BCM EBC5852-C8 Quick Start Card

Brand: BCM

Model: EBC5852-C8

Category: Computer cases

Type: Quick Start Card

SATA cable















User’s Quick Start Card

Version 1.00

http://www.bcmcom.com

Inspect the Package:

One EBC5852-C8 Motherboard

One IDE Cable

One

SATA Cable

One

K/B & M/S Y type cable

One Driver CD/DVD

One User’s Quick Start Card

Responsibility:

This manual is provided “As-Is” with no warranties of any kind, expressed or implied, including, but not limited to the

implied warranties or conditions of this product’s fitness for any particular purpose. In no event shall we be liable for any

loss of profits, loss of business, loss of data, interruption of business, or indirect, special, incidental, or consequential

damages of any kind, even the possibility of such damages arising from any defect or error in this manual or product. We

reserve the right to modify and update the user manual without prior notice.

WARNING: CMOS Battery Damage

Replace your system’s CMOS RAM battery only with the identical CR-2032 3V Lithium-Ion coin cell (or equivalent) battery

type to avoid risk of personal injury or physical damage to your equipment. Improper installation might cause battery to

explode. Always dispose of used batteries according to the manufacturer’s instructions, or as required by the local

ordinance (where applicable). The damage due to not following this warning will void your motherboard’s manufacturer

warranty.

Additional Information:

Additional information on setting this board up can be found in the User’s Manual in the provided CD or DVD ROM. The

Online User’s Manual and FAQ/Knowledge Base can be found on our website by visiting our website:

http://www.bcmcom.com. If your question is not answered in our FAQ/Knowledge Base, visit our forums and post your

messages or submit a new FAQ through FAQ Submittal form for us to add your question in our FAQ with our answer.

ATTENTION: Incorrect BIOS Setup

If you do not know how to handle BIOS setup or how to set it up properly, it is strongly advisable that you do not modify

any of the settings than otherwise instructed in the User’s Quick Start Card. Even a seemingly small incorrect adjustment

or modification in the BIOS setup can render your system unstable or unusable. Incorrect BIOS setup is not covered by

your motherboard’s manufacturer warranty. Try Clear CMOS information when system does not boot after BIOS settings

change.

EBC5852-C8

K/B & M/S Y

type cable

Audio Line_Out header (CN10)

Pin # Assignment Pin # Assignment

1 LOUT_L 1 LOUT_L

2 AU_GND 2 AU_GND

3 VCC 3 VCC

4 LOUT_R 4 LOUT_R

USB 2/3 header (CN11); USB 4/5 header (CN12)

Pin # Assignment Pin # Assignment

1 VCC 2 VCC

3 USB2 -

USB4 -

4 USB3 -

USB5 -

5 USB2 +

USB4 +

6 USB3 +

USB5 +

7 Ground 8 Ground

9 --- 10 NC

CD_In header (CN13)

Pin # Assignment

1 CD_IN_Left

2 CD_GND

3 CD_GND

4 CD_IN_Right

LAN1 LED header (CN14); LAN2 LED header (CN16)

Inverter connector (CN15)

Pin # Assignment

1 Ground

2 NC

3 LCD_BKL

4 Ground

5 +12V

COM2 connector (CN20)

Pin # Assignment Pin # Assignment

1 DCD (Data

Carrier Detect)

2 DSR (Data Set

Ready)

3 RXD (Receive

Data)

4 RTS (Request to

Send)

5 TXD (Transmit

Data)

6 CTS (Clear to Send)

7 DTR (Data

Terminal Ready)

8 RI (Ring Indicator)

9 Ground

Pin # Assignment Pin # Assignment

1 LINK_LED 2 VCC_3V

3 ACT_LED 4 VCC_3V

LVDS panel interface (CN17)

SMBus connector (CN22)

Pin # Assignment

1 SMBData

2 SMBClock

3 Ground

4-pins 12V/5V

output power connector (CN24)

Pin # Assignment

1 +12V

2 Ground

3 Ground

4 5V

System panel indicate pin-header (CN25)

Pin # Assignment Pin # Assignment

1 NC 2 NC

3 Ground 4 Ground

5 YAM0 6 YAM1

7 YAP0 8 YAP1

9 Ground 10 Ground

11 YAM2 12 CLKAM

13 YAP2 14 CLKAP

15 Ground 16 Ground

17 YAM3 18 YBM0

19 YAP3 20 YBP0

21 Ground 22 Ground

23 YBM1 24 YBM2

25 YBP1 26 YBP2

27 Ground 28 Ground

29 CLKBM 30 YBM3

31 CLKBP 32 YBP3

33 NC 34 +12V

35 NC 36 +12V

37 NC 38 VCC_LCD

39 BKL 40 VCC_LCD

Pin # Assignment Pin # Assignment

SPEAKER PWR LED

1 +5V 2 5V

3 NC 4 NC

5 BZ 6 Ground

7 SPKR KEYLOCK

HDD LED 8 KBLOCK

9 5V 10 Ground

11 HDLED- 12 NC

RESET PWR ON

13 RESET+ 14 VCC

15 Ground 16 PWRBT-

WARNING: Electrostatic Sensitive Device (ESD)

Static electricity can easily damage your motherboard and will void your motherboard warranty. Keep the motherboard

and other system components in their anti-static packaging until you are ready to install them. Touch a grounded surface

before you remove any system component from its protective anti-static packaging. Unpacking and installation should be

done on a grounded, anti-static mat. The operator should be wearing an anti-static wristband, grounded at the same

points as the anti-static mat. During configuration and installation touch a grounded surface frequently to discharge any

static electrical charge that may have built up in your body. Avoid touching the components when handling the

motherboard or a peripheral card. Handle the motherboard and peripheral cards either by the edges or by the peripheral

card case-mounting bracket.

WARNING: Misplaced Jumper Damage

Incorrect jumpers and connectors settings may lead to damage to your motherboard and will void your motherboard

warranty. Please pay special attention to not connect these headers in the wrong direction. DO NOT change ANY jumpers

while the motherboard has power.

Jumper / Connector

Jumper Description Note

CN1 CRT VGA port connector

3 pin

CN2 COM1 RS-232 serial port connector

3 pin

CN3 Audio MIC_In phone jack

3 pin

CN4 Audio Line_Out phone jack

3 pin

CN5 PS/2 keyboard or mouse connector

2 pin

CN6 Ethernet RJ-45 connector

44 pin

CN7 USB 0/1 connectors

CN8 Ethernet RJ-45 connector

CN9 DC-In power jack

4 pin

CN10 Audio Line_Out pin-header

2x7 pin (keyed)

CN11 USB 2/3 pin-header

3 pin

CN12 USB 4/5 pin-header

3 pin

CN13 CD-In pin-header

3 pin

CN14 LAN1 LED pin-header

2 pin

CN15 Inverter connector

44 pin

CN16 LAN2 LED pin-header

CN17 LVDS panel interface

CN18 Primary IDE connector

4 pin

CN20 COM2 serial port connector

2x7 pin (keyed)

CN21 CPU fan power connector

CN22 SMBUS connector

CN24 4-pins 12V/5V output power

connector

CN25 System panel indicate pin-header

2x5 pin (keyed)

Connector Description Note

JP2 BIOS write protection setting select

3 pin

JP3 LVDS voltage setting select

3 pin

JP4 Watchdog timer setting select

3 pin

JP5 Chassis Intrusion detection

3 pin

JP6 Clear CMOS setting select

2 pin

JP7 Auto power on setting select

2x5 pin (keyed)

BIOS write protection (JP2)

BIOS write protection Normal*

LVDS voltage select (JP3)

3.3V* 5V

Watchdog timer setting (JP4)

NMI Reset System*

Chassis Intrusion detection (JP5)

Trigger chassis intrusion Normal*

Clear CMOS (JP6)

Normal* Clear CMOS

Auto power on setting (JP7)

Auto power on Normal*

Motherboard Layout:

BCM EBC5852-C8 Quick Start Card

Brand: BCM

Model: EBC5852-C8

Category: Computer cases

Type: Quick Start Card

Download PDF

report

BCM EBC5852-C8 Quick Start Card

BCM EBC5852-C8 Quick Start Card

Related papers

Other documents