Tyan S5547 User manual

http://www.tyan.com

1

S5547

Version 1.0

Copyright

this manual may be reproduced or translated without prior written consent from

MiTAC International Corporation.

Trademark

All registered and unregistered trademarks and company names contained in this

manual are property of their respective owners including, but not limited to the

following.

TYAN

®

is a trademark of MiTAC International Corporation.

Intel

®

is a trademark of Intel

®

Corporation.

AMI, AMI BIOS are trademarks of AMI Technologies.

Microsoft

®

, Windows

®

are trademarks of Microsoft Corporation.

Winbond

®

is a trademark of Winbond Electronics Corporation.

Notice

Information contained in this document is furnished by MiTAC International

Corporation and has been reviewed for accuracy and reliability prior to printing.

MiTAC assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN

®

products including liability or

warranties relating to fitness for a particular purpose or merchantability. MiTAC

retains the right to make changes to product descriptions and/or specifications at

any time, without notice. In no event will MiTAC be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this

document.

http://www.tyan.com

2

Contents

S5547 ............................................................................................................ 1

Before you begin… .................................................................................... 3

Chapter 1: Instruction ................................................................................ 4

1.1 Congratulations ................................................................................. 4

1.2 Hardware Specifications .................................................................... 4

Chapter 2: Board Installation ..................................................................... 6

2.1 Board Image ...................................................................................... 7

2.2 Block Diagram ................................................................................... 8

2.3 Motherboard Mechanical Drawing ..................................................... 9

2.4 Board Parts, Jumpers and Connectors ........................................... 10

2.5 Installing the Processor and Heatsink ............................................. 16

2.6 Tips on Installing Motherboard in Chassis ...................................... 20

2.7 Installing the Memory ...................................................................... 22

2.8 Attaching Drive Cables .................................................................... 25

2.9 Installing Add-In Cards .................................................................... 26

2.10 Connecting External Devices ........................................................ 27

2.11 Installing the Power Supply ........................................................... 28

2.12 Finishing Up ................................................................................... 28

Chapter 3: BIOS Setup ............................................................................. 29

3.1 About the BIOS ................................................................................ 29

3.2 Main Menu ....................................................................................... 31

3.3 Advanced Menu ............................................................................... 32

3.4 Chipset Menu .................................................................................. 62

3.5 Security ............................................................................................ 68

3.6 Boot ................................................................................................. 73

3.7 Save & Exit ...................................................................................... 76

Chapter 4: Diagnostics ............................................................................. 78

4.1 Flash Utility ...................................................................................... 78

4.2 AMIBIOS Post Code (Aptio) ............................................................ 79

Appendix I: Fan and Temp Sensors ....................................................... 86

Glossary ..................................................................................................... 89

Technical Support .................................................................................... 95

http://www.tyan.com

3

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1 x S5547 Motherboard

1 x Rear IO shielding

1 x S5547 Quick Installation Guide

1 x TYAN

®

Driver CD

2 x SATA Single Cable

IMPORTANT NOTE:

Sales sample may not come with the accessory listed above.

Please contact your sales representative to help order accessory for your

evaluation.

http://www.tyan.com

4

Chapter 1: Instruction

1.1 Congratulations

You have purchased the powerful TYAN

®

S5547 motherboard, based on the Intel®

Skylake PCH (H110) chipset. The S5547 is designed to support single Intel

®

Core™ i3/i5/i7 series processor, and up to 32GB of un-buffered ECC UDIMM

DDR4 2133MHz / DDR4 memory. Leveraging advanced technology from Intel

®

, the

S5547 is capable of offering scalable 32 and 64-bit computing, high-bandwidth

memory design, and lightning-fast PCI-E bus implementation.

The S5547 not only empowers you in today‟s demanding IT environment but also

offers a smooth path for future application upgradeability. All of these rich feature

sets provide the S5547 with the power and flexibility to meet demanding

requirements for today‟s IT environments.

Remember to visit the TYAN

®

website at http://www.tyan.com. There you can find

all the information on all TYAN

®

products as well as all the supporting documentation,

FAQs, Drivers and BIOS upgrades.

1.2 Hardware Specifications

TYAN S5547 (S5547G2NR)

Processor

Supported CPU

Series

Intel Core i3/ i5/ i7 series processors

Socket Type / Q'ty

LGA1151 / (1)

Thermal Design

Power (TDP)

wattage

65W

Chipset

PCH

Intel H110

Super I/O

NCT6683D-T

Memory

Supported DIMM

Qty

(2) DIMM slots

DIMM Type / Speed

Unbuffered ECC UDIMM DDR4 2133

Capacity

Up to 32GB

Memory channel

1 Channel

Memory voltage

1.2V

Expansion

Slots

PCI-E

(1) PCI-E Gen3 x16 slot / (1) PCI-E Gen3 x8 slot

LAN

Port Q'ty

(1) GbE, (1) PHY

Controller

Intel I210-AT

PHY

Intel I219-LM

http://www.tyan.com

5

Storage

SATA

Connector

(4) SATA

Controller

Intel H110

Speed

6.0 Gb/s

RAID

Non-support

Graphic

Connector type

(1) Display port

Chipset

Intel H110

Input /Output

USB

(5) USB2.0 ports (4 at rear, 1 Type-A)/ (4) USB3.0

ports (2 at rear, 2 via cable)

COM

(1) header

Display port

(1) Display Port

RJ-45

(2) GbE ports

Power

ATX 24-pin + 4-pin power connectors

Front Panel

(1) 2 x 5 header

SATA

(4) SATA-III connectors

System

Monitoring

Chipset

NCT6683D-T

Voltage

Monitors voltage for CPU, memory, chipset & power

supply

Fan

Total (4) 4-pin headers

Temperature

Monitors temperature for CPU & system environment

Others

Watchdog timer support

BIOS

Brand / ROM size

AMI / 16MB

Feature

Hardware Monitor / ACPI 5.0 / SMBIOS 3.0/PnP/Wake

on LAN / ACPI sleeping states S3,S4,S5 / Boot from

USB device ,PXE via LAN ,Storage / User

Configurable FAN PWM Duty Cycle / Console

Redirection

Physical

Dimension

Form Factor

Flex ATX

Board Dimension

9"x7.5" (228.6x190.5mm)

Operating

System

OS supported list

Please refer to our Intel OS supported list.

Regulation

FCC (DoC)

Class B

CE (DoC)

Yes

Operating

Environment

Operating Temp.

10° C ~ 35° C (50° F~ 95° F)

Non-operating

Temp.

- 40° C ~ 70° C (-40° F ~ 158° F)

In/Non-operating

Humidity

90%, non-condensing at 35° C

RoHS

RoHS 6/6 Compliant

Yes

Package

Contains

Motherboard

(1) S5547 Motherboard

Manual

(1) Web User's manual / (1) Quick Installation Guide

Installation CD

(1) TYAN installation CD

http://www.tyan.com

6

Chapter 2: Board Installation

You are now ready to install your motherboard.

How to install our products right… the first time

The first thing you should do is read this user‟s manual. It contains important

information that will make configuration and setup much easier. Here are some

precautions you should take when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the

antistatic bag. Unplug the power from your computer power supply and

then touch a safely grounded object to release static charge (i.e. power

supply case). For the safest conditions, MiTAC recommends wearing a

static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the

board, or flex the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors,

memory modules, and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic

bag that the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your

chassis, as well as installing the processor, memory, disk drives and cables.

Caution!

1. To avoid damaging the motherboard and associated

components, do not use torque force greater than

7kgf/cm (6.09 lb/in) on each mounting screw for

motherboard installation.

2. Do not apply power to the board if it has been

damaged.

http://www.tyan.com

7

2.1 Board Image

S5547G2NR

This picture is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the above picture.

http://www.tyan.com

8

2.2 Block Diagram

S5547 Block Diagram

http://www.tyan.com

9

2.3 Motherboard Mechanical Drawing

http://www.tyan.com

10

2.4 Board Parts, Jumpers and Connectors

This diagram is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the above diagram. The

DIMM slot numbers shown above can be used as a reference when reviewing the

DIMM population guidelines shown later in the manual. For the latest board revision,

please visit our web site at http://www.tyan.com.

http://www.tyan.com

11

Motherboard Components

Connectors

1. RJ45 LAN Port #1 (LAN1) + Dual USB2.0

ports (J6)

14. USB 3.0 HDR (J14)

2. Display Port (J7)

15. INTRUDER HDR (INTRD1)

3. LPC Header (J8)

16. 7pin SATA 3.0 Connector (SATA 3) (J25)

4. Port 80 Header for CPLD (J4) for EFI

17. 7pin SATA 3.0 Connector (SATA 2) (J26)

5. JTAG Header for CPLD (J3) for EFI

18. 7pin SATA 3.0 Connector (SATA 1) (J27)

6 Dual USB 2.0 Ports (USB1)

19. 7pin SATA 3.0 Connector (SATA 0) (J28)

7. RJ45 LAN Port #2 (LAN2) + Dual USB3.0

ports (J5)

20. SYS FAN (J29)

8. LAN2 LED HDR (J1)

21. 24 pin power connector (J24)

9. Port80 Debug Header and TPM HDR

(DBG_HD1)

22. Front FAN (J30)

10. Rear FAN (J2)

23. CPU FAN (J16)

11. COM port HDR (J10)

24. 4-Pin ATX Power Connector (PWRCONN1)

12. Front Panel HDR (J11)

25. LAN1 LED HDR (J12)

13. USB2.0 TYPE A Connector (J13)

Sockets/Chipset/Buttons

CPU Socket (U7E1)

iii Intel H110 (SKL PCH) (U3F1)

BIOS Socket (E1)

ii Nuvoton NCT6683D-T SIO (U3)

SIO F/W Socket (E2)

i SMB Bus Socket for CPLD (J23) for EFI

Jumpers

a ME DISABLE Jumper (J15)

c Recovery Jumper (J19)

b Clear CMOS Jumper (J17)

d Buzzer Jumper (J20)

Slots

A PCIE X16 slot (PCIE_X16_SLOT1)

B PCIE X8 slot (PCIE_X8_SLOT1, signal up to X4)

C DIMM_A0 (J8C1)

D DIMM_B0 (J8C2)

http://www.tyan.com

12

J3: JTAG Header for CPLD (for EFI)

Signal

CPLD_JTAG_TCK

1

2

GND

CPLD_JTAG_TDO

3

4

+3.3V

CPLD_JTAG_TMS

5

6

NC

7

8

GND

CPLD_JTAG_TDI

9

10

KEY

J4: Port 80 Header for CPLD (for EFI)

Signal

CPLD_SMBCLK

1

2

+3.3V

CPLD_SMBDATA

3

4

CPLD_7SEG_LEDA

CPLD_7SEG_DGH_LR

5

6

+3.3V

GND

7

8

CPLD_7SEG_LEDB

CPLD_7SEG_DGL_LR

9

10

CPLD_7SEG_LEDC

SIOGP75

11

12

CPLD_7SEG_LEDD

SIOGP76

13

14

CPLD_7SEG_LEDE

CPLD_7SEG_LEDG

15

16

CPLD_7SEG_LEDF

J16 (CPU FAN) / J30 (Front FAN) / J2 (Rear FAN): 4-pin FAN Connector

1

2

3

4

Signal

GND

VCC12

TACHOMETER

PWM

Use this header to connect the cooling fan to your motherboard to

keep the system stable and reliable.

Note: A 4-pin fan is required for fan support 4pin Control

http://www.tyan.com

13

J29 (SYS FAN): 4-pin FAN Connector

1

2

3

4

Signal

GND

VCC12

TACHOMETER

VCC5

Use this header to connect the cooling fan to your motherboard to

keep the system stable and reliable.

Note: A 4-pin fan without FAN speed Control

J11: Front Panel Header

Signal

VCC5

1

2

GRN BLNK HRD

SATA LED

3

4

YLW BLNK HRD

GND

5

6

PWRBTN

FP RST

7

8

GND

VCC

9

10

KEY

J14: Front USB3.0 Header

Signal

5V_AUX

1

2

USB3_RX_N

USB3_RX_P

3

4

GND

USB3_TX_N

5

6

USB3_TX_P

GND

7

8

USB_DN

USB_DP

9

10

USB_OC#

USB_DP

11

12

USB_DN

GND

13

14

USB3_TX_P

USB3_TX_N

15

16

GND

USB3_RX_P

17

18

USB3_RX_N

5V_AUX

19

20

Key

SATA0(J28)/SATA1(J27)/SATA2(J26)/SATA3(J25) : 7-pin vertical SATA3.0

Connector(Blue)

7

1

Name

TYPE

S1

GND

S2

SATA TX DP

S3

SATA TX DN

S4

GND

S5

SATA RX DN

S6

SATA RX DP

S7

GND

Connects to the Serial ATA ready drives via the Serial ATA cable.

http://www.tyan.com

14

DBG_HD1: TYAN Module Header (Port80 Debug Header)

Signal

P3V3

1

2

FRAME_N

LAD0

3

4

KEY

LAD1

5

6

PLT_RST_N

LAD2

7

8

GND

LAD3

9

10

CLK_24M

DBG_SERIRQ

11

12

GND

DBG_PRES_N

13

14

VCC3_AUX

TPM_ADDR_MB

15

16

PCH_TPM_PP_EN

J10: COM Header

Signal

DCD

1

2

DSR

SIN

3

4

RTS

SOUT

5

6

CTS

DTR

7

8

RI

GND

9

10

KEY

J13: Vertical (Type A) USB2.0 Connectors

1

2

3

4

Signal

5V_AUX

USB_DN

USB_DP

GND

J8: LPC Header

Signal

+3.3V

1

2

LPC_LFRAME_N_ESPI_CS0

LPC_LAD0_ESPI_IO0

3

4

KEY-Pin

LPC_LAD0_ESPI_IO1

5

6

NIC_RESET#

LPC_LAD0_ESPI_IO2

7

8

GND

LPC_LAD0_ESPI_IO3

9

10

CLK_24M

J1: LAN2 LED Header

1

2

Signal

LAN1_LED1_FP+

LAN1_LINK_ACT#

J12: LAN1 LED Header

1

2

Signal

LAN2_LED1_FP+

LAN2_LINK_ACT#

http://www.tyan.com

15

INTRD1: Intruder Header

1

2

Signal

GND

INTRUDER

J15: ME DISABLE Jumper

Pin 1-2 Closed: Normal Mode (Default)

Pin 2-3 Closed: ME Disable Mode

J17: Clear CMOS Jumper

Normal (Default)

You can reset the CMOS settings by using this jumper. This can be

useful if you have forgotten your system/setup password, or need to

clear the system BIOS setting.

1. Power off system and disconnect power connectors from the

motherboard.

2. Remove the jumper from Pin_2 and Pin_3 (Default setting).

3. Move the jumper cap to close Pin_1 and Pin_2 for several seconds

to Clear CMOS.

4. Put jumper cap back to Pin_2 and Pin_3 (Default setting).

5. Reconnect power connectors to the motherboard and power on

system.

Clear CMOS

J19: Recovery Jumper

Pin 1-2 Closed: Normal Mode (Default)

Pin 2-3 Closed: Configure

Remove Cap: Recovery

J20: BUZZER Jumper

Pin 3-4 Closed: Disable

Pin 2-3 Closed: Disable

Pin 3-4 Closed: Enable (Default)

http://www.tyan.com

16

2.5 Installing the Processor and Heatsink

The types of processors supported by the S5547 are listed in the 1.2 Hardware

Specifications section on page 4. Check our website at http://www.tyan.com for

the latest list of validated Intel

®

processors for this specific motherboard.

NOTE: MiTAC is not liable for damage as a result of operating an

unsupported configuration.

Processor Installation (SNB_H4 (LGA1151) for Intel Skylake CPU)

Follow the steps below to install the processors and heat sinks.

Please note that the illustrations are based on a SNB_H4 (LGA1151) which may not

look exactly like the motherboard you purchased. Therefore, the illustrations should

be held for your reference only.

NOTE: Please save and replace the CPU protection cap when returning for service.

1. Locate the CPU socket.

2. Pull the CPU lever slightly away from the socket and then push it to a fully

open position.

3. Open the CPU socket cover.

http://www.tyan.com

17

4. Remove the CPU protection cap.

5. Install the processor and make sure the gold arrow is located in the right

direction with two notches properly aligned.

6. Close the CPU socket cover.

7. Press the socket lever down to lock the CPU in place.

http://www.tyan.com

18

Heat sink Installation

After installing the processor, you should proceed to install the heat sink. The CPU

heat sink will ensure that the processor do not overheat and continue to operate at

maximum performance for as long as you own them. The overheated processor is

dangerous to the motherboard.

For the safest method of installation and information on choosing the appropriate

heat sink, using heat sinks validated by Intel

®

. Please refer to the Intel

®

website:

http://www.intel.com

The following diagram illustrates how to install the heat sink for the SNB_H4

(LGA1151) socket.

1. Apply the thermal grease.

2. Place the heat sink on top of the CPU and push the 4 latches in a diagonal

pattern to lock it in place.

http://www.tyan.com

19

3. Secure the heat sink screws.

4. Connect the fan cable to complete the installation.

http://www.tyan.com

20

2.6 Tips on Installing Motherboard in Chassis

Before installing your motherboard, make sure your chassis has the necessary

motherboard support studs installed. These studs are usually metal and are gold in

color. Usually, the chassis manufacturer will pre-install the support studs. If you are

unsure of stud placement, simply lay the motherboard inside the chassis and align

the screw holes of the motherboard to the studs inside the case. If there are any

studs missing, you will know right away since the motherboard will not be able to be

securely installed.

Note: Be especially careful to look for extra stand-offs. If there are any stand-offs

present that are not aligned with a mounting hole on the motherboard, it will likely

short components on the back of the motherboard when installed. This will cause

malfunction and/or damage to your motherboard.

Page is loading ...

Tyan S5547 User manual

Tyan S5547 User manual

Related papers

Other documents