Nilfisk-ALTO MC 4M User manual

Nilfisk-ALTO
Brand
Nilfisk-ALTO
Model
MC 4M
Type
User manual

This manual is also suitable for

MC 3C - MC 4M
SERVICE MANUAL
SM MC 3C_ MC 4M Ver.1.0_March 2015
Preface
This service manual contains detailed description of the main repair work on the cold high
pressure washers MC 3C & MC 4M
Repair work requires a suitable working place with the necessary water and power supply.
If operating errors are evident, draw the customers attention to the ”Operators Manual”.
A fault in the high pressure washer can have several causes as described in the section on
troubleshooting.
Refer to the illustrated ”Spare Parts Catalogue” during repairs. It shows the assembly position
and the sequence in which the individual components should be assembled.
See ”Technical Service Bulletin” (TSB) sheets. They include information on technical
modifications that have been made after this repair manual was made.
”Technical Service Bulletin” sheets are also valid as a supplement to the spare parts list until
publication of a new edition.
”Service Manual” and ”Technical Service Bulletin” should be available at the workshop, where
the repairs are carried out.
It is not permitted to give them to third parties.
Use original Nilfisk-ALTO spare parts only.
A.
B.
C.
D.
E.
F.
G.
H.
I.
Special tools 69
Wiring diagrams 66 -68
Adjustment / Test 65 -65
Service / Repair 42 -64
Troubleshooting 40 -41
Function 38-39
Construction 34-37
Technical data 5 -33
Safety instructions 4
A
SM MC 3C_ MC 4M Ver.1.0_March 2015
Safety instructions
4
For your own safety
ESD measures
(electrostatic discharge)
Observe valid safety regulations
for electrical equipment. In
particular, observe the following
regulations:
IEC 60335-2-79
EN 60335-2-79
Additionally:
Also see national regulations
Before using the cleaner, always
read the ”Operators Manual” and
keep it readily available.
Only allow the high pressure
cleaner to be used by persons
who have been trained in its use
and who have been explicitly aut-
horized to use it.
Repair work should be carried
out by persons instructed in
electrical installations or by
trained electricians only.
Take the following ESD precautions before carrying out any
repairs to the electronics:
 Touch the earth conductor before repairing the cleaner
( to discharge electrostatic charge from your body ).
 Wear wrist band if necassary.
 Use a conductive floor covering or a conductive table cover.
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
5
Parentitemno: Descripon:
107146377 MC3C‐130/660220/1/60/15EXPT
Service data Unit Value
Model
MC 3C-130/660
Item no.
107146377
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
132
Pressure pump outlet @ Qiec bar
130
Pressure gun outlet @ Qiec bar
111
Retaining pressure* bar
164
Flow. Qiec l/min
9,2
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
3460
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0400
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
FLEXOPOWER PLUS 990 BEND W/O NOZZLE BLUE
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
91
Impactfactor calculated
2,8
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
36
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
6
Parentitemno: Descripon:
107146373 MC3C‐140/570230/1/50/13UK
Service data Unit Value
Model
MC 3C-140/570
Item no.
107146373
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
126
Pressure pump outlet @ Qiec bar
124
Pressure gun outlet @ Qiec bar
123
Retaining pressure* bar
172
Flow. Qiec l/min
8,4
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2800
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
25034
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
UNIVERSAL PLUS LANCE 990 BEND
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
91
Impactfactor calculated
2,5
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
36
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
7
Parentitemno: Descripon:
107146375 MC3C‐140/660230/1/50/16EU
Service data Unit Value
Model
MC 3C-140/660
Item no.
107146375
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
132
Pressure pump outlet @ Qiec bar
131
Pressure gun outlet @ Qiec bar
129
Retaining pressure* bar
164
Flow. Qiec l/min
9,3
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2800
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0370
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
UNIVERSAL PLUS LANCE 990 BEND
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
91
Impactfactor calculated
2,9
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
36
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
8
Parentitemno: Descripon:
107146371 MC3C‐150/570230/1/50/13XTUK
Service data Unit Value
Model
MC 3C-150/570 XT
Item no.
107146371
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
129
Pressure pump outlet @ Qiec bar
126
Pressure gun outlet @ Qiec bar
123
Retaining pressure* bar
172
Flow. Qiec l/min
8,4
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2800
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0340
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
LANCE FOR 4-IN-1 880 BEND
Secondary Lance Type
None
Hose
DN6X15M
Guarantied sound power
91
Impactfactor calculated
2,6
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
38
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
9
Parentitemno: Descripon:
107146376 MC3C‐150/660230/1/50/16EU
Service data Unit Value
Model
MC 3C-150/660
Item no.
107146376
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
132
Pressure pump outlet @ Qiec bar
130
Pressure gun outlet @ Qiec bar
129
Retaining pressure* bar
164
Flow. Qiec l/min
9,3
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2800
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0370
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
FLEXOPOWER PLUS 990 BEND W/O NOZZLE BLUE
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
91
Impactfactor calculated
3
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
36
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
10
Parentitemno: Descripon:
107146380 MC3C‐150/660230/1/50/16XTEU
Service data Unit Value
Model
MC 3C-150/660 XT
Item no.
107146380
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
134
Pressure pump outlet @ Qiec bar
132
Pressure gun outlet @ Qiec bar
127
Retaining pressure* bar
164
Flow. Qiec l/min
9,2
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2800
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0370
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
LANCE FOR 4-IN-1 880 BEND
Secondary Lance Type
None
Hose
DN6X15M
Guarantied sound power
91
Impactfactor calculated
3
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
38
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
11
Parentitemno: Descripon:
107146381 MC3C‐160/770400/3/50EU
Service data Unit Value
Model
MC 3C-160/770
Item no.
107146381
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
130
Pressure pump outlet @ Qiec bar
128
Pressure gun outlet @ Qiec bar
135
Retaining pressure* bar
186
Flow. Qiec l/min
11,8
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
Agip Rotra
Pump oil amount
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2800
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
25045
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
UNIVERSAL PLUS LANCE 990 BEND
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
94
Impactfactor calculated
3,6
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
36
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
12
Parentitemno: Descripon:
107146383 MC3C‐170/820220‐440/3/60EXPT
Service data Unit Value
Model
MC 3C-170/820
Item no.
107146383
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
145
Pressure pump outlet @ Qiec bar
143
Pressure gun outlet @ Qiec bar
142
Retaining pressure* bar
189
Flow. Qiec l/min
11,6
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
3380
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0435
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
FLEXOPOWER PLUS 990 BEND W/O NOZZLE BLUE
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
94
Impactfactor calculated
4
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
36
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
13
Parentitemno: Descripon:
107146385 MC3C‐170/820230‐400/3/50XTNO
Service data Unit Value
Model
MC 3C-170/820 230-400/3/50 XT NO
Item no.
107146385
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
147
Pressure pump outlet @ Qiec bar
145
Pressure gun outlet @ Qiec bar
141
Retaining pressure* bar
186
Flow. Qiec l/min
11,3
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
Agip Rotra
Pump oil amount
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2800
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0435
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
LANCE FOR 4-IN-1 880 BEND
Secondary Lance Type
None
Hose
DN6X15M
Guarantied sound power
94
Impactfactor calculated
4
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
38
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
14
Parentitemno: Descripon:
107146384 MC3C‐170/820400/3/50XTEU
Service data Unit Value
Model
MC 3C-170/820
Item no.
107146384
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
147
Pressure pump outlet @ Qiec bar
145
Pressure gun outlet @ Qiec bar
141
Retaining pressure* bar
186
Flow. Qiec l/min
11,3
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
Agip Rotra
Pump oil amount
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2800
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0435
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
LANCE FOR 4-IN-1 880 BEND
Secondary Lance Type
None
Hose
DN6X15M
Guarantied sound power
94
Impactfactor calculated
4
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
38
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
15
Parentitemno: Descripon:
107146382 MC3C‐170/820400/3/50EU
Service data Unit Value
Model
MC 3C-170/820
Item no.
107146382
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
146
Pressure pump outlet @ Qiec bar
143
Pressure gun outlet @ Qiec bar
142
Retaining pressure* bar
186
Flow. Qiec l/min
11,6
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA3
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2800
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0435
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
FLEXOPOWER PLUS 990 BEND W/O NOZZLE BLUE
Secondary Lance Type
None
Hose
DN6X15M
Guarantied sound power
94
Impactfactor calculated
4
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
36
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
16
Parentitemno: Descripon:
107145840 MC3C‐170/830400/3/50EU
Service data Unit Value
Model
MC 3C-170/830
Item no.
107145840
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
158
Pressure pump outlet @ Qiec bar
139
Pressure gun outlet @ Qiec bar
127
Retaining pressure* bar
175
Flow. Qiec l/min
11,6
Suction height dry m
-
Suction height primed m
0,5
Pump type
Comet
Number of pistons
3
Piston type
Stainless Steel
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2880
Electrical diagram no.
71413
UNIT DATA:
Nozzle size, water
NT 0450
Max. Inlet temp. (primed) °C
50
Max. Inlet temp. (suction) °C
50
Max. Inlet temp. (pressure fed) °C
60
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
FLEXOPOWER PLUS LANCE 990 BEND
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
97
Impactfactor calculated
4
Vibration ISO 5349, lance 1 / lance 2
<2,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
35
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
17
Parentitemno: Descripon:
107145841 MC3C‐170/830400/3/50XTEU
Service data Unit Value
Model
MC 3C-170/830 XT
Item no.
107145841
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
163
Pressure pump outlet @ Qiec bar
145
Pressure gun outlet @ Qiec bar
132
Retaining pressure* bar
200
Flow. Qiec l/min
11,6
Suction height dry m
-
Suction height primed m
0,5
Pump type
NA5 v1
Number of pistons
3
Piston type
Full Ceramic
Stroke mm
1
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,42
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
2880
Electrical diagram no.
71413
UNIT DATA:
Nozzle size, water
NT 0450
Max. Inlet temp. (primed) °C
50
Max. Inlet temp. (suction) °C
50
Max. Inlet temp. (pressure fed) °C
60
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
LANCE FOR 4-IN-1 880 BEND
Secondary Lance Type
None
Hose
DN6X15M
Guarantied sound power
97
Impactfactor calculated
4
Vibration ISO 5349, lance 1 / lance 2
<2,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
36
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
18
Parentitemno: Descripon:
107146398 MC4M‐100/770230/1/50/13UK
Service data Unit Value
Model
MC 4M-100/770
Item no.
107146398
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
86
Pressure pump outlet @ Qiec bar
83
Pressure gun outlet @ Qiec bar
80
Retaining pressure* bar
125
Flow. Qiec l/min
11,1
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA4
Number of pistons
3
Piston type
Painted Ceramic
Stroke mm
0
Pump oil type
SAE 80W-90 API GL-5
Pump oil amount L
0,39
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
1450
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
NT 0530
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
FLEXOPOWER PLUS 990 BEND W/O NOZZLE BLUE
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
86
Impactfactor calculated
2,9
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
39
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
19
Parentitemno: Descripon:
107146395 MC4M‐140/620230/1/50/13EU
Service data Unit Value
Model
MC 4M-140/620
Item no.
107146395
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
121
Pressure pump outlet @ Qiec bar
122
Pressure gun outlet @ Qiec bar
128
Retaining pressure* bar
167
Flow. Qiec l/min
8,7
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA4
Number of pistons
3
Piston type
Painted Ceramic
Stroke mm
0
Pump oil type
Agip Rotra
Pump oil amount
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
1450
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
25035
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
UNIVERSAL PLUS LANCE 990 BEND
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
86
Impactfactor calculated
2,8
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
39
Size - Machine alone L x W x H mm
382x382x1017
B
Technical data
SM MC 3C_ MC 4M Ver.1.0_March 2015
20
Parentitemno: Descripon:
107146396 MC4M‐140/620230/1/50/13UK
Service data Unit Value
Model
MC 4M-140/620
Item no.
107146396
TECHNICAL DATA
PUMP:
Pressure pump head @ Qiec bar
121
Pressure pump outlet @ Qiec bar
122
Pressure gun outlet @ Qiec bar
128
Retaining pressure* bar
167
Flow. Qiec l/min
8,7
Suction height dry m
0,5
Suction height primed m
1
Pump type
NA4
Number of pistons
3
Piston type
Painted Ceramic
Stroke mm
0
Pump oil type
Agip Rotra
Pump oil amount
ELECTRIC:
Electric data
Highvoltage (HV) test voltage kV
1,5
HV Insulation resistance
1
Earth circuit resistance
0,2
Pump revolutions
1450
Electrical diagram no.
0
UNIT DATA:
Nozzle size, water
25035
Max. Inlet temp. (primed) °C
25 (50 max.1 hour)
Max. Inlet temp. (suction) °C
25 (50 max.1 hour)
Max. Inlet temp. (pressure fed) °C
60 (>40°C max. 1h)
Gun Type
ERGO 2000 STANDARD GUN W/O HOSE SWIVEL
Primary Lance Type
UNIVERSAL PLUS LANCE 990 BEND
Secondary Lance Type
None
Hose
DN6 x 10m
Guarantied sound power
86
Impactfactor calculated
2,8
Vibration ISO 5349, lance 1 / lance 2
<1,5; +/-1
Protection Class
IPX5
Machine incl. standard acc. kg
39
Size - Machine alone L x W x H mm
382x382x1017
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71

Nilfisk-ALTO MC 4M User manual

Nilfisk-ALTO
Brand
Nilfisk-ALTO
Model
MC 4M
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents