Atlas Metal Industries PHD-TA-14 1/2 Datasheet

Brand
Atlas Metal Industries
Model
PHD-TA-14 1/2
Type
Datasheet

This manual is also suitable for

a subsidiary of Mercury Aircraft
1135 NW 159 Dr., Miami, Florida 33169
Tel: (305) 625-2451 or (800) 762-7565 • Fax: (305) 623-0475
PDH-TA THERMAL AIR HEATING
PLATE DISPENSERS DROP-IN
Project Name
N
O
# Item N
O
# Quantity
CONSTRUCTION:
The basic unit shall be constructed of 300 series
stainless steel. The dispensers shall be a drop-in,
self-leveling design.
The counter top flange has three, high impact,
plastic guide posts to align plates. The unit is self
supporting, with vertical side panelsanda bottom
and top flange all welded to form the dispenser
body. The stainless steel dispenser head will be
suspended from the extension springs to support
the stack of plates to be dispensed.
PDH-TA
Basic construction with the addition of a base
mounted, THERMALLY PROTECTED FAN MOTOR
& HEATING ELEMENT, for heat circulation, side
mounted thermostat, an additional stainless steel
shield which covers the spring mechanism and
vertical channel guides, flange mounted pilot
light and on-off switch. A six foot 16-3 cordset,
NEMA5-15P, will be provided.
SELF-LEVELING:
The spring mechanism is easy to adjust. A combi-
nation of extension springs will be provided for
field adjusting to the required dispensing height.
SPECIFICATIONS
“ALL PRICES AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE”
FOR HIGH VOLUME PLATE DISPENSING
FOR CAFETERIA OR TRAY MAKE-UP AREA
OPTIONS AND ACCESORIES
CONSULT THE FACTORY FOR SPECIAL REQUIREMENTS
Special voltage
Special height
Pre-heat covers
3A
a subsidiary of Mercury Aircraft
1135 NW 159 Dr., Miami, Florida 33169
Tel: (305) 625-2451 or (800) 762-7565 • Fax: (305) 623-0475
4A
MODEL
NUMBER
WATTS AMPS
MAXIMUM
PLATE SIZE
OUTSIDE FLANGE
DIAMETER
CUT-OUT
DIAMETER
SHIPPING WT.
(lbs.)
PDH-TA-9 1/8 535 4.5 9-1/8” 12-1/2” 11-7/8” 28
PDH-TA-10 1/8 535 4.5 10-1/8” 13-1/2” 12-7/8” 33
PDH-TA-12 535 4.5 12” 15-3/8” 14-3/4” 35
PDH-TA-14 1/2 535 4.5 14-3/8” 17-7/8” 17-1/4” 38
PDH-TA THERMAL AIR HEATING
PLATE DISPENSERS DROP-IN
STANDARD FEATURES:
•
FIELD ADJUSTABLE FOR DIFFERENT WEIGHTS
•
ALL STAINLESS STEEL CONSTRUCTION
•
HIGH IMPACT PLASTIC GUIDE POSTS TO
ALIGN PLATES
•
THERMALLY PROTECTED FAN MOTOR FOR
HEAT CIRCULATION
SELF-LEVELING
PLATE DISPENSER
HEATED DROP-IN SHIELDED TUBE / THERMAL AIR
ELEC @ 120V IPH
“ALL PRICES AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE”
10/07-SC
  • Page 1 1
  • Page 2 2

Atlas Metal Industries PHD-TA-14 1/2 Datasheet

Brand
Atlas Metal Industries
Model
PHD-TA-14 1/2
Type
Datasheet
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents