Greenheck 452723 WD Series End Switch Kit Operating instructions

Greenheck
Brand
Greenheck
Model
452723 WD Series End Switch Kit
Type
Operating instructions

Greenheck 452723 WD Series End Switch Kit

The Greenheck 452723 WD Series End Switch Kit is designed for use with Greenheck's WD Series Dampers. It can be used in conjunction with MP-100, MP-200, and MP-300 series actuators.

The end switch kit allows you to wire the damper to a fan or light, so that the fan or light will only turn on when the damper is fully open. This can be useful for ensuring that the damper is fully open before the fan starts, or for using the end switch to delay the start-up of ECM fan motors (electronically commutated motors).

Greenheck 452723 WD Series End Switch Kit

The Greenheck 452723 WD Series End Switch Kit is designed for use with Greenheck's WD Series Dampers. It can be used in conjunction with MP-100, MP-200, and MP-300 series actuators.

The end switch kit allows you to wire the damper to a fan or light, so that the fan or light will only turn on when the damper is fully open. This can be useful for ensuring that the damper is fully open before the fan starts, or for using the end switch to delay the start-up of ECM fan motors (electronically commutated motors).

Document Number 452723
End Switch Kit for use on
WD Series Dampers
Field Installation Instructions for End Switch Kit Number 851038
These instructions apply to the field installation of end switch kits on Greenheck’s damper series WD. These end
switch kits can be used in conjunction with MP-100, MP-200, and MP-300 series actuators.
Common
L
1
Wiring Illustration
End
Switch
M
Green
Fan or
Light
N.C.
N.O.
L
2
Damper
Actuator
Note: Some actuators are multi-tap, use correct
connections per actuator wiring diagram.
Optional transformer for
277, 380, 575 or 600 volts
(120V actuator required)
Optional transformer for
277, 380, 575 or 600 volts
(120V actuator required)
Blue
24V Single Voltage Actuator
460V Single Voltage Actuator
White
Brown
Brown
110/115/120V Dual Voltage Actuators
Blue
208/220/230/240V Dual Voltage Actuators
Alternative wiring diagram
End switches are typically wired to a fan and/or to a
light serving as an open/not open indicator. When the
damper is powered open, one of the damper blades
makes contact with the spring rod of the end switch
which in turn makes a connection allowing power to
flow to the fan and/or light. This set up would be used
when it is desirable to ensure that the damper is fully
open before the fan starts.
When the end switch is utilized to delay start up of
ECM fan motors (electronically commutated motor)
a magnetic fan starter is required.
End Switch Kit for WD Series 1
®
Instructions
1. Position end switch such that the back side of
damper blade trips the spring rod.
2. Mount end switch bracket to the damper frame or
ductwork using #10 x
1
⁄2 in. self-drilling sheet metal
screws.
Part # Qty. Description
1 1 End switch mounting bracket
2 1 End switch
UL/CSA Rating L67
15 Amps: 125, 250, or 480 VAC
0.25 Amps: 250 VDC
0.50 Amps: 125 VDC
3 2 #6-32NC x 1½ in. machine screws
with nuts (packaged in end switch
housing)
4 2 #10 x ½ in. self-drilling sheet metal
screws
End Switch Installation on WD-100
Series Dampers
End Switch Installation on WD-200 &
300 Series Dampers
Damper Frame
1
⁄2 in.-14 NPSM
Damper
Blade
Damper
Tie Bar
Damper Frame
1
⁄2 in.-14 NPSM
Damper
Blade
Damper
Tie Bar
Spring Rod
Spring Rod
2
3
3
4
1
2
3
3
4
1
Damper Frame
1
⁄2 in.-14 NPSM
Damper
Blade
Damper
Tie Bar
Damper Frame
1
⁄2 in.-14 NPSM
Damper
Blade
Damper
Tie Bar
Spring Rod
Spring Rod
2
3
3
4
1
2
3
3
4
1
• 452723 End Switch Kit Rev. 9, September 2020 Copyright 2020 © Greenheck Fan Corporation
As a result of our commitment to continuous improvement, Greenheck reserves the right to change
specifications without notice.
Specific Greenheck product warranties are located on greenheck.com within the product area tabs and in
the Library under Warranties.
Phone: (715) 359-6171 • Fax: (715) 355-2399 • E-mail: [email protected] • Website: www.greenheck.com
Our Commitment
  • Page 1 1
  • Page 2 2

Greenheck 452723 WD Series End Switch Kit Operating instructions

Greenheck
Brand
Greenheck
Model
452723 WD Series End Switch Kit
Type
Operating instructions

Greenheck 452723 WD Series End Switch Kit

The Greenheck 452723 WD Series End Switch Kit is designed for use with Greenheck's WD Series Dampers. It can be used in conjunction with MP-100, MP-200, and MP-300 series actuators.

The end switch kit allows you to wire the damper to a fan or light, so that the fan or light will only turn on when the damper is fully open. This can be useful for ensuring that the damper is fully open before the fan starts, or for using the end switch to delay the start-up of ECM fan motors (electronically commutated motors).

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents