Commell CMB-570 Installation guide

CMB-570 Installation Guide

9

CMB-570

Mini Barebone system

Intel High Performance Platform

Installation Guide

Edition 1.0

2008/03/06

CMB-570 Installation Guide

2

Document Content:

 Packing List

 Product Specification

 Hardware Installation

Packing List:

CMB-570 Chassis x 1

(Including LS-570 Motherboard)

DSPD-080-12A 80W AC-DC Adapter x 1

Power Cord x 1

CPU Cooler x 1 ATAPI Power Cord x1

44-pin to 44-pin ATA33 IDE Cable x1 (12CM)

DVI module with DVI Cable x 1

Serial port Cable x 3

USB Cable x 1

Audio Cable x1

Printer Cable x 1

PS/2 Keyboard & Mouse Cable x 1

CD Driver x1

CMB-570

CMB-570 Installation Guide

3

Hardware Installation:

Motherboard placement

MINIPCI

IDE

CN_IR

CN_LPT

CN_DVI

FDD

PCI

CN

_

DIO

CN_AUDIO

CN_COM2/3/4

CD_IN

SATA1/2

SYSFAN

DDRII_A/B

JAT

CN_PS2

CN_USB1/2

DC_OUT

CPUFAN

JFRNT

CN_INV

CN_LVDS

CN_HDTV

For the Components placement,it is available for LS-570

For Connector

For Jum

p

er

JCFSEL

JRTC

JCSEL1

JCSEL2

JVLCD

JCRT

CMB-570 Installation Guide

4

I/O panel:

Front:

USB

Power ButtonReset Button

HD LED

Power LED

CMB-570 Installation Guide

5

Rear:

DC-IN

USB1/2

COM1

Printer Mouse Keyboard

Line-In

Line-Out

Mic Phone

RJ45

VGA

COM2/3/4

DVI

USB3/4

CMB-570 Installation Guide

6

 Chassis Setup procedure:

1. Screw off as indication of the picture below.

Rear:

Top:

CMB-570 Installation Guide

7

2. Push the Chassis shield towards the back then open it.

1

CMB-570 Installation Guide

8

3. Screw off as indication of the picture below.

4. Turn the CPU cooler screws and then refer the motherboard manual

page.17 to install the CPU.(After installing CPU, please turn the CPU FAN

screws to tighten.)

CMB-570 Installation Guide

9

6. Open the DIMM holder then check the pin number to match the socket side

well before installing memory module.

7. Press down the memory module then check DIMM holder hook well.

CMB-570 Installation Guide

10

8. Put on HDD driver into HDD holder then turn the HDD drive screws to

tighten.(If you don’t have HDD drive please direct to step.10)

9. Connect IDE cable from motherboard to the HDD drive.

CMB-570 Installation Guide

11

10. Screw on as indication of the picture below Turn the screws.

11. Push the Chassis shield towards the back then open it.

1

CMB-570 Installation Guide

12

12. Screw on as indication of the picture below.

Rear:

Top:

CMB-570 Installation Guide

13

13. Finish.

CMB-570 Installation Guide

14

 CF card Setup Procedure:

1. Screw off as indication of the picture below.

2. Open it and you shall see CF card socket. As shown in the illustration,

face the label side toward you and insert the end with the small holes

into the Motherboard.

CMB-570 Installation Guide

15

3. Follow the foolproof design then insert the CF card.

4. Check connected well

CMB-570 Installation Guide

16

5. Close it shield and turn screw to tighten.

CMB-570 Installation Guide

17

Addendum Notice

Please leave the JCFSEL as 1-2 for Master mode, and set the IDE2 HDD

as Slave mode if you need to use the CF card.

Jumper: JCFSEL

Type: onboard 3-pin header

JCFSEL Mode

1-2 Master

2-3 Slave

Default setting

JCFSEL

1

3

CMB-570 Installation Guide

18

Contact Information

Any advice or comment about our products and service, or anything

we can help you please don’t hesitate to contact with us. We will do

our best to support you for your products, projects and business

Taiwan Commate Computer Inc.

Address

19F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih

Taipei Hsien, Taiwan

TEL +886-2-26963909

FAX +886-2-26963911

Website

TUhttp://www.commell.com.twUT

E-Mail

TU[email protected]UT (General Information)

TU[email protected]UT (Technical Support)

Commell is a brand name of Taiwan Commate Com

p

uter Inc.

Commell CMB-570 Installation guide

Commell CMB-570 Installation guide

Related papers

Other documents