LED DESIGNER STRIPS V2
INSTALL INSTRUCTIONS
Specifications and dimensions are subject to change without notice.
Photos and line drawings may not be to scale and are for general reference only.© P.Q.L., Inc. • 2285 Ward Avenue • Simi Valley, CA 93065 • 800.323.8107 • Fax: 877.619.7053
PREMIUM QUALITY LIGHTING® • www.PQLighting.com
PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read
the instructions before you install and use the luminaire.
WARNING, CAUTIONS AND OPERATING INSTRUCTIONS
Before installing, servicing, or performing routine maintenance on this
equipment; Follow these general precautions:
• To reduce the risk of death, personal injury or property damage from
fire, electric shock, falling parts, cuts/abrasions, and other hazards read
all warnings and instructions included with and on the fixture box and all
fixture labels.
• Commercial installation, service and maintenance of luminaires should be
performed by a qualified licensed electrician.
• For the installation: If you are unsure about the installation or maintenance
of the luminaires, consult a qualified licensed electrician and check your
local electrical code.
• To prevent wiring damage or abrasion, do not expose wiring to edges of
sheet metal or other sharp objects.
• Do not make or alter any open holes in an enclosure of wiring or electrical
components during kit installation.
WARNING: RISK OF FIRE OR ELECTRICAL SHOCK
• Turn o electrical power at fuse or circuit breaker box before wiring fixture
to the power supply.
• Turn o the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire
label information.
• All wiring connections should be capped with UL approved wire
connectors.
CAUTION: RISK OF INJURY
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be
hazardous to children.
NOTICES:
• Green ground screw is provided in the proper location. DO NOT RELOCATE.
• Minimum 90° supply conductors.
• Suitable for Dry or Damp Locations.
!WARNING DISCONNECT POWER BEFORE INSTALLING OR SERVICING.
SURFACE MOUNTING FIG. :
1. Secure the provided brackets onto the ceiling using the provided
accessories and screws.
2. Screw the covers at the outlet of the back of the housing (Fig. 1).
3. Wire to main power through the J-Box (Fig. 2).
4. Then clip the brackets to the slots of the fixture (Fig. 3).
GENERAL WIRING DIAGRAM
LED DRIVER
Black (Line)
White (Neutral)
Green (Grd)
TO SOURCE
120-277V
Purple (Dim+)
Grey (Dim-)
Blue (-)
Red (+)
Lead wires
to LED
Load
** Dimming
wires to 0-10v IEC
Compliant Control
Fig. 2 Fig. 3Fig. 1
Outlet Box Cover
SUSPENDED CHAIN MOUNTING FIG. :
1. Clip the brackets to the slots of the fixture.
2. Attach the customer supplied V-hooks to the brackets (Fig. 4).
3. Attach the customer supplied chain to the V-Hooks and mounting
surface.
LENS INSPECTION: After installation check to make sure the lens is
completely secure inside the lamp body and the end cap. Gently pull
down on the lens to ensure it does not shift.
Fig. 4
Flexible Metallic Conduit
Bracket
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Superior Life PQL-55353 User manual
-
Sunco Lighting 2ft LED Vapor User manual
-
AcuityBrands CSS LED Strip Light User manual
-
Acuity Brands Lithonia Lighting XVML Operating instructions
-
Lithonia Lighting XVML LED Linear Installation guide
-
Lithonia Lighting Contractor Select CPHB LED High Bay Installation guide
-
RAB Lighting IVGT5-50L750WU/LCE2 Operating instructions
-
-
Lithonia Lighting CPHB 18LM MVOLT 50K Installation guide
-