3-9: Report Generation Page ..................................................................................................... 45
Figure 3-10. Datalog Configuration, New Log Page ................................................................................... 45
Figure 3-11. Datalog Configuration, Existing Log ....................................................................................... 46
Figure 3-12. Creating a New Data Log ....................................................................................................... 46
Figure 3-13. Datalog Periodic Trigger Configuration .................................................................................. 47
Figure 3-14. Datalog - Conditional Trigger Configuration ........................................................................... 48
Figure 3-15. DAS Data Utility ...................................................................................................................... 48
Figure 3-16. Events Page ........................................................................................................................... 49
Figure 3-17. Event Configuration ................................................................................................................ 50
Figure 3-18. Existing Event for Viewing or Editing ...................................................................................... 51
Figure 3-19. Dashboard Configuration ........................................................................................................ 51
08354B DCN7877 Teledyne API T640 PM Mass Monitor ix
Figure 3-20. VARS Configuration Page ...................................................................................................... 52
Figure 3-21. Home Configuration thru Setup Menu .................................................................................... 53
Figure 3-22. Touchscreen Calibration Page ............................................................................................... 54
Figure 3-23. Date and Time Configuration Page ........................................................................................ 56
Figure 3-24. Communications Configuration, Network Settings ................................................................. 59
Figure 4-1. Leak-Check/Flow-Audit Adaptor Kit.......................................................................................... 61
Figure 4-2. Pressure Cal Menu ................................................................................................................... 62
Figure 4-3. Sample Flow Cal Menu ............................................................................................................ 63
Figure 4-4. Bypass Flow Cal Menu ............................................................................................................. 64
Figure 4-5. PMT Adjustment Menu ............................................................................................................. 65
Figure 4-6. Leak Check Menu ..................................................................................................................... 67
Figure 5-1. T640 Inlet (standard) ................................................................................................................ 69
Figure 5-2. 640X Option Disassembly ........................................................................................................ 70
Figure 5-3. Opening the Front Panel .......................................................................................................... 71
Figure 5-4. Internal DFU ............................................................................................................................. 71
Figure 5-5. External DFU, (with 640X Option only) .................................................................................... 72
Figure 5-6. Maintenance: Optics Chamber Windows ................................................................................. 76
Figure 5-7. Maintenance: Final Dusting ...................................................................................................... 76
Figure 6-1. T640 with 640X Option Electronic Block Diagram .................................................................... 83
LIST OF TABLES
Table 1-1. Specifications ............................................................................................................................. 10
Table 2-1. Ventilation Clearance ................................................................................................................. 16
Table 3-1. Setup>Instrument Menu ............................................................................................................ 54
Table 3-2. T640 MODBUS Register ........................................................................................................... 57
Table 3-3. LAN/Ethernet Configuration Properties ..................................................................................... 59
Table 5-1. Maintenance Schedule .............................................................................................................. 68
Table 5-2. Alerts and Recommendations .................................................................................................... 79
Appendix A: Warranty Repair Questionnaire
Appendix B: Menu Hierarchy
08354B DCN7877 Teledyne API T640 PM Mass Monitor 10
1. INTRODUCTION, SPECIFICATIONS,
APPROVALS, AND COMPLIANCE
The Teledyne API Model T640 with 640X Option is a real-time, continuous
particulate matter (PM) mass monitor that uses scattered light spectrometry for
measurement. The T640 measures 2.5 PM, and the 640X Option measures 2.5, 10,
and coarse PM.
SPECIFICATIONS
Table 1-1 presents the T640 PM Mass Monitor specifications.
Table 1-1. Specifications
PARAMETER
SPECIFICATION
Measurement Principle 90° white-light scattering
Light Source Polychromatic LED
Particle Size Resolution 0.18 20µm over 256 channels, combined to 64 channels for mass calculation
PM Mass Resolution
Measurement Range
0.1 10,000 µg/m
3
Mass Measurement & Display
Resolution
0.1 µg/m
3
Precision +/- 0.5 µg/m
3
(1-hr average)
Lower Detectable Limit < 0.1 µg/m
3
(1-hr average)
Mass Concentration Accuracy
T640
640X Option
Exceeds US EPA Class III PM2.5
Exceeds US EPA US EPA PM10 FEM and Class III PM2.5 & PM10-2.5 FEM
performance requirements for additive and multiplicative bias compared to FRM
samplers
Flow Rate
T640
640X Option
5.0-LPM
5.0-LPM + 11.67-LPM bypass flow
Flow Accuracy Within +/-1%; (Typically within +/- 0.5%)
AC Power
Instrument
External pump
(640X Option only)
Rating Typical Power Consumption
110-120 V, 60 Hz 3.0 A
220V-240V, 50/60 Hz 3.0 A
110-120 V, 60 Hz 3.0 A
220V-240V, 50/60 Hz 3.0 A
<120 W (at 120 VAC)
<120 W (at 120 VAC)
<360 W (at 120 VAC)
<360 W (at 120 VAC)
Communication
1 Ethernet: 10/100Base-T (supports MODBUS and HTTP polling protocols)
2 USB device ports
Data Storage 4 Gb memory allows for >1 year of data storage
Minimum Resolution (data rate): 10 seconds, user-definable
08354B DCN7877 Teledyne API T640 PM Mass Monitor 11
PARAMETER
SPECIFICATION
Dimensions
ASC (heater tube)
ASC w/T640 inlet
ASC w/640X Option inlet
Optional external shelter
H x W x D: 7" x 17" x 14" (178 x 432 x 356 mm)
43” (1092 mm) above the lid
53.5” (1359 mm) above the lid
70” (1778 mm) above the lid
HxWxD: 45” x 25” x 25” (1143 x 635 x 635 mm)
Weight
19 lbs (8.6 kg)
w/ T640 ASC + inlet 27 lbs (12.2 kg);
w/ 640X Option ASC + inlet 30 lbs (13.6 kg)
Operating Conditions
Operating temperature
Ambient temperature
Ambient Relative Humidity
Sample Humidity Control
0 - 50°C, non-condensing
-40 - 60°C
0 - 100%
Aerosol Sample Conditioner (ASC) 24VDC 90W (max) heater controlled to
35% RH
Environmental Conditions Installation Category (Over voltage Category) II Pollution Degree 2
For outdoor use only, to 5000 m altitude
1
As defined by the US EPA
2
At constant temperature and pressure
EPA DESIGNATION
TAPI’s Model T640 PM Mass Monitor and its options are officially designated as
US EPA Federal Equivalent Methods (FEMs) for determining compliance with
particulate matter mass concentration National Ambient Air Quality Standards
(NAAQS). The US EPA designation numbers are as follows:
EQPM-0516-236
EQPM-0516-238
EQPM-0516-240
EQPM-0516-239
The official List of Designated Reference and Equivalent Methods is published in
the U.S. Federal Register: http://federalregister.gov/a/2016-16578
. .
Comply with Code of Federal Regulations, Title 40 (downloadable from the U.S.
Government Publishing Office at http://www/gpo.gov/fdsys/
) and with Quality
Assurance Guidance documents (available on the EPA website,
http://www.epa.gov/ttn/amtic/qalist.html). Give special attention to specific
regulations regarding methods for determining particulate matter.
SAFETY
IEC/EN 61010-1:2010 (3
rd
Edition), Safety requirements for electrical equipment
for measurement, control, and laboratory use.
CE: 2006/95/EC, Low-Voltage Directive
08354B DCN7877 Teledyne API T640 PM Mass Monitor 12
EMC
IEC/EN 61326-1, Class A Emissions/Industrial Immunity
EN55011 (CISPR 11), Group 1, Class A Emissions
FCC 47 CFR Part 15B, Class A Emissions
CE: 2004/108/EC, Electromagnetic Compatibility Directive
2. INSTALLATION AND HARDWARE SETUP
This section addresses the procedures for unpacking the instrument and inspecting
for damage, presents clearance specifications for proper ventilation, and shows the
instrument layout.
UNPACKING
Verify that there is no apparent external shipping damage. If damage has occurred,
please advise the shipper first, then contact Teledyne API.
Included with your instrument is a printed record of the final performance
characterization performed on your instrument at the factory. This record,
titledT640/640x Mass Monitor Test Data Sheet, is an important quality assurance
and calibration record and should be placed in the quality records file for this
instrument.
WARNING ELECTRICAL SHOCK HAZARD
Never disconnect PCAs, wiring harnesses or electronic
subassemblies while under power.
With no power to the unit, carefully remove the top cover of the instrument and
check for internal shipping damage by carrying out the following steps:
1. Carefully remove the top cover and check for internal shipping damage.
a. Remove the cover screws located on the sides of the instrument.
b. Slide the cover backward until it clears the instrument’s front bezel.
c. Lift the cover straight up.
2. Inspect the interior to ensure all circuit boards and other components are
intact and securely seated.
3. Check the connectors of the various internal wiring harnesses and pneumatic
hoses to ensure they are firmly and securely seated.
4. Using the paperwork accompanying the instrument, verify that all of the
standard and optional hardware ordered with the unit has been installed.
These are listed on the paperwork accompanying the instrument.
08354B DCN7877 Teledyne API T640 PM Mass Monitor 13
LIST OF STANDARD ITEMS
Model T640 Instrument with power cord and Test Data Sheet:
SpanDust
TM
bottle with calibration certificate
Aerosol Sample Conditioner (ASC) Tube (~43” long)
Ambient Temperature Sensor Cable (25’) with radiation shield and mounting
bracket
Internal Temperature Sensor Cable (4’) for performing flow sensor
calibrations from inside shelter without having to disconnect the normally
installed ambient temperature sensor cable
CD with operating manuals
LIST OF OPTIONAL ACCESSORIES
Sample head, 5LPM (for T640 base model; PM2.5 FEM)
o Sample Head
o Water collection jar
o ~6” upper inlet tube
T640 base model extension tube kit
o 8’ long aluminum tube (5/8” OD) with locking collar
o Roof flange with 5/8” cord grip and ¼” cord grip (for ambient temp sensor
cable)
o Slip coupler (5/8” ID)
640x option
o US EPA PM10 inlet, 16.7 LPM
o Outer extension tube (~12” length)
o Inner extension tube (~8” length)
o External vacuum pump pack, 120 or 220V AC with tubing
o Bypass flow splitter / adapter (usually pre-installed onto the ASC from
the factory)
o ¼” black bypass flow tubing
640x extension tube kit
o 8’ long aluminum tube (1” OD)
o Step down adapter (1 ¼ ” ID to 1” ID)
o Slip coupler (1” ID)
o Roof flange with 1” cord grip and ¼” cord grip (for ambient temp sensor
cable)
o Slip coupler (5/8” ID, 1 ¼” OD)
Support tripod with cord grips for 5/8” or 1” OD tubes
Leak check / flow audit adapter kit
08354B DCN7877 Teledyne API T640 PM Mass Monitor 14
Figure 2-1. T640 Typical Set of Included Hardware
08354B DCN7877 Teledyne API T640 PM Mass Monitor 15
Figure 2-2. 640x Option Typical Set of Included Hardware
08354B DCN7877 Teledyne API T640 PM Mass Monitor 16
VENTILATION CLEARANCE
Whether the Monitor is set up on a bench or installed in an instrument rack, be sure
to leave sufficient ventilation clearance.
Table 2-1. Ventilation Clearance
AREA
MINIMUM REQUIRED CLEARANCE
Back of the instrument
10 cm / 4 in
Sides of the instrument
2.5 cm / 1 in
Above and below the instrument
2.5 cm / 1 in
INSTRUMENT LAYOUT
FRONT PANEL
Figure 2-3 shows the front panel layout, which has the display screen, two USB
ports for peripheral device connections: mouse and keyboard as alternatives to the
touchscreen interface, or flash drive for uploads/downloads (devices not included).
Figure 2-3. Front Panel Layout
08354B DCN7877 Teledyne API T640 PM Mass Monitor 17
REAR PANEL
The rear panel shows fittings and connectors for the monitor’s functions as well as
connectors for communication.
Figure 2-4. T640 Rear Panel
Figure 2-5. T640 with 640x Option Rear Panel
08354B DCN7877 Teledyne API T640 PM Mass Monitor 18
INTERNAL LAYOUT
Below shows the main components and assemblies of the monitor.
Figure 2-6. T640 Internal Layout, with 640x Option Components
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88

Teledyne API T640 User manual

Category
Measuring, testing & control
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI