2. Altronix
  3. TROVE Keyscan
TROVE Keyscan

Altronix TROVE Keyscan Installation guide

  • Hello! I've reviewed the provided Altronix/Keyscan installation guide for T2KK3F8, T2KK3F8Q, T2KK3F8D, and T2KK3F8DQ access power controllers. This document details the pre-assembled kits, including the components like the Trove2 enclosure, power supplies, and various sub-assemblies. I'm ready to assist with any questions about these kits, their specifications, or installation procedures.
  • What components are included in the kits?
    What is the difference between kits with fused outputs and PTC outputs?
    What is the maximum number of doors these kits can handle?
T2KK3F8
8 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove2 enclosure with TKA2 Altronix/Keyscan backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) ACM8 - Fused Access Power Controller
- (1) T16100 Transformer
T2KK3F8Q
8 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove2 enclosure with TKA2 Altronix/Keyscan backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM8 - Fused Access Power Controller
- (1) T16100 Transformer
T2KK3F8D
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove2 enclosure with TKA2 Altronix/Keyscan backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) ACM8CB - PTC Access Power Controller
- (1) T16100 Transformer
T2KK3F8DQ
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove2 enclosure with TKA2 Altronix/Keyscan backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM8CB - PTC Access Power Controller
- (1) T16100 Transformer
Access & Power Integration
Altronix/Keyscan Kits
Models Include:
Rev. TKK072817
Installing Company: _________________________ Service Rep. Name: __________________________________________
Address: _________________________________________________________ Phone #: _________________________
All registered trademarks are property of their respective owners. More than just power.™
Installation Guide
All components of these Trove kits are UL Listed sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.
- 2 - T2KK Kits Installation Guide
Overview:
Altronix Trove Keyscan kits are pre-assembled and consist of Trove2KA2 enclosure/backplane with factory installed Altronix power supply/
charger, transformer, and sub-assemblies. These kits also accommodate various combinations of Keyscan boards for up to eight (8) doors in
a single enclosure.
Configuration Chart:
Altronix
Model
Number
Networkable
120VAC 60Hz
Input Current (A)
Power Supply Board
Input Fuse Rating
Power Supply Board
Battery Fuse Rating
Nominal DC
Output Voltage
Maximum Supply Current
for Main and Aux. Outputs
on Power Supply board
and ACM8/ACM8CB
Access Power Controller’s
outputs (A)
Fail-Safe/Fail-Secure or
Dry Form “C” Outputs
Fail-Safe/Fail-Secure
Outputs (auto-resettable)
Current Per
ACM8 Output (A)
Current Per
ACM8CB Output (A)
ACM8/ACM8CB Board
Input Fuse Rating
ACM8 Board
Output Fuse Rating
ACM8CB Board
Output PTC Rating
[DC] [Aux]
24VDC Output
Range (V)
24VDC Output
Range (V)
T2KK3F8 – 3.5 5A/
250V
10A/
32V
20.19-
26.4
20.19-
26.4 24VDC @ 5.8A 8 – 2.5 – 10A/
250V 2.5A –
T2KK3F8Q P3.5 5A/
250V
10A/
32V
20.19-
26.4
20.19-
26.4 24VDC @ 5.8A 8 – 2.5 – 10A/
250V 2.5A –
T2KK3F8D – 3.5 6.3A/
250V
15A/
32V
20.17-
26.4
20.28-
26.4 24VDC @ 5.8A – 8 – 2.0 10A/
250V – 2A
T2KK3F8DQ P3.5 6.3A/
250V
15A/
32V
20.17-
26.4
20.28-
26.4 24VDC @ 5.8A – 8 – 2.0 10A/
250V – 2A
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1. Remove backplane from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners.
Place the enclosure’s upper keyholes over the three upper screws. Install the three lower screws and
make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location,
opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately
2” from the right side (Fig. 1, pg. 2).
Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed
reporting device. To activate alarm signal open the door of the enclosure.
4. Mount Keyscan boards to backplane, refer to page 3.
5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB,
corresponding Sub-Assembly Installation Guide for ACM8(CB) and LINQ2,
and T16100 Installation Instructions for T16100 for further installation instructions.
Hardware:
Fig. 1
Tamper Switch
(included)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure
Nylon Spacer | Metal Spacer | Pan Head Screw | Lock Nut
T2KK Kits Installation Guide - 3 -
Keyscan
CA250B,
CA4500B
CA8500B
Keyscan
DPS15
Locknut
Keyscan
CIM
Keyscan
OCB8
Keyscan
OCB8
NC C NO NC C NO
AC FAIL BAT FAIL
TRIGGER
AC DCAC1
EOLNOGND
SUPERVISED RESET
+AUX-
- BAT +- DC +
L G N
OFF - 24V
ON - 12V
ON
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix
ACM8 (T2KK3F8(Q))
or
ACM8CB (T2KK3F8(D)Q)
Altronix - eFlow6NB
LINQ2 (T2KK3F8(D)Q)
Altronix
T16100
T2KK3F8(D)(Q): Configuration of Keyscan Boards
1. Mount appropriate Keyscan boards into the correct positions (Fig. 2, pg. 2) by postioning spacers over appropriate holes in the
backplane and depressing down on board to secure spacer to the backplane (Fig. 2b, pg. 2).
2. Fasten backplane to Trove2 enclosure utilizing pan head screws (provided).
Fig. 2
Plastic Spacer
pre-mounted into
Keyscan modules
Insert into
TKA2 or
TKA3 backplane
Fig. 2b
- 4 - T2KK Kits Installation Guide
Enclosure Dimensions (H x W x D approximate):
27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm)
6.75” (171.5mm)8.25” (209.5mm)
8.00” (203.2mm)
2.00” (50.8mm)
2.00” (50.8mm)
1.25” (31.8mm)
1.25” (31.8mm)
5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)
1.25” (31.8mm)
6.25” (158.8mm) 19.80” (502.9mm)
1.00” (25.4mm)
27” (685.8mm)
1.5”
(38.1mm)
2.00” (50.8mm) 2.00” (50.8mm)
3.5”(88.9mm) 3.5”(88.9mm)
21.50” (546.1mm)
5.25” (133.35mm) 5.25” (133.35mm)
6.25” (158.8mm)
1.25”
(31.8mm)
0.85” (21.6mm)
0.5625” (14.3mm)
2.415” (61.3mm)
0.685” (17.4mm)
1.77”
(45mm)
0.885” (22.5mm)
1.125” (28.3mm)
Knockouts
2.00” (50.8mm) 2.00” (50.8mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
web site: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IITrove2KA2 Kit Series I28U
MEMBER
/