Gamber-Johnson 7160-0260 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0260
Type
Installation guide

This manual is also suitable for

Gamber-Johnson 7160-0260 is a vehicle base designed for the Ford Fusion 2013+. It can be easily installed without drilling, providing a secure mounting platform for various accessories. The base features offset riser compatibility, allowing for the attachment of additional equipment. Its sturdy construction ensures reliable support for devices, enhancing functionality and convenience within the vehicle.

Gamber-Johnson 7160-0260 is a vehicle base designed for the Ford Fusion 2013+. It can be easily installed without drilling, providing a secure mounting platform for various accessories. The base features offset riser compatibility, allowing for the attachment of additional equipment. Its sturdy construction ensures reliable support for devices, enhancing functionality and convenience within the vehicle.

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
4X 3/8 Spring Lock Washer
4X 3/8 Flat Washer
Offset Riser
4X 3/8-16 x .75 Cap Screw
Mounting Slots
Figure 1
Rev.C
INST-487
8. Secure the Offset Riser to the base.
The purpose of this instruction sheet is to illustrate the manufacturer’s recommended
INSTALLATION INSTRUCTIONS
Product Revision
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Printing Spec:
PS-001
FORD FUSION 2013+
Form
method of installing the Ford Fusion 2013+ vehicle base. The base requires no drilling.
7160-0260 Vehicle Base
© Copyright 2013 Gamber-Johnson, LLC
Installation
1. Remove the seat bolts located at the front of the
passenger seat.
2. Loosen but do not remove the seat bolts at the
back of the passenger seat.
3. Orient the base with the bent flange towards the
front of the vehicle.
4. Slide the base between the seat legs and the
vehicle floor pan (see Figure 2).
5. Align the slots of the base with the mounting holes
on the seat and vehicle floor.
6. Re-insert the bolts that were removed in STEP 1.
7. Tighten all four (4) seat bolts securing the
passenger seat.
Figure 2
  • Page 1 1

Gamber-Johnson 7160-0260 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0260
Type
Installation guide
This manual is also suitable for

Gamber-Johnson 7160-0260 is a vehicle base designed for the Ford Fusion 2013+. It can be easily installed without drilling, providing a secure mounting platform for various accessories. The base features offset riser compatibility, allowing for the attachment of additional equipment. Its sturdy construction ensures reliable support for devices, enhancing functionality and convenience within the vehicle.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents