HySecurity StrongArm Crash Wireless Photo Eye Installation guide

HySecurity
Brand
HySecurity
Model
StrongArm Crash Wireless Photo Eye
Category
Gate Opener
Type
Installation guide
Page 1
www.hysecurity.com © 2014 P/N MX002552 D0604 Rev A
Installation Instructions
MX002552
StrongArm CRASH Integrated Wireless Photo Eye
Catch post
Access panel
Use a 7/32-inch
hex key.
Photo eye opening
for thru beam
To open the case, use a
phillips head screwdriver to
remove the screw. Replace
batteries, if necessary.
Access panel
Wireless photo eye
Bracket
Use a phillips head screwdriver.
Align opening on the
photo eye case with
opening on access
panel.
NOTE: Replace batteries with two lithium AA batteries.
e polarity on both batteries is in the same direction.
e wireless photo eye bracket and
access panel is attached to the catch
post with two hex head screws. When
installing the wireless photo eye or
replacing its batteries, follow the steps
shown in the illustrations.
Photo Eye
Alignment
Most photo eyes require careful optical
alignment in order to aim the emitter
beam to the center of the receiver. In
order to avoid false triggering, it is
important to carefully align the system.
HySecurity provides a unique feature
that turns power on to the photo eyes
and causes a buzzer to chirp when the
photo eye enters and exits alignment.
Align the photo eyes using this feature
by following the steps, on the next page:
12
2
12
1
12
3
12
4
Page 2
www.hysecurity.com © 2014 P/N MX002552 D0604 Rev A
Photo Eye Alignment, continued
1. Move the barrier arm o (away from) the close limit.
2. Access the User menu by pressing the Menu/Program button twice. Press Next
until menu item Photo Eye, (PE) appears.
3. Press Select and, using the Next button, change the display to PE 1.
4. Press Select again, and then Menu/Program.
5. Align the photo eyes. Note that the buzzer will chirp twice when the beam
is in alignment (not broken). However, the buzzer chirps once when the
photo beam is not aligned. When the buzzer chirps twice, you’re done! (e
parameter automatically resets the PE setting to zero the next time the barrier
arm closes.)
SuperviSed ConneCtion
e photo eye integrated into the pivot and catch posts has a true NC output (one
that is NC when the photo eye is powered, aligned and set for Light Operate). It
is a “monitored connection.” A monitored connection tests for the presence and
correct operation of the photo eye prior to each gate activation and prevents gate
operation if any fault is present.
photo eye FunCtion
If the gate is stationary, a tripped photo eye will prevent the gate from starting in
either direction. If tripped while closing, the standard function is to pause the gate
motion and then automatically restart again if the photo eye is clear within ve
seconds. An optional setting in the Installer Menu will cause a 2 second reversal of
travel while closing.
If the photo eye is tripped while opening, the arm continues to travel open without
interruption. For more information, refer to EC and EO shown in the Installer
Menu Table in the M30/M50 Programming and Operations manual.
StrongArm M30 shown
CLEAR OPENING
Integrated photo eye line of sight
STOP BUTTON
OPEN BUTTON
CLOSE BUTTON
REMOTE OPEN AND
RADIO CONTROL
OPEN/CLOSE
1
OPEN PARTIAL
INTERLOCK OPEN
TIME CLOCK OPEN
FREE EXIT DETECTOR
DISABLE EXIT DETECTOR
DISABLE CLOSE TIMER
INSIDE OBSTRUCTION
VEHICLE DETECTOR
OUTSIDE OBSTRUCTION
VEHICLE DETECTOR
SHADOW/RESET
VEHICLE DETECTOR
EDGE SENSOR
PHOTO EYE POWER
24 VOLTS COMMON
PHOTO EYE POWER
DO NOT USE
PHOTO EYE
OPEN DIRECTION
DO NOT USE
PHOTO EYE
CLOSE DIRECTION
DO NOT USE
CHARGER
AC LOSS
SPARE INPUT
EMERG CLOSE
FIRE DEPT OPEN
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
Smart Touch Controller
LIMIT DUAL GATE RADIO OPTIONS
DRIVE POWER RS485
MOTOR USER 1 USER 2
USER 3
VEHICLE DETECTORVEHICLE DETECTORVEHICLE DETECTOR
STOP/BUZZER
FREE
EXIT
INSIDE
OBSTR
OUTSIDE
OBSTR
SHADOW
RESET
WIEGAND
HySecurity
COM
NO
MX000585
VERSION
S/N
RS232
DISPLAY
VEHICLE DETECTOR
COM COMA B
RPM
COMOPEN EDGE+24V +24V
STAT US
LED
24V AC Acce
s
sory power
+
24V D
C
Power Connector
Power Module
COMMON
Photo eye
connecons in
StrongArm M30/M50
RED to
+ 24V
Black & White
both wires
to 14 (or 15)
Brown
to 19
PC1
  • Page 1 1
  • Page 2 2

HySecurity StrongArm Crash Wireless Photo Eye Installation guide

HySecurity
Brand
HySecurity
Model
StrongArm Crash Wireless Photo Eye
Category
Gate Opener
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents