Weller WAD 101 User manual

WELLER

Hot Air

Hot Air.........

.....the Solution for selective Reflow - Processes

For small Components

up to about15 X 15 mm

HAP 1

Connectable to an....

WAD 101

WMD 1A

WR 3M

WAD 101

Hot Air Station

WAD 101 Hot Air Station

The cost effective solution for

external compressed Air -, or Inert

Gas supply

WAD 101

Hot Air Unit

Consists of:

• Power supply

• Hot air pencil HAP1

• Support KH27

• Socket wrench 8mm

• 2 m air hose 6mmØ

WAD 101

- Soft Ware Features

• Digital control electronic with micro controller

• Automatic tool recognition

• Digital display for PRE-SET and READ value (auto return)

• Temperature control from 50 to 450°C for soldering and

550°C for hot air

• Standard setback of 20 min. without WCB

• Calibration box can be connected for programming, time

setback and lock-out

• User Window – access to change temperature in lock-out

mode within a predefined range

• ESD confirm, protection class 1

• Accuracy ± 30°C for Hot Air Tools

± 2% of final value

for Soldering Irons

WMD 1A

Hot Air Station

with integrated Pump

Consists of:

• Power Unit WMD 1S

with integrated

Rotation pump

• HAP 1 Hot Air Pencil 100

Watt

• AK10 Safety Rest

WMD 1A

Independent and Versatile

• Temperature setting infinitely

variable from 50 to 550°C

• Automatic Tool recognition

for tools up to 150 Watt

• Antistatic Metal box

• Potential balance (delivery

condition – direct grounded)

• Temp.Accuracy t ± 2% of final

value

• Maintain less free quick

starting Rotation Pump

WMD 1A

Soft Ware Function

• Automatic Tool recognition

corrects automatically physically based temperature variation of

different tools

• Automatic over load Protection

In case the electronic has to heat any tool uncontrolled for more

than 30 Min continuously, the power will be reduced to 80% to

avoid any damage.

• Setback

Temperature reduction to 150°C adjustable from 0 to 99 min.

• Offset

• To compensate temperature variations up to ± 40°C

For large Packages

up to about 43 X 43 mm

HAP3000 hand - operated

Permanent connected

to....

WHA 900

without Nozzle

Vacuum

WHA 3000V

with Nozzle

Vacuum

WHA 3000P

with

Nozzle Vacuum

HAP3000

Hot Air Nozzles

WHA 900 – no integrated

Vacuum possible

Mounted to....

WHA 3000V & WHA 3000P

• „Man“- Modus Press “VAC”

Button to activate the Nozzle

Vacuum

•„Auto “- Modus Nozzle

Vacuum will be activated

automatically in the end of the

Temperature Profile

Nozzle Vacuum

WHA 900

The portable Hot Air Station

for price conscious User

WHA 900

• Infinitely variable

Temperature setting from 50

to 550°C

• Continuously adjustable

airflow from 5 to 50 l / min.

• Stand -by parameter

unrestricted adjustable

• Offset setting at any

temperature possible

• Maintenance - free and

brushless turbine

WHA 900

Setting & Calibration

• Standby for constant nozzle

temperature and

elementary temperature

profile

• The only appliance within

that price level offering the

hot air calibration feature

• Offset scope ± 50°C

WHA 900

Stand By

• Activation

- set the desired parameter while the

appliance is in power off, keep

pushing the green button and power

on until the turbine reaches the final

speed.

- At active stand-by function the unit

will start with the predefined

parameter when powering on the

appliance

• Deactivation

- Push the green button and power

on the appliance, keep pushing the

button till the turbine stops.

WHA 900

einfaches Temperatur Profil

• Set stand-by Parameter and

activate

• Switch off the Appliance

• Position the hot air pencil,

( where applicable use

WHBS )

• Adjust desired soldering

Parameter

• Power on and wait until all

solder joints are properly

preheated

• Push start button and wait

until all solder joints are

reflowed

• Push stop button for the

final end

240°C

260°C

Power on

start

stop

Stand By setting Actual setting

WHA 900

Offset

• The adjustable offset scope is ± 50°C

• Calibration might be carried out at any desired

temperature.

Calibration Procedure

• Install temp. measurement nozzle, insert thermo

couple, and power on the appliance

• Set airflow to position 4 and air temperature to the

desired value

• Start operation (push green button) and wait until the

displayed temperature has been stabilized

• Push start button for about 15 sec. till the LED is

permanently illuminated

• Turn the setting potentiometer immediately to the

middle position. To correct any offset, by turning the

setting potentiometer slowly clock,- or counter

clockwise to meet the presetting.

• Push the green button to confirm and leave the offset

procedure.

For BGA Components

WHA 3000P Set

WHA 3000V Set

WHA 3000V

WHA 3000P

Self-Contained Hot Air Station

Consists of:

• Power Unit with HAP 3000

Hot Air Pencil 700 Watt

• Stop + Go Support AKT30

• Nozzle NQ30

• Nozzle Changer

WHA 3000P

complies to ESD Requirements

• Automatic and Manual Operating

Mode

• 3-Step Temperature/Time Profile

• PC Connectivity & Remote

Control via RS232

• Socket for External Sensor

• Remote Control of WHP

• Digital Temperature Adjustment

from 50 to 550°C

• Green LED shows Heating

Pulses

• Air Flow adjustable

from 5 to 50 l/min

• Stand-by Function for Pre-

heating of Nozzles and

Components

WHA 3000V

Hot Air Station for Use of

Compressed Air or Inert Gas

Consists of:

• Power Unit with HAP 3000

Hot Air Pencil 700 Watt

Stop + Go Support AKT30

• Nozzle NQ30

• Nozzle Changer

Weller WAD 101 User manual

Related papers

Other documents