(5)- (110 SOURCE) DRYER MOTOR KIT #279827.
INSTALLATION AND WIRING INSTRUCTIONS
for Pluggable Motor Replacement _
ThlLsIat C_nt_lnt:
I Motto A_membly
2 !/_" Ferule Tmmlnals (kwulated)
1 Sheet. to.ruction
EI,e_trlcal 8h©.:k X_,_tsrd
Dis_mtecd power INlf_
servl_g.
Failure tO do so could resuR In
s_loUa ht|ury ot death.
NOTE TO THE INS.T.A_ER: This motor kit isan authorized FSP ser_ce _e_ment
p._t.for your epphc_tlon.Themotorinthis .kitmay or maynotbe.klentl_lto your
ore.moOr, if your_re, m motor ha=the ptuggablemR _it_ (_e _ure.4B),
mpmceme eewlcemotor Inmesamemanneras you mmo_ __ motor.
If your doteOtlve motor has the switch where the wire lead from the _n harness
oonne_ rfollowInstru_ons below.
Potm_tlat Fire Hazed andlor
Nulsam_e "l'dpplng of Motor Protector
00 NOT under any c4mumstance attempt
to remove oH"replace the motor switah
from this plugglb|e _rvice motor. The
swltoh is o non-serviceable component,
Failure to do so oouid result In fire, serious
injury or death,
.
Remove Ixdley from replaaementmotor by using.two
(2) open end or adjual_de wrenches. Place one on
the motor shaft, rlghtbehb_:lglS¢ulley,_ the other
on the pulley. Holdi_the motor shelf in ple.cewith
one (1) wrench, turn puikly with o_r wrench In a
COunte_e dlmotlon to remove pulley. See
Figure E.
Remove defective motor using standarclmotor
removalprocedures.
5. Remove beltrestrainerfromreple(;eme_tmotor.,._ee
F/gum2,
2. Compare and note the difference between the
detective motor andyour new replscement motor The
first thing you will need to' compare is the motor
pulleys. The I_Uey supplied with the replaoement
motor can be used in zdl _ppgc_lons. Al_ough
g_ere m_ two (2) €_ses, you may want Io use the
pulley from the def_t_ve motor. See Rgure I forthese
_i0VE PULLEY
2.SPEED
APPUCAT_ON
FAg[IRE!
NOTE: It you choose not to reuse your pulley
from the defective mlptor as shown In Figure I,
you will loose the 2..speed or 3-speed option.
fns(rucSonSheet 279807 7194
6, From the s',_ end of b'le replacement motor, cut
the thread_l portion of the motor shMt off using a
hacksaw. See Rgure 3.
_LU_IABLE
CUI"II'IREAOED
7. _th an allenwrench, remove re pulleyt'romthe
dalec6vemotorand reinstallit on themplacemem
motor.Be _uroto pushpull_yontothemotor st,._
allthewayandtightenthe setscrewsecurelyinplace.
9. PositionmotoraSshownb_ 5.Note the locazior_
of the motor swl_. Secure zpotorto bracket with
the odglnaJmotordamps.
1
Compare and note difference between the motor
s_etah of the defe_,e motor and the switch of '_e
new mp|a_ement motor, IIthe switchesare the same,
simply inst_l] the motor in reve_ order you've
removed the defeotive motor. See F_v._e$ ,dA& 4B.
If not. proce_:l to step 9.
NOTE: Overload protector is part of the plug-
gable switch on the replacement motor and
separete on the old motog 9wit_.
OVERLOAOPROTECTOR
OLO
MOTOR
SWITCH
omen .o
RGURE'J
279807
FIGURE44
(¢ontP,_O
WIRING INSTRUCTIONS
10. Jnk.',_'A_ _r,d m..m_ the blue|uml_r witothlt runs
_rom the mot(_ sw_tohto the oved_ at_d discer¢.
SeeRgum6.
11. " s to
_'_'_------ " " _ cu
__e w_e_omlnmpto,s_eF_ra 8-
tothe V4"retrainedrrm,W,ed "l"_on the motor sw'd_.
See F_re 6.
13. Connect b'te red (:P.M),_re lead from ma]n hame,_s
_othe V,_"termlnal marked 'T on the motor swi_.
See F_ure 6.
14.'1"o oonnect b'm hie=k (61_ ,tAm le_ from n_n
h_m a_d 1he v_lte _ v_ lead from n_n
,1,-_W_ te,m_Io_a¢,_'_,__ fem_
_nin_s _ _1_ tl_e_ motor.
15. cutt_ _t4"_ _r_al _ _he _d
to I_ _mlnal _ posmo_ewTtl_wire _!_.
16. SMp wires I:_ck approndmatelyII, of _u_inch.
17. With barrel Cdml_rs, crimp V_' _ fema_
temdn_s, ln_l_l _ motto, onto_e Wireleads.
NOTE: Make sure terminels ere crimped
securely In piece.
18. C,onneol the white(SM) wire lead from milleIlarness
onto1tin_" terminalmarked "6" onthe matOrswitch.
s_ebume_
Re.E6
20. Reconnect ground_re, See Fngure_,
19. _nrzect theblack(6M) wire.leadfromm.l_nharnm_s
onlothe V_"terminalmarked"6"onthe'motorswitch. 21, All wire lead cormecllonsarecompleteat thispoint.
,SeeF/gum6. Finishreassemblingdryer.
/
