Crestron CNWMBG2-34A User manual

Brand: Crestron

Model: CNWMBG2-34A

Type: User manual

Crestron CNWMBG2-34A is a wired wall-mount panel designed for use with CRESNET II control systems. It features 30 miniature pushbuttons with self-contained feedback LEDs, two bargraph indicators with corresponding miniature pushbuttons, and a 4-pin connector for connection to the CRESNET II network.

The CNWMBG2-34A is fully customizable, with options for custom panel finishes, engraving, colored button caps, and omission of unused buttons. It can be programmed using CRESTRON CRESNET II Workshop Version 4.00 or later and requires CRESNET II Operating System SR30160.OPS or later.

CRESTRON CNWMBG2-34A Wall-Mount Wired Panel

REMOTE CONTROL SYSTEMS

1 DOC. 8002B

Specifications subject to change without notice.

1 2 3

UP1 UP2

DOWN1 DOWN2

BAR 2BAR 1

100

CRESTRON

4.63 in

11.76 cm

4.63 in

11.76 cm

Panel installs in 4-gang electrical box (1.60 in (4.06 cm) minimum depth).

SYNTAX:

NET.ID <10 to FE>: CNWP

i1,o1 = <signal name> \ button and LED combined

i2 = <signal name> \ independent button

o2 = <signal name> \ independent LED

" = " "

i30 = <signal name>

o30 = <signal name>

BAR1 = <signal name> \ left bargraph

UP1 = <signal name> \ left volume up button

DOWN1 = <signal name> \ left volume down button

BAR2 = <signal name> \ right bargraph

UP2 = <signal name> \ right volume up button

DOWN2 = <signal name> \ right volume down button

DESCRIPTION:

The CNWMBG2-34A wired panel interfaces to a CRESNET II control system over the CRESNET II network. The panel uses

30 miniature pushbuttons with self-contained feedback LEDs. Two bargraph indicators are included. Each bargraph has two

miniature pushbuttons. The CNWMBG2-34A is designed for wall-mounting using a standard four-gang electrical box.

Custom panel finishes, engraving, colored button caps, and the omission of unused buttons are all standard.

CRESTRON CNWMBG2-34A Wall-Mount Wired Panel

REMOTE CONTROL SYSTEMS

2 DOC. 8002B

Specifications subject to change without notice.

Each unique panel or component on the CRESNET II network requires the setting of an identity code (ID CODE). ID CODES are

two-digit hexadecimal numbers, from 10 to FE. The ID CODE of the panel should be set to match the ID CODE specified in the

NET.ID statement of the CRESNET II SIMPL-C program referencing the panel (refer to syntax section). To set an ID CODE,

remove the panel from the electrical box and disconnect power.

Accessible through the back plate are two miniature circuit-mounted rotary switches, identified as H and L. These 16-

position hexadecimal switches can be set to 0 through F. Using a small screwdriver, rotate the arrow in the center of the

switch marked H to point to the first (or most-significant) digit or letter of the specified ID CODE. Set the switch marked L to

the second (least-significant) digit or letter of the specified ID CODE.

The 4-pin connector marked NET should be wired to the CRESNET II network. Network termination points are available at

the control system power supply. Network units may also be daisy-chained together. Refer to the latest revision of the

CRESNET II reference manual section on CNPWS power supplies (Doc 8017 or Doc. 8091) for wire gauge specifications and

connection details.

The panel drawing on the previous page shows the location of the SIMPL-C button numbers and their corresponding button

positions. Buttons or bargraphs which are not used need not be assigned a signal name.

REQUIRES:

CRESNET II Workshop Version 4.00 or later.

CRESNET II Operating System SR30160.OPS or later.

FURTHER INQUIRIES:

If after reviewing this information you still have additional questions, please contact a CRESTRON technical support

representative by dialing (888) CRESTRON [(888) 273-7876] or (201) 894-0660.

Crestron CNWMBG2-34A User manual

Crestron CNWMBG2-34A User manual

Crestron CNWMBG2-34A User manual

Related papers

Other documents