2. Home
  3. Lighting
  4. Floodlights
  5. NOVALUX
  6. 55525
55525

NOVALUX 55525 User manual

  • Hello! I've reviewed the install instructions for the PQL LED NANOTECH PUREAIRE Troffer. This document details the installation process for both recessed and cable-suspended mounting, as well as how to use the remote control to adjust color temperature. I am also familiar with filter replacement recommendations and safety precautions.
  • What are the available color temperature options?
    How often should the filter be replaced?
    Can the color temperature be adjusted remotely?
LED NANOTECH PUREAIRE™ TROFFER
INSTALL INSTRUCTIONS
PREMIUM QUALITY LIGHTING® • www.PQLighting.com
© P.Q.L., Inc. • 2285 Ward Avenue • Simi Valley, CA 93065 • 800-323-8107
Specifications subject to change without notice. Photos and line
drawings may not be to scale and are for general reference only.
WARNING, CAUTIONS AND OPERATING INSTRUCTIONS
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings
and instructions included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
• For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local
electrical code.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
WARNING: RISK OF FIRE OR ELECTRICAL SHOCK
• Turn o electrical power at fuse or circuit breaker box before wiring fixture to the power supply or performing any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION: RISK OF INJURY
• Operating temperature: -4~122°F (-20~50°C)
• Suitable for damp locations.
PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the instructions before you install and use the luminaire.
WARNING - TURN OFF POWER SUPPLY FROM MAIN CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING.
!
FIELD ADJUSTABLE CCT
Choose preferred CCT using the remote control. Color options available are 3000K, 4000K or
5000K.
RECESSED INSTALLATION
1. Remove the ceiling tile where the fixture will be located. (Fig. 1)
2. Rotate troer 45 degrees to the grid, and carefully insert troer up into T-bar ceiling
grid. Secure safety cable to the back plate of the fixture as needed to meet local seismic
requirements. (Fig. 2) Safety cable requirement, cables, and method of attachment to the
building to be determined and provided by installer according to local building codes.
3. Turn the troer so the light panel is facing down and firmly seated in the T-Bar ceiling grid.
(Fig. 3)
4. Connect power supply as needed. Make sure that all the black wire is connected to Line,
the white wire is connected to Neutral, and the green wire is connected firmly to Ground
per NEC code. (See General Wiring Diagram)
Note:
• For proper installation, first check the size of opening compared to the dimensions of the
luminaire.
• Make sure all screws and connections are securely fastened.
Fig. 1
Fig. 2
Fig. 3
GENERAL WIRING DIAGRAM
LED DRIVER
Black (Line)
White (Neutral)
Green (Grd)
TO SOURCE
120-277V
LED NANOTECH PUREAIRE™ TROFFER
INSTALL INSTRUCTIONS
PREMIUM QUALITY LIGHTING® • www.PQLighting.com
© P.Q.L., Inc. • 2285 Ward Avenue • Simi Valley, CA 93065 • 800-323-8107
Specifications subject to change without notice. Photos and line
drawings may not be to scale and are for general reference only.
Fig. 4
CABLE SUSPENDED MOUNTING (Sold Separately, provided by installer)
1. Attach building mounting points and cables that will support at least 2.5x the weight of the
fixture.
2. Attach cables to the pre-drilled holes located in the square plate on top of the troer so
that the fixture hangs level. (Fig. 4)
3. Connect power supply as needed. Make sure that all the black wire is connected to Line,
the white wire is connected to Neutral, and the green wire is connected firmly to Ground
per NEC code. (See General Wiring Diagram, Page 1)
Note: Make sure all screws and connections are securely fastened.
Tab
Indicator Light
Reset
Fig. 5
WARNING - TURN OFF POWER SUPPLY FROM MAIN CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING.
!
Lamp
On/Off
Fan
On/Off
CCT 100%
75% 50%
25% Reset
Turns LED lights On or O
Changes color temperature
75% light output
25% light output
REMOTE CONTROL
• Battery Type: 2ea - AAA 1.5V
REMOTE CONTROL PAIRING TO FIXTURE
Using a dedicated wall switch or circuit breaker, power o the
fixture for >10+ seconds; then power the fixture back on and in the
first 3 seconds press the remote control’s Lamp ON/OFF button 3
times. If the fixture flashes 3 times, the pairing was successful.
PAIR CANCELLATION
Using a dedicated wall switch or circuit breaker, power o the
fixture for >10+ seconds; then power the fixture back on and in the
first 3 seconds press and hold down the Lamp ON/OFF button. If
the fixture flashes 6 times, the remote unpairing was successful.
REMOTE CONTROL MEMORY FUNCTION
When the fixture is shut o (with wall switch, breaker, or remote),
the last setting values used on the remote will be stored and will
resume when the fixture is turned back on.
Turns Fan On or O
100% light output
50% light output
Resets filters timing counter
Indicator Light
FILTER REPLACEMENT • Recommended every 2160 hours (Sold Separately, Item# 55523)
• When the indicator light is flickering or every 2160 hours, whichever comes first, replace filter
by lifting up on tab to remove old filter and replace with new. (Fig. 5)
• Use a pin to reset the timing counter (or use the remote control).
/