Vaisala Compact User Interface User manual

IM-EN-CI v. 2.00

Instruction Manual

Compact User Interface

CI

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

PUBLISHED BY

Vaisala Oyj

Vanha Nurmijärvene 21, FI-01670 Vantaa, Finland

P.O. Box 26, FI-00421 Helsinki, Finland

+358 9 8949 1

Visit our Internet pages at www.vaisala.com.

General safety consideraons

Warning! If this device is used against manufacturer’s instrucons, user safety may be

compromised.

Warranty

For standard warranty terms and condions, see www.vaisala.com/warranty.

Please observe that any such warranty may not be valid in case of damage due to nor-

mal wear and tear, exceponal operang condions, negligent handling or installaon,

or unauthorized modicaons. Please see the applicable supply contract or Condions

of Sale for details of the warranty for each product.

Technical support

Contact Vaisala technical support at [email protected]. Provide at least the fol-

lowing supporng informaon:

• Product name, model, and serial number

• Name and locaon of the installaon site

• Name and contact informaon of a technical person who can provide further infor-

maon of the problem

For more informaon, see www.vaisala.com/support.

Disposal

When wishing to dispose of an obsolete instrument or any parts of an in-

strument, please observe local and naonal regulaons and requirements

for the disposal of electrical and electronic equipment.

Symbols and terms used in this manual:

This indicates a warning. It provides safety precauon informaon needed to

avoid injury while operang the refractometer system.

This indicates that something is important for the operaon of the refractome-

ter system.

Note. Notes contain addional informaon and hints.

Compact user interface instrucon manual

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

Table of contents

1 Descripon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2 Mounng . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.1 Connecons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1.1 Refractometer cable connecon . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1.2 Ethernet cable connecon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.1 Refractometer connecon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 Acvang and removing apps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3 Conguring mA output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.4 Managing users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.5 Ethernet connecon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.1 Baery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5 Specicaons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5.1 Connector specicaons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

A EU declaraon of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

B Soware licence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

1 Descripon 1

1 Descripon

The Compact user interface CI is a compact, light-weight display for monitoring and

operang a Vaisala K-PATENTS® refractometer. It is ideal for applicaons where prism

wash and addional inputs/outputs are not needed. CI is is operated by the touch-

screen display. It is mainly intended for control room environment. There is a protecve

cover available for industrial environment. CI has IP66 rang. An epoxy coated version

of the CI is recommended for eld installaons.

Figure 1.1 Compact user interface CI

2 Compact user interface instrucon manual

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

2 Mounng

The Compact user interface CI can be mounted on a wall with a wall mounng adapter

or on a VESA 200x100 wall mounng arm, or on a table with a table stand. It also has

a panel mounng opon. The mounng locaon should be easily accessible.

Figure 2.1 Table stand

If the Compact user interface is installed in an industrial environment instead of a con-

trol room, a protecve display shield is recommended. To mount the display shield,

rst screw two M5x 12 DIN912 A2 screws in upper two holes of the CI frame. Then

install the hinges and shield to lower M5 holes with M5x12 ISO 14581 TX A2 screws.

2 Mounng 3

Figure 2.2 VESA wall mounng adapter

4 Compact user interface instrucon manual

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

275mm

195mm

152mm

296mm

Dia. 5.2 mm

142mm

226mm

Panel mounting dimensions.

Figure 2.3 Panel mounng opon

2 Mounng 5

CI-004

Figure 2.4 Display shield installaon

CI-005

1

2

1

2

Slide cover upwards to unslot

upper screw.

Then cover is free to swing forwards

to max. rotation of 180°.

Figure 2.5 Opening the display shield

6 Compact user interface instrucon manual

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

2.1 Connecons

PR-43

REFRACTOMETER

M-12-8 pin, A code, M

Unclassiﬁed area

PR-8430-____

Platform 4 cable

M12-8 pin, A-code, F+M

Ethernet, mA, 24V

Compact User Interface, CI

1 x M12-4 pin, D-code, F (External Ethernet)

1 x M12-8 pin, A-code, F (System)

1 x M12-4 pin, A-code, M (24VDC, mA)

M

F

max. 90m (295ft)

Refractometer with CI

OR

PR-8440-___

Ethernet cable for interfaces

M12-4 pin, D-code, M+M

Ethernet

M

max. 90m (295ft)

M

PR-8330-___

Ethernet cable for interfaces

M12-4 pin, D-code, M+RJ45

Ethernet

max. 90m (295ft)

PR-8350-010

Power-mA cable M12

M12- 4 pin, A-code, F

mA, 24V

F

10m (33ft)

Figure 2.6 CI connecons

2 Mounng 7

blue mA+

brown mA-

white VDD

black GND

Figure 2.7 Connecng CI to power

2.1.1 Refractometer cable connecon

The refractometer is connected to the CI with a Plaorm 4 cable PR-8430, a M12 male-

female 8 pins A-coded cable. Refractometer connecon can be made while the CI is

powered. The maximum length of the PR-8430 cable is 90 meters (295 ), but with a

Plaorm 4 cable extender PR-8660 another max. 90 meters long Plaorm 4 cable can

be added, bringing the maximum total length to 180 meters (590 ).

2.1.2 Ethernet cable connecon

If you wish to connect the CI with e.g. a laptop, you can purchase Interconnecng cable

PR-8330 with a M12-4-pin connector in one end and a RJ-45 connector in the other end.

The ethernet connecon is used to get access to the CI web pages.

8 Compact user interface instrucon manual

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

3 Use

Power up the CI. A startup display shows briey, then the CI goes into the Main display.

The CI is operated by tapping the touch screen. If you nd that the touch screen is

dicult to use with ngers, try tapping it with e.g. the blunt end of a pen or use your

nail instead of the whole ngerp. The screen works even when you are wearing gloves.

COMPACT USER INTERFACE CI

DISPLAYS

PR-43-A Process Refractometer 20

Main

Diagnostics Trend User authentication

Figure 3.1 Compact user interface displays

3 Use 9

Figure 3.2 Access applicaon data and conguraon by tapping applicaon window

3.1 Refractometer connecon

Refractometer’s connecon to the CI is congured under the tle Instrument in the

Sengs > Network menu. By default the refractometer’s IP address is congured via

BOOTP server running on the CI. To reconnect a refractometer you can just replug its

cable to the CI – the IP address is congured automacally. Refractometer connecon

can be made while the CI is powered.

3.2 Acvang and removing apps

The Main display may be empty even when a refractometer is connected to the CI. This

means that an applicaon must be acvated. Go to Sengs > Applicaons, tap on the

empty applicaon slot and select the app type and source for that slot. Aer choosing

sengs for the app, tap Done to exit the setup.

Note: Acvang Recipe app is not possible in the Compact user interface CI. Recipe

app requires external inputs provided by the Mulchannel user interface MI.

10 Compact user interface instrucon manual

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

The empty applicaon slot may contain an earlier app conguraon. In that case a dia-

log will open during app acvaon and the earlier app conguraon can be re-enabled.

If necessary the app can also be removed. Go to Sengs > Applicaons and tap Re-

move on the applicaon slot. Accept the removal by tapping Ok. The removed app’s

conguraon will be saved unl another kind of applicaon is added to the same slot.

Figure 3.3 Empty Main display. Tap Sengs to acvate an app

3 Use 11

Figure 3.4 Selecng an empty applicaon slot to acvate the app

Figure 3.5 Selecng a source to acvate the

app, here applicaon type Ref is already selected

12 Compact user interface instrucon manual

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

Figure 3.6 Selecng and empty applicaon slot

that contains old refractometer app conguraon

Figure 3.7 The earlier app conguraon can be re-enabled

3 Use 13

Figure 3.8 If necessary, the app can also be removed

3.3 Conguring mA output

To set the mA output values tap anywhere in the applicaon window and then select

Calibraon > Sensor. In the list, tap the parameter you want to change, type the new

numbers with the number pad and approve the change by tapping Done. Minimum

and maximum values set the measurement range. If your measurement unit is CONC%

and you want to measure the range 15–25 CONC%, the output signal for minimum 15

will be 4 mA and for maximum 25 it’ll be 20 mA. Default mA sets an mA default output

value that the refractometer returns to in certain situaons. The value can be set to a

low or high mA value, e.g. 3.0 mA or 22 mA.

14 Compact user interface instrucon manual

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

Figure 3.9 Select Sensor on Calibraon display to congure mA output

Figure 3.10 Congure the mA output parameters

3 Use 15

3.4 Managing users

Some funcons of the CI, e.g. calibraon, are only available to a user who is logged

into the system. The master user password is wrien on the delivery data sheet that is

shipped with the CI. However, K-Patents recommends that a user name and a password

is set separately for every user who needs to have frequent access to the restricted

funcons. Go to Sengs, then select Users to add and remove users. To add a new

user, tap + Add user. To remove a user, tap the name of that user, then Remove user.

Figure 3.11 Users display

3.5 Ethernet connecon

The CI has a built-in web server with a home page. The CI home page allows you to

browse les or upload an update or a license le. To access the CI web page use IP

address found under the tle Ethernet in the Sengs > Network menu.

The default IP address mode seng for the CI is Auto. In this mode the CI gets the

IP address from an external DHCP server. If that fails the IP address will fall back to a

stac IP seng. Alternavely IP address mode: Stac congures the CI to use a stac

IP address only. Aer choosing sengs for the network, tap Apply to save all sengs.

Aer factory reset the default IP address of the CI is 192.168.1.11.

16 Compact user interface instrucon manual

Document/Revision No. IM-EN-CI/2.00 Eecve: September 2, 2019

Figure 3.12 To access the CI web page use the

IP address found in the Sengs > Network menu

Figure 3.13 Steps to congure a stac IP address for CI

Page is loading ...

Vaisala Compact User Interface User manual

Vaisala Compact User Interface User manual

Related papers

Other documents