Avision IS17 Quick start guide

Brand: Avision

Model: IS17

Type: Quick start guide

Features

• Color/B&W scan selection

• 300/600 dpi scan selection

• Direct save JPEG/PDF file to microSD card

• Support microSD card up to 32 GB

• View photos in iPad

Package Contents

Portable scanner

USB Y Cable

Software CD

Accessories:

• Cleaning Cloth

• Pouch

• Rechargeable

Li-Ion battery

(CNP50)

• Calibration Sheet

Note:

1. One end of the supplied USB Y cable includes two USB connectors. These two connectors (one

labeled “Power Cable”, the other labeled “Data Cable”) are used to connect to your

computer at the same time to increase the transferring speed. However, if only one USB port

is available from your computer, please plug the connector labeled “Power Cable” to your

computer while charging the battery and plug the connector labeled “Data Cable” to your

computer while downloading the images.

2. Use the supplied USB Y cable only to this scanner. Using this USB Y cable to other devices may

cause your computer to malfunction.

Understand the LCD Screen and Button Functions.

1 Ready LED Show ready status or scan in progress

2 SD card indicator Pictures will be stored in micro SD card

3 Effect indicator Photo(Color) or BW(Black and White)

4 Battery indicator Battery is full， Empty battery

5 Resolution selector Press to choose STD(standard) or HQ

(high quality) resolution

6 Power/Scan button Hold 2 seconds to power on/press to start

scan and end scan.

7 Error LED A red flashing LED indicates error

conditions such as scanning too fast

8 Resolution indicator STD(300dpi) or HQ(600 dpi)

9 Counting indicator Show scan count

File format indicator JPEG or PDF

File format selector Press to choose JPEG or PDF

Color selector Press to choose Color or Black and white

[

Install the Battery

1. Push and remove the battery cover on the

scanner.

2. Load the battery into the battery container.

Make sure the battery is loaded with the

correct polarity. Note the copper strips on the

battery should be touching the copper strips

on the device inside the battery container.

3. Insert the battery cover.

Handy Scanner-Quick Start Guide

Charge the battery

Before using the scanner, you need to first charge the

battery by connecting the scanner to your computer with a

USB Y cable. (Connect the mini USB connector to the

scanner while connecting the two USB connectors to your

computer.)

During the charging process, the red LED is on. If the

battery is full, the green LED will be on

To charge the battery next time, be sure to turn off the

scanner first.

]

Install a microSD card

You must install a microSD card to the SD slot at the back of

the scanner to store your images. Gently press in until the

SD card is latched.

Turn on your scanner.

Press the “Scan” button ( ) for 2 seconds to turn on your

scanner. The green LED will be flashing and the red LED will

be solidly lit and then both LED will be extinguished.

Finally, a default working mode will be displayed as

illustrated.

To turn off your scanner, press the “Scan” button (

) again

for about 3 seconds. The scanner will be automatically shut

off if it is left idle for 3 minutes.

Choose your desired scan settings.

Choose your desired scan settings to suit different scanning task.

1. Press the “PDF JPEG” button to choose your file format between JPEG and PDF.

2. Press the “Photo BW” button to choose your image mode between PHOTO (Color) and BW (Black and white).

3. Press the “STD HQ” button to choose your resolution between STD (standard, 300 dpi) or HQ (high quality, 600 dpi).

Scan your documents.

1. Place your document on a flat surface. If you are scanning a book, hold the

book firmly with one hand.

2. Place the scanner horizontally on the start-scanning position marked by white

lines on four sides of the scanner.

3. Press the “Scan” button (

) on the scanner. “SP0” will be displayed on the

screen.

4. Hold the scanner and glide the scanner gently over the surface of the page as

illustrated.

5. During scanning, the scan speed (SP0~SP2) will be displayed on he screen.

“SP0” indicates the lowest speed while “SP2” is warning you the scan speed is

too fast. To obtain the best image quality, please keep your speed at the

lowest level (SP0).

6. To end your scan, press the “Scan” button (

) on the scanner again.

7. If a page is scanned successfully, “001” will be displayed on the screen. This

number indicates your scan count.

Note:

If you place the scanner vertically on the page, please select “PDF”, and then the “STD HQ”

button for about 5 seconds, the “Rotate 90° right” icon (

) will be shown in the screen.

Finally, scan the page from the right to the left. Your scanned image will be rotated and displayed

correctly. (Note only PDF file supports the rotation feature.)

View or download your scanned images.

1. To view or download your scanned images, you can

either remove the micro SD card and connect it to a

card reader, or connect the scanner to your computer

via a USB cable (a USB Y cable is recommended, be

sure to turn on your scanner).

2. Your computer should recognize the card or the

scanner as a Removable Disk.

3. Click the Removable Disk and you will find a folder of

“DCIM” is created and all the PDF files will be stored in

the subfolder of “200DOC” and the JPEG files in the

subfolder of “100PHOTO”. File name starts from

IMG_0001.pdf or IMG_0001.jpg.

Note:

1. M-PDF: The scanner supports multi-page PDF. Press “PDF JPEG” to select PDF file format. Start your scan by pressing

the “Scan” button and end your scan by pressing the Scan button again. The LED will be flashing for 5 seconds. Scan

next page in 5 seconds by pressing the “Scan” button and end your scan by pressing the “Scan” button again. (Repeat

the steps if you have more pages) The scanned pages will be combined in one single PDF file.

2. Auto Rotation (for PDF image only): If you wish to rotate your image 90° left or right, select PDF format by pressing

the “PDF JPEG” button first. Secondly, press the “STD HQ” button for about 5 seconds, the 90° right icon (

) will be

displayed. This indicates your image will be rotated 90° right. To rotate your image 90° left, press the “STD HQ” button

again for 5 seconds to show the 90° left icon (

). Your image will be rotated accordingly.

Specifications

Image Sensor: Contact Image Sensor (CIS) USB Port: USB 2.0 high speed

Max. Scan Size: 8.27”x 14” Battery Capacity:

700 pages (A4 size, color, 300 dpi)

Dimension: (LxWxH) 263 x 39 x 36 (mm) Weight: 195 g (without battery)

LCD Screen: 16 x 27.3 (mm) Battery: CNP-50 compatible(3.75V, 800mA)

Troubleshooting

If there is error during scanning, the error LED will be flashed in red and error codes will be displayed. Refer the following table

to clear the error conditions.

Error Problem/Cause Solution

E01 Scanning speed is too fast.

Press the Scan button to restore and rescan in a lower

speed.

E02 No micro SD card is inserted.

Insert a micro SD card and then press the Scan

button to restore.

E03 Micro SD card full or card error Free more space or insert a new micro SD card.

E04 Scanner time out. No scan in 30 seconds. Press the Scan button to restore and try again.

E06 Calibration error Recalibrate the scanner.

E05

No scan data detected. (Users press the Scan button again

without moving the scanner.)

Press the Scan button to restore and rescan.

E08 Low battery warning

Press the Scan button to restore and then charge the

battery.

none Vertical lines appeared on images (The glass and rollers of

scanner are dirty.)

Clean the glass and rollers with the supplied cleaning

cloth.

none Images look distorted. (Scanning speed is too fast.)

Scan again in a lower speed (SP0).

Warning and Precautions of the lithium-ion battery

Warning:

Danger warning to prevent the possibility of the battery from leaking, heating, explosion, please observe the following

precautions:

• Don’t immerse the battery in water and seawater. Please put it in cool and dry environment if no using.

• Do not discard or leave the battery near a heat source as fire or heater

• Being charged, using the battery charger specifically for that purpose

• Don’t reverse the positive and negative terminals

• Don’t connect the battery to an electrical outlet directly.

• Don’t connect the positive and negative terminal directly with metal objects such as wire. Short terminals of

battery is strictly prohibited, it may damage battery.

• Do not transport and store the battery together with metal objects such as necklaces, hairpins.

• Do not strike, throw or trample the battery.

• Do not directly solder the battery and pierce the battery with a nail or other sharp object.

• Do not use lithium ion battery and others different lithium polymer battery model in mixture.

• Prohibition of use of damaged cells.

• Don’t bend or fold sealing edge. Don’t open or deform folding edge. Don’t fillet the end of the folding edge.

• Don’t fall, hit, bend battery body.

• Battery pack designing and packing Prohibition injury batteries.

• Never disassemble the cells.

• Keep the battery away from babies.

• Any components contacting these two edges, they must be insulated.

Caution:

• Never place batteries or devices on or in heating devices, such as microwave ovens, stoves, or radiators. Batteries

may explode when overheated or its performance will be degenerate and its service life will be decreased.

• Do not use it in a location where is electrostatic and magnetic greatly, otherwise, the safety devices may be

damaged, causing hidden trouble of safety.

• If the battery leaks, and the electrolyte get into the eyes. Do not wipe eyes, instead, rinse the eyes with clean

running water, and immediately seek medical attention. Otherwise, eyes injury can result.

• If the battery gives off an odor, generates heat, becomes discolored or deformed, or in any way appear abnormal

during use, recharging or storage, immediately remove it from the device or battery charge and stop using it.

• Avoid charging batteries for more than a week, as overcharging may shorten battery life. Over time, unused

batteries will discharge and must be recharged before use.

• Disconnect chargers from power sources when not in use.

•

Use batteries only for their intended purposes.

• Store the battery at 0°C to 40°C.

• Avoid exposing your device and batteries to very cold or very hot temperatures. Extreme temperatures can cause

the deformation of the device and reduce the charging capacity and life of your device and batteries.

• Prevent batteries from contacting metal objects, as this can create a connection between the + and – terminals of

your batteries and lead to temporary or permanent battery damage.

• In case the battery terminals are dirt, clean the terminals with a dry cloth before use. Otherwise power failure or

charge failure may occur due to the poor connection with the instrument.

• Be aware discharged batteries may cause fire. Follow all local regulations when disposing of used batteries or

devices.

• Never crush or puncture the battery. Avoid exposing the battery to high external pressure, which can lead to an

internal short circuit and overheating.

P/N 251-0840-0 V100

Avision IS17 Quick start guide

Avision IS17 Quick start guide

Avision IS17 Quick start guide

Related papers

Other documents