Gossen MetraWatt METRAHit 29S Operating instructions

Brand: Gossen MetraWatt

Model: METRAHit 29S

Category: Measuring, testing & control

Type: Operating instructions

This manual is also suitable for

METRAHit 28S

METRA HIT 28S

METRA HIT 29S

Precision Digital Multimeter

3-348-851-03

13/2.06

Operation Instructions

2 GMC-I Gossen-Metrawatt GmbH

1LCD Display

2 MENU/ON|OFF ON / OFF key

Operating Mode Menu: Entry acknowledgment

3 DATA|CLEAR Function key for measurement value store,

delete and MIN-MAX

Operating Mode Menu: Individual menu item selection

reverse flux direction,

increase values

4 MAN|AUTO Manual measuring range selection key

Operating Mode Menu: Individual menu item selection

forward flux direction,

reduce values

5 ESC|FUNC Multifunction key

Operating Mode Menu: Exit menu level and

return to next highest level,

exit parameter entry mode

without storage of values

6 Rotary switch for measurement functions

7 Connection jacks

8 Power pack connection jack

9 DKD calibration mark

max. 600 V !

→ chapter 2

→ chapter 5

→ chapter 3

→ chapter 2

→ chapter 3

→ chapter 4

→ chapter 3

→ chapter 1

→ chapter 8f

GMC-I Gossen-Metrawatt GmbH 3

Digital Display Symbols

1 Main display with decimal point and indication of polarity

2 Sub-displays with decimal point and indication of polarity

3 Unit of measure

4 Selected current type

5 Continuous operation, symbol blinks for data transmission

6 Low battery

7 Acoustic signal on, buzzer activated for corresponding function

8 Zero balancing

9 Reference value

10 Memory display, “hold measurement value”

11 Stopwatch activated or elapsed time since start of measurement

12 Together with symbol 11:

elapsed time since activation of corresponding function, counter,

number of events when trigger threshold is exceeded

13 MIN-MAX storage

14 Event marking

15 Synchronized storage, METRA HIT 29S only

16 Memory mode, METRA HIT 29S only

17 Manual measuring range selection

18 Relative value

19 Measurement with clip-on current transformer active:

Factor 1000 or 10000 is considered

141517 16

13121098 11

4 GMC-I Gossen-Metrawatt GmbH

Contents Page

1 Safety Features and Precautions .................................... 6

2 Initial Start-Up ................................................................. 8

3 Selection of Measurement Functions and

Measuring Ranges ........................................................ 10

3.1 Automatic Measuring Range Selection .............................. 10

3.2 Manual Measuring Range Selection .................................. 10

3.3 Quick Measurements ....................................................... 11

4 Triple Digital Display ..................................................... 11

5 Measurement Value Storage

“DATA” (Hold & Compare) ............................................. 12

6 Minimum and Maximum Value Storage

“MIN-MAX” with Time Stamp ....................................... 14

7 Auto Select .................................................................... 16

8 Voltage Measurement ................................................... 17

8.1 Transient Overvoltages ..................................................... 18

8.2 Voltage Measurements for Greater than 600 V .................. 18

8.3 Alternating Voltage Level Measurement (dB) ...................... 19

9 Current Measurement ................................................... 21

9.1 Measurement with (Clip-On) Current Transformers ............ 22

9.1.1 Transformer Output mA or A for AC Measurements ........... 22

9.1.2 Transformer Output V for AC and DC Measurements ......... 23

10 Resistance Measurement .............................................. 24

11 Continuity Testing for Resistance Measurement .......... 25

12 Diode Testing ................................................................ 26

13 Continuity Testing for Diode Tests ................................ 27

14 Capacitance Measurement ........................................... 28

15 Frequency Measurement .............................................. 29

16 Temperature Measurement .......................................... 30

16.1 Temperature Measurement with Pt100 and Pt1000 .......... 30

16.2 Temperature Measurement

with Thermocouple and Reference Junction ...................... 30

17 Counting Events and Zero Crossings ............................. 32

17.1 Event Counting ................................................................ 32

17.2 Count Zero Crossings ...................................................... 34

18 Stopwatch ..................................................................... 34

19 Δ Operating Mode, Reference Value REF. ................... 36

GMC-I Gossen-Metrawatt GmbH 5

Page

20 Power Measurement with the METRA HIT 29S .............38

20.1 Power Measurement with Analog Signals I and V ...............38

20.2 Energy Measurement with Pulses .....................................40

20.3 EnErGY Menu for Energy Measurement ............................41

20.4 Exit Power/Energy Measurement .......................................42

20.5 Power Measurement with

(Clip-On) Current Transformers .........................................42

21 Line Fault Recording with the METRA HIT 29S ..............43

21.1 Line Fault Recording without Memory Mode ......................43

21.2 Trigger Parameters for Line Fault Recording ......................46

21.3 Line Fault Recording with Memory Mode ...........................47

22 Storing Measurement Values with the METRA HIT 29S 47

22.1 General Parameters .........................................................50

22.2 Trigger Functions .............................................................51

22.2.1 Trigger Function Parameters .............................................52

23 Setting the Measurement Parameters ...........................56

23.1 Description of General Parameters in the SEt Menu ..........58

23.1.1 Sampling Rate: rAtE . ......................................................58

23.1.2 Rapid Query: MenuCYCLE . .............................................58

23.1.3 tiME und Datum dAtE ........................................... 58

23.2 Parameter Description of Menu Item: inFo . .....................59

23.3 Default Settings ...............................................................59

23.4 List of All Parameters ......................................................60

24 Data Transmission via the RS 232 Interface .................61

24.1 Activating the Interface .....................................................61

24.2 Selecting Interface Parameters ......................................... 62

25 Characteristic Values .....................................................64

26 Maintenance ..................................................................74

26.1 Battery ............................................................................74

26.2 Power Pack .....................................................................75

26.3 Fuses ..............................................................................75

26.4 Housing ...........................................................................76

27 Multimeter Messages ...................................................76

28 Accessories ...................................................................77

28.1 General ...........................................................................77

28.2 Characteristic Values of Measuring Cables

(Scope of Supply of Safety Cable Set KS17-2) ...................77

29 Repair and Replacement Parts Service

DKD Calibration Lab

and Rental Instrument Service ......................................77

30 Warranty ........................................................................78

31 Product Support .............................................................79

6 GMC-I Gossen-Metrawatt GmbH

1 Safety Features and Precautions

You have selected an instrument which provides you with a

high level of safety.

This instrument fulfills the requirements of the applicable

European and national EC guidelines. We confirm this with

the CE marking. The relevant declaration of conformity can

be obtained from GMC-I Gossen-Metrawatt GmbH.

The precision digital multimeter is manufactured and tested

in accordance with safety regulations IEC 61010–1:2001/

DIN EN 61010–1:2001/ VDE 0411–1:2002. When used for

its intended purpose, safety of the operator, as well as that

of the instrument, is assured. Their safety is however not

guaranteed, if the instrument is used improperly or handled

carelessly.

In order to maintain flawless technical safety conditions,

and to assure safe use, it is imperative that you read the

operating instructions thoroughly and carefully before plac-

ing your instrument into service, and that you follow all

instructions contained therein.

For your safety, as well as for the protection of your instru-

ment, the multimeter is equipped with an automatic socket

blocking device. This is coupled to the rotary switch, and

only allows connection to the socket required for the

selected function. It also prevents the switching of the

rotary selector to disallowed functions when a measure-

ment cable is plugged into a socket. Exception METRA

HIT 29S: in switch position W/mA or W/A jack V remains

open for power measurement, in position W/A jack mA is

only partially covered or blocked.

Use for Intended Purpose:

– The multimeter described herein is a portable instrument

which can be held in one hand during measurements.

– Only such measurements are performed as described in

chapters 8 to 21.

– The measuring instrument including measuring cables

and plug-on test probes is only used within the measur-

ing category indicated under the heading "Electrical

Safety" on page 72 (refer to the table on page 7 for the

meaning of the measuring categories).

– The limits of the overload capacity may not be exceeded.

Refer to the Characteristic Values on page 66 and page

70 for the duration and values of the overload capacity.

– Measurements are only performed within the specified

ambient conditions. Refer to page 73 for the operating

temperature range and relative humidity.

– The measuring instrument is only used in accordance

with the specified protection type, see page 73.

Observe the following safety precautions:

• The instrument may only be operated by persons who

are capable of recognizing contact hazards and taking

the appropriate safety precautions. Contact hazards

exist anywhere, where voltages of greater than 33 V may

occur (effective value).

GMC-I Gossen-Metrawatt GmbH 7

• Avoid working alone when taking measurements which

involve contact hazards. Be certain that a second person

is present.

• The maximum allowable voltage between any given connector

jack (7) and earth is equal to 600 V, category III or to 300 V,

category IV.

• Be prepared for the occurrence of unexpected voltages

at devices under test (e.g. defective devices). For exam-

ple, capacitors can be dangerously charged.

• Make certain that the measurement cables are in flaw-

less condition, e.g. no damage to insulation, no interrup-

tions in cables or plugs etc.

• No measurements may be made with this instrument in

electrical circuits with corona discharge (high-voltage).

• Special care is required when measurements are made

in HF electrical circuits. Dangerous pulsating voltages

may be present.

• Measurements under moist ambient conditions are not

allowable.

• Be absolutely certain that the measuring ranges are not

overloaded beyond their allowable capacities. Limit val-

ues can be found in the table “Measuring Ranges” in

Chapter 25 „Characteristic Values“.

• All current ranges are equipped with fuses (Nominal volt-

age of fuse = 1000 V). The maximum allowable voltage

for the measuring current circuit (= rated voltage of the

fuse) is equal to 600 V AC/DC in the “mA” and “A”

ranges.

• In switch position AUTO SELECT, Ω, , °C and F, the instru-

ment may only be used in power installations when the electri-

cal circuit is protected with a fuse or circuit breaker up to 20 A,

and the nominal voltage of the installation does not exceed

600 V in order to provide protection also under single-fault con-

ditions (EN 61010-1).

Measuring Categories and their Meaning per IEC 61010-1

The measurement category and the relevant maximum

rated voltage (e. g. 600 V CAT III) which are shown on the

instrument casing apply to your measuring instrument.

CAT Definition

Measurements in electrical circuits not directly connected to the mains

system:

e. g. power systems in motor vehicles or aeroplanes,

batteries ...

Measurements in electrical circuits directly connected to the low-volt-

age system: via plug, e.g. in households, offices, laboratories ...

III

Measurements in facility installations:

stationary consumers, distributor connections, devices

attached to a distributor

Measurements at the source of low-voltage installations:

Meters, main terminal, primary overcurrent protection devices

8 GMC-I Gossen-Metrawatt GmbH

Meaning of symbols on the instrument

Warning concerning a point of danger

(Attention: observe documentation)

Earth

Continuous, doubled or reinforced

insulation

CAT III / IV Instrument for measurement category III or IV

VDE testing authority approval mark

CSA approval mark

(North American test authority)

Indicates EU conformity

DKD calibration mark (red seal):

Repair, Parts Replacement and Balancing

When the instrument is opened, voltage conducting parts

may be exposed. The instrument must be disconnected

from the measuring circuit for repair, replacement of parts

or balancing. If repair or balancing of a live, open instru-

ment is required, this may only be carried out by trained

personnel who are familiar with the dangers involved.

Errors and Extraordinary Strains

If it may be assumed that the instrument can no longer be

operated safely, it must be removed from service and

secured against unintentional use.

Safe operation can no longer be relied upon,

• if the instrument demonstrates visible damage,

• if the instrument no longer functions,

• after a long period of storage under unfavorable condi-

tions.

2 Initial Start-Up

Battery

Please refer to chapter 26.1 regarding correct battery

installation.

Attention!

Before opening the instrument, disconnect it from

the measuring circuit!

Serial number

GOSSEN METRAWATT Calibration Laboratory

Date of calibration

German Calibration Service – Calibration Laboratory

B0730

99-02

DKD-K-

19701

GMC-I Gossen-Metrawatt GmbH 9

Operation with mains adapter

(accessory equipment, not included as a standard feature)

During power supply via mains adapter NA5/600, the

inserted batteries are cut off electronically so that they

rmay remain in the instrument, see also chapter 26.2. If

rechargeable batteries are used, they must be charched

outside the instrument.

Switching the Instrument On Manually

➭ Press the ON key.

Activation is acknowledged with a brief acoustic signal.

As long as the key remains pressed, all segments of the

liquid crystal display (LCD) are active. The LCD is shown

on page 3. After the key is released, the instrument is

ready for operation.

Switching the Instrument On via PC

After transmission of a data block from the PC, the multim-

eter is switched on. See also chapter 24.

Automatic Activation/Deactivation

To extend battery life, the multimeter is switched on and off

automatically in the transmit and data storage modes pro-

vided the transmit/storage interval rate is set at ≥ 10 s.

Note!

☞

Electrical discharge and high frequency interference

can cause incorrect displays, and may block the

measuring sequence. To reset, switch the instru-

ment off, and then back on. If this procedure is

unsuccessful, briefly disconnect the battery from the

contact terminals.

Setting Time and Date

See Chapter 23.1.3, page 58.

Switching the Instrument Off Manually

➭ Press and hold the

key, until the display is deacti-

vated. Deactivation of the instrument is acknowledged

by two brief acoustic signals.

Automatic Shut-Off

Your instrument shuts itself off automatically, if the mea-

surement value remains constant for a long period of time

(maximum measurement value fluctuation: approx. 0.8%

of the measuring range per minute or 1 °C or 1 °F per

minute), and if none of the keys or the rotary switch are

activated for a period of 10 minutes. Deactivation of the

instrument is acknowledged by a brief acoustic signal.

Exceptions are as follows:

Event counting, count zero crossing, stopwatch, transmit

or memory mode, continuous operation, power measure-

ment and line fault recording.

Disabling of Automatic Shut-Off

The instrument can also be switched to “CONTINUOUS ON”.

➭ Simultaneously press the ON key and the multifunction

key ESC|FUNC when switching the instrument on. The

“CONTINUOUS ON” function is indicated at the LCD

with the symbol.

10 GMC-I Gossen-Metrawatt GmbH

3 Selection of Measurement Functions and

Measuring Ranges

The rotary switch is coupled to the automatic socket

blocking device, which makes two jacks available for each

function (except mA and A: 3 jacks. The jack for the “mA”

socket in the “A” function is half open). Before switching to

the “mA” or “A” functions, or out off the “mA” or “A” func-

tions, be certain that the plug has been removed from the

corresponding jack. The socket blocking device prevents

inadvertent switching to disallowed functions when a plug

connection exists.

3.1 Automatic Measuring Range Selection

The multimeter is equipped with automatic measuring

range selection for all measuring ranges, except for tem-

perature measurement and diode testing, as well as

respective continuity testing. This automatic feature is

active as soon as the instrument is switched on. The

instrument automatically selects the measuring range

which provides optimum resolution for the current mea-

sured quantity. The previously selected voltage measuring

range remains active after switching the instrument to fre-

quency measurement, events counting or count zero

crossing. The instrument is automatically switched to the

next highest or next lowest measuring range for the follow-

ing measured quantities:

2800 digits apply when switching from 300 kHz to 30 kHz.

3.2 Manual Measuring Range Selection

The automatic measuring range feature can be deactivated

and the ranges can be manually selected and prescribed

according to the following table.

The manual mode is deactivated by pressing and holding

the MAN|AUTO key (approx. 1s), by activating the rotary

switch or by switching the instrument off and back on again.

Measuring Range

Reso-

lution

Switching to the Next

Highest Range

at ±(... d + 1 d)

Switching to the Next

Lowest Range

at ±(... d -1 d)

V , mA , Ω, Hz

5 ¾ 310,000 28,000

V, V, A, mA,

A , 30 mF

4 ¾ 31,000 2,800

3 nF ... 3 mF 3 ¾ 3,100 280

⇓

MAN/

AUTO

Function

Acknowledge

Display

Acoust.

Signal

Brief Manual Mode Active: selected measuring range is fixed MAN 1 x

Brief

Switching Sequence for:

V: 300 mV → 3V→ 30 V → 300 V → 600 V → 300 mV

→ ...

dB: same switching sequence as for V

mA : 300 μA → 3mA→ 30 mA → 300 mA → 300 μA ...

A: 3A→ 10 A → 3 A ...

Ω:30MΩ→ 300 Ω→ 3kΩ→ 30 kΩ→ 300kΩ→

3MΩ→ 30 MΩ ...

F: 3nF→ 30 nF → 300 nF → 3 μF → 30 μF →

300 μF → 3000 μF → 30000 μF → 3 nF...

Hz: 300 Hz → 3kHz→ 300 kHz → 300 Hz ...

MAN 1 x

Long Return to Automatic Range Selection — 2 x

GMC-I Gossen-Metrawatt GmbH 11

3.3 Quick Measurements

If you wish to perform quicker measurements than those

possible with the automatic measuring range selection

function, make sure to establish the appropriate measuring

range:

•by manual measuring range selection, i. e. by selecting

the measuring range with the best resolution, see

chapter 3.2.

•via DATA function, see chapter 5. After the first measure-

ment, the proper measuring range will be automatically

determined so that measurements are performed

more rapidly from the second measured value

onwards.

With both functions, the established measuring range is

maintained for the subsequent series mode measurements.

4 Triple Digital Display

The three digital displays, one main display and two sub-

displays, show the measurement value with correct deci-

mal point and sign. The selected unit of measure and the

current type are also displayed. A minus sign appears in

front of the number for the measurement of zero-frequency

direct quantities, if the positive pole of the measured quan-

tity is applied to the “⊥” input.

“OL” (overload) is displayed, if the actual value falls below

the measuring range lower limit for the following measured

quantities:

V DC, I DC, Ω, Hz: 309999

V (AC, AC+DC), I (AC+DC), dB (V), 30 mF: 30999

W, VA, VAr, Wh (METRA HIT 29S): 30999

3 nF ... 3 mF: 3099

Refreshing of the digital display occurs at different intervals

for the various measured quantities (see display update

page 71).

Although the main display is activated immediately after the

multimeter is switched on, the two sub-displays must be

activated with the DATA|CLEAR key. This prevents the contin-

uous display of an undefined condition which was present

at the start of measurement, e.g. open-circuit, as a maxi-

mum value.

015.000

013,000 018,000

Sub-Display: MIN

Main Display

Sub-Display: MAX

12 GMC-I Gossen-Metrawatt GmbH

5 Measurement Value Storage

“DATA” (Hold & Compare)

Measurement values can be automatically “frozen” with the

DATA (Hold) function. This can be especially useful when

your full attention is required for testing the measuring

point with the test probes.

After the measurement value has been acquired, and the

appropriate “condition” has been fulfilled according to the

following table, the measurement value is displayed in the

left hand sub-display and two acoustic signal sounds. At

the same time “MAN” appears and indicates that the mea-

suring range is now set. The test probes can now be

removed from the measuring point and the measurement

value can be read from the sub-display. If the measure-

ment value lies below the limit value shown in the table, the

instrument is reactivated for the storage of a new value; the

“DATA” display blinks.

Comparison of measurement values (DATA Compare)

If the newly stored measurement value deviates less than

0.33% of the measuring range from the first measurement

value, the acoustic signal (DATA Compare) sounds twice. If

it deviates more than 0.33 % from the measuring range,

only a brief signal sounds.

DATA

Acoustic Signal

015.000

015.010

015,000

GMC-I Gossen-Metrawatt GmbH 13

Reactivation when actual value falls below prescribed limit value

Relative to alternating voltage values

Also applies to continuity testing

When a measurement value is stored for the first time as a reference value,

the acoustic signal sounds twice. For subsequent storage of the same mea-

surement value, the acoustic signal sounds only twice if the subsequently

stored measurement value deviates from the first value by less than 0.33%

of the measuring range dependent upon resolution.

Exception: 10% at 300 Ω or 3 nF

Abbreviations

MR = Measuring range

As long as the DATA function is active, the measuring

ranges should not be changed manually.

The DATA function is deactivated if the DATA|CLEAR key is

pressed and held (approx. 1 s), if the rotary switch is acti-

vated or if the instrument is switched off and back on

again.

Function

DATA

⇓

DATA

Condition Response at Instrument

Measuring

Function

Measurement

Value

Sub-Display

Acoustic

Signal

Meas.

Value

DATA

Switch on brief

dis-

played

brief

Store

(stabilized mea-

surement value)

V, d B

, A

F, Hz

> 3.3%

of MR

dis-

played

brief

Reactivate

V, d B

, A

F, Hz

< 3.3%

of MR

stored

meas.

value

blinks

3),

Switch to

function

MIN/MAX

brief see Table chapter 6

Quit long

deleted

14 GMC-I Gossen-Metrawatt GmbH

6 Minimum and Maximum Value Storage

“MIN-MAX” with Time Stamp

Minimum and maximum values can be read out at the sub-

displays for long-term observation of measured quantities.

➭ If the DATA|CLEAR key is activated twice, current MIN and

MAX values are displayed at the sub-displays.

➭ Press the DATA|CLEAR key again to display the MIN value

and the time of occurrence.

➭ If the DATA|CLEAR key is once again activated, the MAX

value and the corresponding time of occurrence are dis-

played.

MIN and MAX values are deleted by pressing and holding

the DATA|CLEAR key (approx. 1 s), by activating the rotary

switch or by switching the instrument off and back on

again.

Note!

☞

No new MIN-MAX values are determined for

2 seconds after a change of measuring range, so

that measurement values can stabilize.

Function

MIN/MAX

⇓

DATA

MIN and MAX

Measurement Values/

Time of Measurement

Reaction at Instrument

Display

Acoust

Signal

Main Display

Sub-

Displays

Store

2 x brief

are stored

current

measurement

value

MIN and

MAX

1 x

Store and

display

brief

are stored

t and MIN 1 x

brief t and

MAX

1 x

Return to 1. brief are stored same as 1.

same as

1 x

Cancel

long

are deleted is deleted is deleted 2 x

GMC-I Gossen-Metrawatt GmbH 15

CLEAR

long

DATA

brief

DATA

brief

DATA

brief

DATA

brief

MIN MAX

tMIN MIN

tMAX MAX

Current

DATA

brief

09:20:05

015.000

015.345

015.986

015.123

015.345

015.678

015.986

Measurement Value

Current

Measurement Value

Current Meas. Value

16 GMC-I Gossen-Metrawatt GmbH

7Auto Select

In the Auto Select switch position, the auto-select function

(automatic selection of measuring function) allows for

autonomous recognition of the measured quantity, which is

applied between earth and the voltage jacks.

An overview of possible measured quantities as well as the

respective prerequisites for recognition can be found in the

AUTO SELECT table on page 67.

Note!

☞

Diodes must be connected from the anode side (“+”

pole) to the jack.

For polarized capacitors, the “+” pole must be con-

nected to the “F” jack and the “–” pole to the

“⊥”

jack.

Resistors and semiconductor paths connected in

parallel to the capacitor distort measurement

results!

➭ Set the rotary switch to AUTO SELECT.

Attention!

In the auto-select function, no more than 600 V

TRMS

may be applied between “⊥” and “V” jacks.

➭ Connect the measurement cables as shown. The “⊥”

jack should be grounded.

Note!

☞

The following chapter contains more information

concerning individual measured quantities.

0PEn

600V

F °C

GMC-I Gossen-Metrawatt GmbH 17

8 Voltage Measurement

➭ Depending upon the voltage to be measured, set the

rotary switch to V , V or V .

➭ Connect the measurement cables as shown. The “⊥”

jack should be grounded.

Note!

☞

In the 600 V range, an intermittent acoustic signal

sounds alarm if the measurement value exceeds

1000 V.

Attention!

Make absolutely certain that neither of the current

ranges (“mA” or “A”) is active when the multimeter is

connected for voltage measurements! If the fuse trip

limits are exceeded due to operator error, both the

operator and the instrument are in danger!

Zero Balancing in the 300 mV Measuring Range

➭ Select the 300 mV measuring range.

➭ Connect the measurement cables to the instrument, and

connect the free cable ends to one another.

➭ Briefly press the multifunction key ESC|FUNC.

015.000

600V

F °C

– (+)

+ (–)

18 GMC-I Gossen-Metrawatt GmbH

The instrument acknowledges zero balancing with an

acoustic signal and “

000.000” (± 1 digit) and the “ZERO”

symbol appear at the LCD. The voltage which was dis-

played at the moment the key was activated serves as a

reference value (max. ±20000 digits). It is automatically

subtracted from subsequently measured values.

➭Zero balancing can be deleted:

– by pressing and holding the multifunction key

ESC|FUNC

after which deletion is acknowledged with a twice

repeated acoustic signal,

– by switching the instrument off.

8.1 Transient Overvoltages

The multimeters are protected against transient overvolt-

ages of up to 6 kV with a halftime value for front time of

1.2/50 μs. Due to the fact that overvoltages of greater

duration can be expected for measurements at transform-

ers or motors etc., we recommend our KS30 measuring

adapter. It provides protection against transient overvolt-

ages of up to 6 kV with a halftime value for front time of 10/

1000 μs. Continuous loading capability is equal to

1200 V

TRMS

. Additional influence error due to use of the

KS30 measuring adapter amounts to approximately –2%.

8.2 Voltage Measurements for Greater than 600 V

Voltages of greater than 600 V can be measured with a

high-voltage probe, e.g. the HV3 (3 kV) or the HV30

(30 kV DC) of GMC-I Gossen-Metrawatt GmbH. The earth-

ing terminal must be connected to ground for measure-

ments of this type. Observe all required safety precautions!

000.000

Voltage Measurement > 600 V

with HV3 High-Voltage Probe

Black

Red

x1000

x100

GMC-I Gossen-Metrawatt GmbH 19

8.3 Alternating Voltage Level Measurement (dB)

The voltage level measurement is

used for determining the overall

damping or gain of a transmission

system (shown here as a two-port

network).

Voltage level [dB]

with V

= V

REF

(reference level rEF

vALUE

)

result > 1: gain; result < 1: damping

➭ Set the rotary switch to V .

➭ Briefly press the multifunction key ESC|FUNC.

The level measurement function is now active. The mea-

surement value is calculated from the effective value of the

alternating voltage component dependent upon the mea-

suring range (300 mV ... 600 V), and is displayed. The

default setting for the reference level is 0 dB = 0.775 V

(1 mW at 600 Ω) and appears in the left hand sub-display.

This value can be changed in the Setup menu:

SEt ↵ V rEF

vALUE

↵ V unit dB ↵ XXX.XXX V/dB VU↵.

Note!

☞

No matching resistors have been installed into the

instrument. It takes measurements with a high input

resistance of 5 MΩ. Input resistance for voltage mea-

surement is listed under technical data. In order to

perform correct measurements at non-terminated

devices under test, a matching resistor must be con-

nected to the terminals. Observe power dissipation at

the matching resistor!

600V

F °C

= max. 1 kV

Voltage Measurement with

the KS30 Measuring Adapter

------log⋅=

20 GMC-I Gossen-Metrawatt GmbH

Alternating voltage applied to the jacks appears at the right

hand sub-display.

➭ The alternating voltage measuring range is selected with

the MAN|AUTO key.

➭ The measurement value storage function for dB is made

available by pressing the DATA|CLEAR key.

➭ If the DATA|CLEAR key is pressed again, the normal display

for dB with MIN/MAX values appears.

➭ If the ESC|FUNC and MAN |AUTO keys are pressed simulta-

neously, the actual measurement value becomes the ref-

erence value. The instrument returns to the first display

with the measurement value as reference level.

➭ If the ESC|FUNC multifunction key is activated repeatedly,

the instrument is switched to frequency measurement,

event measurement, voltage measurement and finally

back to level measurement.

The dB ranges are listed under technical data.

FUNC

brief

Reference Level Alternating

Voltage

Level

DATA

brief

DATA

brief

Stored

Level

011.75

011.50

0.7750 3.0000

011.50

011.00 012.00

Page is loading ...

Gossen MetraWatt METRAHit 29S Operating instructions

Brand: Gossen MetraWatt

Model: METRAHit 29S

Category: Measuring, testing & control

Type: Operating instructions

This manual is also suitable for

METRAHit 28S

Download PDF

report

Gossen MetraWatt METRAHit 29S Operating instructions

This manual is also suitable for

Gossen MetraWatt METRAHit 29S Operating instructions

Related papers

Other documents