GENERAL ASSEMBLY:
This highly detailed kit features precision-tooled
parts for ease of assembly, but care and patience must be exercised to achieve
optimal results. It is recommended that the builder examine the instructions
carefully and do a dry test fit of parts before applying cement. You will find
this very helpful, as it will allow you to gain a clear understanding of how the parts
fit together in order to best plan painting and final assembly.
SUB-ASSEMBLIES:
Note that this kit is intended to be built in
sub-assemblies. This makes building the kit far more manageable. It is very
important to note that you will also find it extremely advantageous to apply
paint and decals to sub-assemblies before completing final assembly.
Please see the other side of this instruction sheet for details on complex paint and
decal placement.
DECALS & PAINT:
This kit includes extensive water slide decals. These decals
are compatible with setting solution which can be applied to conform around
surface details. Paint is not required to produce satisfactory results. However, some
modelers prefer to add additional painted detail to their kits. See the diagrams on
this sheet for instructions regarding decal placement and optional paint specs. For
best results apply dull coat for final finish.
For more model building tips and techniques, visit the Workbench section of our
website at round2models.com/workbench
Special thanks to E. James Small for developing the window decals included in this kit. For
excellence in model building, visit his web site at
smallartworks.ca
round2models.com
®
ASSEMBLY INSTRUCTIONS
ROMULAN
™
WARBIRD
™
AMT753
© 2012. TM,
®
& © 2010 CBS Studios Inc. STAR TREK and related marks are trademarks of CBS Studios Inc. All rights reserved. © 2012 Paramount Pictures Corp. All rights reserved.
AMT and design is a registered trademark of round 2, LLC. © 2012 Round 2, LLC South Bend, IN 46628 USA. Product and packaging designed in the USA. Made in China. All rights
reserved.
DECAL & PAINT INSTRUCTIONS
ROMULAN WARBIRD
KEY TO DECALS
000
000
Left Side Decal Application
Right Side Decal Application
PAINT COLOR:
These are suggested colors
based on readily available modeling paint. Modelers
can research these craft at their own discretion.
Base color - RAF Ocean Grey Model Master #2057
Accent color - 50/50 mix - RAF “Type S” Model Master
#2049 & Russian Topside Blue Model Master #2126
KEY TO NUMBERING
14L
14R
18L
18R
19L
19R
13L
13R
15L
15R
27L
27R
22L
22R
23L
23R
16L
16R
17L
17R
20L
20R
12L
12R
11 L
11 R
10L
10R
25L
25R
26L
26R
24L
24R
9L
9R
8L
8R
7L
7R
6L
6R
5L
5R
4L
4R
3L
3R
2L
2R
1L
1R
28
28
Opaque plastic part
Clear plastic part
Step number
Completed Assembly
1
1
100
1
ROMULAN
WARBIRD
1
STARBOARD WARP DRIVE
2
PORT WAR DRIVE
3
MAIN HULL/FINAL ASSEMBLY
4
DISPLAY BASE ASSEMBLY
29
20
21
24
25
23
22
30
31
28
27
26
1
3
2
310
312
310
312
311
311
Cement the warp
engine (311) and
intercooler (310) to
inside of inner warp
drive housing (29). Cement
intercooler (310) to outer
warp drive housing (27).
Cement inner warp drive
housing to outer warp drive housing. Cement collector (312) to assembled
warp engine.
You may decide to paint the warp engines, intercoolers and collector
transparent blue. Before assembly, paint parts inside surface and mask off
outer surface when further painting takes place.
Cement bridge halves (20) and (21) together. Cement outer upper wing (22)
to inner upper wing (23). Cement outer lower wing (24) to inner lower wing
(25). Cement aft central deck halves (30) right and (31) left together. Cement
port warp drive (from Assembly 2) and starboard warp drive (from Assembly
1) to assembled lower wing. Cement aft control deck to lower wing
assembly. Cement upper wing assembly to lower wing assembly making
sure parts are aligned evenly. Cement bridge to hull wings before cement
fully cures.
Cement the warp
engine (311) and
intercooler (310) to
inside of inner warp drive
housing (28). Cement
intercooler to outer warp drive
housing (26). Cement inner warp
drive housing to outer warp drive
housing. Cement collector (312) to assembled warp engine.
You may decide to paint the warp engines, intercoolers and collector
transparent blue. Before assembly, paint parts inside surface and mask off
outer surface when further painting takes place.
Starboard
Warp Drive
Assembly
Port
Warp Drive
Assembly
Insert metal rod into
dome base. The base can
be used with or without
the use of the ball joint. If
desired, insert ball joint
into socket and place on
top of metal rod. Insert
ball joint top into model.
It may be necessary to
add a drop of glue to the
ball joint to hold the
model steady.
DOME BASE
BALL JOINT
METAL ROD
BALL JOINT
SOCKET
/