Coway CHP-01AL User manual

Brand: Coway

Model: CHP-01AL

Type: User manual

Important Safety Information

Specification

Features of CHP-01AL

Names of Parts

Wiring Diagram/Water Flow Diagram

Coway’s Reverse Osmosis System

Operation Method

Cleaning Method

Specifications of Main Parts

Operational Principles

Troubleshooting

Caution to be Taken at Assemble

and Disassemble

Replacement of Each Component

Harness Diagram

Circuit Diagram

Exploded View

Appendix : Installation Manual

Contents

Important Safety Information

Read all the installation precautions and instructions carefully

and completely prior to beginning use. Periodic maintenance is

required in order for this product to perform as advertised.

For your safety, the information in this manual must be followed to

minimize the risk of property damage or personal injury.

Electricity Safety

Only connect the power cord to the voltage rating that matches it on the

rating plate to avoid danger such as electric shock or fire. And be sure the electric

outlet is in an inside location to protect from moisture.

Be sure the power cord not to be bent by force and do not put a heavy object on it

to avoid any electric leakage or damage.

Do not pull the power plug from the outlet with a wet hand or get the plug wet to

avoid electric shock.

Never splash the water filtration system with water to avoid the risk of electric shock.

Keep the cord out of heavy traffic areas. To avoid fire hazard, NEVER put the cord

under rugs, near heat resisters, radiator, stoves, or heaters.

Do not use a damaged power cord or plug, and loose consent where the plug

cannot be inserted securely to avoid fire or shock hazard. If the power cord is

damaged, it must be replaced by the manufacturer or its service agent or a similarly

qualified person in order to avoid a hazard.

Remove the power plug when not using for an extended period of time. Insulation

may deteriorate, causing short circuit, fire and/or electrical shock as a result.

Periodically remove dust from the power plug with a dry cloth. Dust build-up can

cause bad insulation and a fire may occur as a result.

Do not use with water that is microbiologically unsafe or unknown

quality without adequate disinfection before or after the system.

Installation & Use Safety

Keep the water filtration system out of direct sunlight. The sun's heat may distort

non-metallic parts and may damage the electronics.

Do not install the water filtration system where it could freeze. Freezing damage is

not covered by the warranty.

Keep the water filtration system away from place being humid and dust rising place

to avoid electric shock and fire. Never splash the water filtration system with water to

avoid the risk of electric shock.

If the water pressure at house is over the maximum working pressure of the water

filtration system (referring to the rating plate), install a pressure reducing valve in the

water supply line to it.

Only connect the water filtration system to cold water pipe. Do not run hot water

over 104 (40 ) through it. It will defect the filters of the water filtration system .

Periodical filter replacement is prerequisite for getting clean water. In case

filters are overused, the performance of filters is deteriorated. Therefore, do not miss

the time of filter replacement.

When water is stored or the product is not in use for a long time, discharge all the

water in the storage tank before use.

Install it more than 3.9inches(10cm) away from the wall for normal operation of

heater and compressor.

Do not repair, disassemble or modify. Fire and/or electrical shock may occur as a

result. For repair, contact your dealer of purchase or A/S center of Coway.

Do not allow the foreign or unexpected material into the storage tank. The filtered

water in the storage tank may be deteriorate as a result.

Immediately plug out in the case of a smoke or smell of fire to call to A/S center of

Coway. Electric shock or fire may occur as a result.

Plug out and call to A/S center of Coway in the case of any leakage from the product.

Specification

50GPD 14

Post-Carbon

Membrane

Pre-Carbon

Plus-Sediment

Cold

Storage

51kg (112.4 lb)Net Weight

430 (W) x 480(D) x 1460(H) mmDimension

7,200 /hr(25 ,60psi)Filtration Capacity Per Day

14 Silver Activated Carbon

14 , Activated Carbon

14 , Polypropylene, Stainless Steel

Filter

Reverse Osmosis (With Pump)Filtration Method

4.9(14.5)

23.7

Tank

Capacity

868 WPower Consumption

Voltage rating on the rating plateRating Voltage

CHP-01ALModel

Note

According to the water temperature of season, the actual amount of filtered water

may vary slightly.

Features of CHP-01AL

As the waterspout can be easily attached or detached, it is very convenient when

a large amount of water is taken at a time.

Names of Parts

Indication Parts/Operating Parts

Wiring Diagram

Water Flow Diagram

How does Coway's Water Filtration System Filter Out

Wastes?

The osmotic membrane phenomenon has been applied to Coway water filtration

system, where a TFC membrane with pores of 0.0001 (1/1,000,000 of hair) is used

to filter water. The components of our water filtration system are as follows;

Plus-Sediment Filter

Using a step-by-step filtration method per pore, this filter effectively reduces various

foreign bodies that come from the feed water pipe such as bits of rust and also protects

the membrane. The Plus-Sediment filter vastly reduces dirt, sand, rust particles, and other

sediment.

Pre-Carbon Filter

The activated carbon filter reduces chlorine, fluoride, odor, tri-halo methane, gas additive

MTBE, and organic pollutants such as pesticides, EDB, PCB, benzene, and TCE

Reverse Osmotic Membrane Filter

The reverse osmosis filter reduces cryptosporidium, viruses, coliform, bacteria, radioactive

radon, ethylene glycol(anti-freeze), arsenic, copper, iron, lead, manganese, as well as

dissolved chemical solids such as bicarbonate, cyanide, ferrocyanide, nitrates, and

nitrites.

Post-Carbon Filter

Made using coconut, this filter reduces unpleasant smell from water and enhances water

flavor.

UV Lamp

UV lamp circulates the treated water inside the reservoir tank so that it prevents

secondary contamination inside it

Coway’s Reverse Osmosis System

Note

This reverse osmosis system contains a replaceable treatment component, critical for the

effective reduction of total dissolved solids and that product water shall be tested

periodically to verify that the system is performing properly. Replacement of the reverse

osmosis component should be with one of identical specifications, as defined by the

manufacturer, to assure the same efficiency and contaminant reduction performance.

The disposed water shall be used for cleaning a toilet, a house, dishes, and

as water for sundry uses. However, please do not use it for potable water or

cooking water.

Estimated Time of Filter Replacement

The estimated replacement time of filter which is a consumable part is not an indication of

quality guarantee period, but it means the ideal time of filter replacement. Accordingly, the

estimated time of filter replacement may be shortened in case it is used in the area of

poor water quality or in case it is used a lot.

12-18 monthPost-Carbon Filter

When the UV lamp blinksUV lamp

12-24 monthMembrane Filter

8-12 monthPre-Carbon Filter

4-6 monthPlus-Sediment Filter

Usable PeriodNames of Filter

Water Filtration Process

Efficiency rating means the percentage of the influent water to the system that is available

to the user as reverse osmosis treated water under operating conditions that approximate

typical daily usage.

Note

Operation Method

Open the Adaptor and Connect to the Power

Connect it to voltage rating that matches it on

the rating plate. Then, open the adopter to

supply water to the water filtration system.

After installed, moved, and severely shaken, about 30minutes are needed for stabilization

of cooling device before using the product.

Note

How to Drink Hot Water

Installation of the water filtration system must comply with existing state or

local plumbing codes. After installation the power supply cord and plug shall

be accessible.

The temperature of hot water is over 176 (80 ). Therefore, be careful not

To get burned by the hot water

Operation Method

How to Drink the Cold Water

Turn on the cold water switch on

The front and make sure that the

Indicator of cold water is turned

On.

Continuous Extraction

Pull forward the cup-touch lever

of hot or cold water faucet to

Extract continuously water

Draining Water

Open the switch cover on the front and turn off the cold and hot water switch

Before unplugging power cord. Then, connect the hose to the drainage valve

To drain water

In the case of extracting hot water, push the safety button after pulling

Forward the cup-touch lever

Note

How to Use Water Spout

Cleaning Method

Note

Keep the surrounding environment clean all the time and clean the inside of the tank

once a month to get clean water

After cleaning, drain the first filtered water before drinking the water.

Specifications of Main Parts

1 Regulator

-Use: It uniformly keeps the water pressure of the system inside.

- Operation Principle : It keeps the pressure of supplying water under the setting

pressure by utilizing the spring tension.

3 Plus-Sediment Filter

-Material: Polypropylene

-Feature: By using a cartridge filter which has a stage-by-stage filtration method in

accordance with the size of pore, the early clogging condition of filter has been improved.

4 Pre-Carbon Filter

-Material: 12 x 30 mesh by granular activated carbon of coconut.

- Feature : It has an outstanding ability to reduce carcinogenic substance (THMs) and

organic chemical substance.

5 R/O Membrane Filter

- Capacity : 50GPD on 25 , 20psi

-Material: Polyamide, Polysulfone

- Pore size : 0.0001 m

-Feature: Various contaminating inorganic substances including bacteria and virus are

reduced through fine pores of 0.0001 in diameter.

6 Post-Carbon Filter

- Material : 20 x 40 mesh by silver-added activated carbon of coconut.

-Feature: It improves hygienic condition and taste of water by adding the silver- added

activated carbon to reduce odor in the water and prevent proliferation of microbe.

2 Thermistor

-Use It controls the temperature of the cold water.

- Operation Principle It controls the operation of compressor detecting the temperature of

the compressor by change of resistance that varies rapidly and predictably with temperature.

7 UV Lamp( Single body type )

- Material : Quartz glass tube and pump

-Feature: UV lamp circulates the treated water inside the reservoir tank so that it prevents

contamination inside it.

8 Boost Pump(CHP-01AL)

-Use: It pressurizes the feed water to the proper pressure.

- Operation Principle : It keeps proper water pressure by pressurizing the feed water,

and it helps exercise its ability of filtering a certain amount of water even in the low

pressure area.

9 Lower Pressure Switch(L.P.S)

-Use: It controls the operation of Boost Pump (On/Off)

- Operation Principle : In the case of low water pressure, it makes the pump stopped for

prevention of running idle. As the water pressure is recovered, it makes pump resume

automatically.

10 Disposed Water Valve

-Use: It controls the ratio of disposed water to purified water.

- Operation Principle : It automatically controls the ratio of disposed water to filter water with

the pressure of tap water by spring force.

Operational Principles

Power Part

1 Rating Voltage

120Vac 60

2 Power Transformer

Configurations of Main Part

- Hot Water Selection Switch

As the switch is “On”, heating mode is selected

and Heater starts to hot water temperature.

- 150 (65 ) Hot Water Selection Switch

As the switch is “On”, 150 (65 ) heating mode is

selected

and hot water temperature is controlled under

150

(65 ).

- Cold Water Selection Switch

As the switch is “On”, cooling mode is selected

and compressor starts to cold water temperature.

- Cold II Cold Water Selection Switch

As the switch is “On”, Cold II cooling mode is selected

and it is used for extending cold water.

Tact Switch

- Hot Thermistor : 95 3%, Rth=15.78

- Cool Thermistor : 4 2%, Rth=133.5

- Water Level Sensor (Low/Middle/High) : Reed switch

- O/F Sensor : Sensing the overflow

-LPS: Sensing the flow of Feed water

- UV CDS : Sensing the lighting of UV Lamp

Input Controller

NoteSpecificationComponent

S1 23.1Vac 1.5A

S2 12.5Vac 0.5A

15% of rating voltage

CHP-01AL

SecondaryPrimaryModel

3 Fuse

15A 250Vac (Littelfuse : 65TS)

Operational Principles

Power Part

As impressing main initial power, the water filtration starts to

sensor input condition.

Initial Starting

- Feed Valve : Feed water control, 24Vdc 0.25A

- NOS Valve

: Feed water control when is overflow, 24Vdc 0.25A

- UV Pump : Circulating the stored water, 12Vac 0.3A

- Circulation Pump

: Circulating the cool water, 24Vac 0.5A

- Boost Pump : Pressurizing feed water, 24Vac 0.8A

- UV Lamp : Sterilization of stored water, 120Vac 60 , 4W

-Heater: Heating device, 120Vac 60 , 600W(5A)

- Compressor : Cooling device, 120Vac 60 , 1/4HP(3.9A)

Output Controller

NoteSpecificationComponent

Control of FND Display

1 Classification of FND Shape and Cell

Refer FND wiring diagram and dimension

Display

2526

3031

65 mode3740

4950

Always “On” regardless of temperature after main

power is “On”.

5859

6667

73 :Off / 69 :On6973

HeaterOffOnSegment

2 FND Operation

3.8 :Off / 7.0 :On7.0

3.8

Remarks

1110

1413

1817

2221

Always “On” regardless of temperature after main

power is “On”.

CompressorOffOnSegment

< HOT Temperature segment >

< COOL Temperature segment >

Page is loading ...

Coway CHP-01AL User manual

Coway CHP-01AL User manual

Coway CHP-01AL User manual

Related papers

Other documents