Crestron CNWM User manual

Category
Mice
Type
User manual

This manual is also suitable for

Crestron CNWM-10A is a wired wall-mount panel that features 10 miniature pushbuttons with self-contained feedback LEDs. It can be programmed to control various functions and devices within a Crestron home automation system. Each button can be assigned a specific command or action, such as turning on/off lights, adjusting volume, or changing channels. The panel's compact size and sleek design make it suitable for installation in any room of the house. It requires a CRESNET II control system and can be easily integrated into existing Crestron systems.

Crestron CNWM-10A is a wired wall-mount panel that features 10 miniature pushbuttons with self-contained feedback LEDs. It can be programmed to control various functions and devices within a Crestron home automation system. Each button can be assigned a specific command or action, such as turning on/off lights, adjusting volume, or changing channels. The panel's compact size and sleek design make it suitable for installation in any room of the house. It requires a CRESNET II control system and can be easily integrated into existing Crestron systems.

CRESTRON CNWM-10A Wall-Mount Wired Panel
REMOTE CONTROL SYSTEMS
1 DOC. 8001B
Specifications subject to change without notice.
109
87
65
43
21
CRESTRON
4.62 in
11.73 cm
2.86 in
7.26 cm
Panel installs in 1-gang electrical box (2.50 in (6.35 cm) minimum depth).
SYNTAX:
NET.ID <10 to FE>: CNWP
i1,o1 = <signal name> \ button and LED combined
i2 = <signal name> \ independent button
o2 = <signal name> \ independent LED
" = " "
" = " "
i10 = <signal name>
o10 = <signal name>
DESCRIPTION:
The CNWM-10A wired panel interfaces to a CRESNET II control system over the CRESNET II network. The panel uses 10
miniature pushbuttons with self-contained feedback LED's. The CNWM-10A is designed for wall-mounting using a standard
single-gang electrical box. Custom panel finishes, engraving, colored button caps, and the omission of unused buttons are all
standard.
Each unique panel or component on the CRESNET II network requires the setting of an identity code (ID CODE). ID CODES are
two-digit hexadecimal numbers, from 10 to FE. The ID CODE of the panel should be set to match the ID CODE specified in the
NET.ID statement of the CRESNET II SIMPL-C program referencing the panel (see syntax above). To set an ID CODE, remove
the panel from the electrical box and disconnect power.
CRESTRON CNWM-10A Wall-Mount Wired Panel
REMOTE CONTROL SYSTEMS
2 DOC. 8001B
Specifications subject to change without notice.
Accessible through the back plate are two miniature circuit-mounted rotary switches, identified as H and L. These 16-
position hexadecimal switches can be set to 0 through F. Using a small screwdriver, rotate the arrow in the center of the
switch marked H to point to the first (or most-significant) digit or letter of the specified ID CODE. Set the switch marked L to
the second (least-significant) digit or letter of the specified ID CODE.
The 4-pin connector marked NET should be wired to the CRESNET II network. Network termination points are available at
the control system power supply. Network units may also be daisy-chained together. Refer to the latest revision of the
CRESNET II reference manual section on CNPWS power supplies (Doc 8017 or Doc. 8091) for wire gauge specifications and
connection details.
The panel drawing on the previous page shows the location of the SIMPL-C button numbers and their corresponding button
positions. Buttons which are not used need not be assigned a signal name.
As of the date of manufacture, the unit has been tested and found to comply with specifications for CE marking.
REQUIRES:
CRESNET II Workshop Version 4.00 or later.
CRESNET II Operating System SR30160.OPS or later.
FURTHER INQUIRIES:
If after reviewing this information you still have additional questions, please contact a CRESTRON technical support
representative by dialing (888) CRESTRON [(888) 273-7876] or (201) 894-0660.
  • Page 1 1
  • Page 2 2

Crestron CNWM User manual

Category
Mice
Type
User manual
This manual is also suitable for

Crestron CNWM-10A is a wired wall-mount panel that features 10 miniature pushbuttons with self-contained feedback LEDs. It can be programmed to control various functions and devices within a Crestron home automation system. Each button can be assigned a specific command or action, such as turning on/off lights, adjusting volume, or changing channels. The panel's compact size and sleek design make it suitable for installation in any room of the house. It requires a CRESNET II control system and can be easily integrated into existing Crestron systems.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI